So, you decided to equip the wooden shower in the country with your own hands - where do you need to start? Of course, with choosing a place for shower and design. The next step will be.
After that, go to the construction of walls. When this stage is behind, you can enjoy the floor, roofs and door mounting. Well, now about each of these stages in more detail.
Before making a wooden shower with your own hands, you need to carefully approach the choice of space for it. If the heating of water in the shower tank will occur only from the sun, the place for the summer soul should be only on the sunny side.
The water tank should be located under the influence of sunlight as long as possible during the day, especially in the morning clock. In this case, the water will warm up to a comfortable temperature. It is desirable that the sun illuminates the shower cabin. In addition, it should be placed in such a way as not to blurred by the winds.
Also, before making a shower of a tree, a place where it will be erected, it is necessary to equip the flow and drain system.
For normal operation of the summer shower, high-quality removal and fast recycling Sew water. When the garden soul is located on an exalted place, a good water outflow is naturally provided. In the heat, the load on the summer souls increases significantly.
It is necessary to take into account the possibility of not only the supply of clean water, but also the devices of a concreted receiving well for wastewater. To do this, equip a drain pit with a volume of about 2 m. If a small water consumption is required for the summer shower, then you can not do the drainage system. Water after bathing will be absorbed by itself, even if there is a waterproof clay on the plot under the soil layer.
If the family consists of 2-3 people, then for the reception of the soul is enough for several tens of liters of warm water. For 4 people and more water needed to receive a soul, increases to several hundred liters.
If you make your own hands wooden shower with extra heated, you need to arrange it away from the residential building.
When the device should be remembered about the nature and properties groundwater. If in the garden sand soilIn depths, it usually be littered with a clay rock. Then the water used from the shower can easily be leaked inside the soil to the clay layer, and on it it will fall into the aquifer or local reservoir. At the same time, there is a danger of getting shifting in well water.
Before making a wooden shower, you need to make it a project. To do this, you need to decide on the size of the future design. For a good jet pressure, it is necessary to arrange a water container with water at an altitude of 2.5 m. Of great importance is the convenience of the cabin, so that you can comfortably wash under the shower anytime. If the sizes of the cabin are at least 2 x 1.5 m, then inside it you can arrange a hanger for clothes, a shelf for soap, etc.
Having equipping the summer souls from the tree with their own hands, remember that the size of the internal space in the cabin should be at least 100 x 100 cm so that it is possible to freely raise the hand or burn, not bumping onto the walls.
The cabin should have a shower room and a dress-protected dressing room, the width of which is usually at least 60 cm, so inner space Summer shower booths cannot be less than 160 x 100 cm. It is advisable to design a 190 x 140-cm design. To these parameters, the wall thickness should be added, resulting in 200 x 150 cm.
For the construction of a wooden summer soul, do not require a special foundation. Installation technology implies strict adherence to the strict verticality of frame racks and durable connections with strapping. At the same time, supports must be tightly rely on lining. Compliance with these rules is necessary, since a heavy water tank will be installed at the top. After determining the dimensions, it is necessary to make markup, designating a rectangle with dimensions 170 x 110 cm or 190 x 140 cm on Earth or 190 x 140 cm. The height of the summer country soul can be 2.5-3 m. With a small area of \u200b\u200bsupport, it will not be sufficiently stable. To avoid overturning the design, it is recommended to equip the pile or. It is easy to raise, but it will safely be able to keep the shower in the wind and other loads, since the water tank with a volume of 200 liters has a significant weight. As a material for foundation, you can use metal poles, metal or asbestos-cement pipes with a diameter of 90-100 mm and a length of 1.5-2 m. After that, in the ground in the corners of the shower, four wells should be drilled in a depth of 1-1.5 m. They should insert pipes or pillars so that each Of these, they rummaged above the ground level of at least 30-50 cm. Then, at the corners of the foundation from the poles, you need to lay a trimmed with a sequence of 100 x 100 mm.
Living a pillars when erecting a wooden summer shower for giving with their own hands, you can produce in the form of a closed strapping, starting from the top.
This design of the foundation is a rigid frame. It is more convenient to collect it on Earth, and then fasten with long bolts.
The structure strength is ensured by the coincidence of all axes. In addition, the bond must be performed using long bolts. In this case, on the roof of the soul it will be possible to install a volume barrel of about 200 liters. The most stable is the shower cabin, if there are six foundation pillars under it. Under a columno foundation, six holes with dimensions of 20 x 20 or 30 x 30 cm and a depth of 40-50 cm. Sizes and depth depends on the structure of the soil. Pans need to fill in cement-sandy solution mixed with pebbles or gravel.
Places for scene scene are ready. The base of the soul frame of the tree from the tree to the country should be made waterproof, with a slope of the drain, which is connected to the water removal system. Between the pit, it is necessary to remove the top of the soil to the depth of 20 cm, and at the edges of the pit formed, it is necessary to strengthen the formwork from the boards or plywood.
The deepening under the shower can be displayed by rubberoid or PVC film, but it is better to concrete it, forming a kind of water belonging pan, so that the land does not hire under the country's shower. After that, the bottom of the pit need to fall asleep sand, shed water, tamper, and then pour the solution in such a way that the site towers over the ground is 10 cm and captured the place under the foundation.
From a pallet, which has a small bias, water will go to the wastewall, so the slope must have a drainage gutter. Drain of water from the summer shower must be organized in a special septic ditch (septic) located on the site or beyond. Water should be discharged through a pipe laid in a trench with a certain bias towards the waste hole.
Under the shower of wood, you can arrange ribbon foundation A depth of 30 cm without a monolithic concrete site. In order to give a future design, the correct geometric shape must necessarily check the equality of the diagonals of the foundation using the rope or thick life. After that, you can proceed to digging the trenches of 30 cm x 30 cm. The foundation should be poured with a concrete solution prepared from 1 part of cement, 3 parts of pure sand and 5 parts of a crushed stone fraction (5-20 mm).
Before preparing the solution, sand needs to be carefully sifted. The solution must be pouring into the dug trench. When it completely freezes, using a level to check the horizontal foundation.
If there are any irregularities, they need to be aligned using cement-sandy solution. If constant use of the shower is assumed, then under the foundation it is necessary to pour a concrete site or lay it out of a brick in the form of a rectangle. Concreting the foundation site should be made with a bias sewer pipeAnd on top to put a wooden grid.
When erecting the walls of a wooden shower cabin with their own hands, it should be borne in mind that high humidity Wood can start rotting, so it should be processed special means against rot. She has a number of advantages: it is environmentally friendly, externally attractive and rather durable material.
If there is no possibility from wood all the booth, you can use a tree for the construction of carrier pillars. The remaining details will easier to attach to the wooden columns than to metal pipes. The construction of the shower walls should be started from the hard frame device.
For a skeleton frame, you will need four cast iron pipesBut you can apply any other material available. For pipes in concrete or brick foundation Holes should be prepared, insert pipes there and concrete them for strength. When the cement solution is completely dry, you need to move to the setting of slate sheets. For such a booth, three slate sheet will be required. They should be attached from three sides directly to the prepared frame.
The fourth side will be located the door. The frame for the booth can be made of metal corners. The two elements are the lower and top "circles" made of metal corners. For them, you can use angle 30 x 30 mm.
The third element of the frame is binding "circles": pieces of metal reinforcement with a diameter of 12 mm and the required length. For greater strength of the structure, the lower "circle" of the frame should be concreted in the base. Vertical fittings are recommended to complement several wooden bars to make it easier to mount the material used to cover the cabin.
Pillars for shower of wood do it yourself best to sew from two sides wooden clapboard. Such walls will reliably protect the structure not only from the cold, but also from the heat. Since the frame poles are usually located at a distance of approximately 1 m, then the intermediate frame is not necessarily.
Horizontal planks can be fixed directly to the angular columns. For these purposes, you should use slate, sheet asbement or other materials. Plastic and metal used is allowed, but not recommended.
For the device of the simplest version of the shower, the summer soul will need boards and bars for facing the room, as well as brick and cement for base styling.
After marking and preparing the base of the bars with the help of brackets and anchors, it should be attached to the foundation, then shelter them with boards or clapboard. On the perimeter, the bars must be associated in three places.
When erecting a shower cabin made of wood with your own hands for the framework of the framework, it is recommended to choose a bar of 100 x 100 mm.
After working on the foundation and external strapping, it is necessary to dress inside the framework, which will serve as lags for the floor shower. Between the adjacent pillars should be made of rigid elements (hips), which must be installed in the thickness of the wall itself. Most often, the walls of the summer soul are arranged in the form of shields from planed in a quarter of boards.
To the construction of summer wooden soul It is necessary to fit thoroughly. To give the entire design, the necessary stability is required to determine the base of bars or insert them into the ground. Before that, they should be sketched or linked with machine oil. In addition, they can be wrapped in rubberoid. This is done in order to prevent the decoration of the tree in the ground. The support pillars from above must be interconnected with a dressing of the same timber. This will give the strength of the whole structure that can withstand weight up to 200 kg. After that, you can proceed to the bottom dressing, which will become the base for the floor of the soul.
Walls should be treated wooden boardshaving previously treated with oliff, which will prevent wood rotting. The walls are recommended to be insulated using a foam or one of the modern insulation from foamed PVC.
One of the most pleasant and useful inventions of humanity is shower. For accustomed to civilized adoption of water procedures of urban residents, there has been no discomfort during their stay in the country area or country households with the possibility of only summer accommodation. Shower on panstone Or in the courtyard of a private house, used in the warm season - it is not easy to obtain pleasant and so necessary in the heat of water procedures, but also an important element landscape design. The appearance of the shower, panel or just racks plays a role in the formation of the image of the entire site, outdoor territory. Those times were passed when the summer souls was a non-frosted structure, designed from materials that remain from the main construction or a shed or attic found on the bumps. Modern building materials, original plumbing solutions and many creative designer ideas Capable to make a common place to take the soul of the highlight of the landscape design, a key element of the arrangement of the local area.
If we talk about the qualitative division of the summer soul designs, then all models can be classified into open and closed. Such a separation is very conditional, because there are many examples of the structure of the summer soul in semi-closed fencing of spaces. For example, the summer shower can be equipped in the zone fenced with only two partitions, placing on one plumbing accessories, and on a different hooks for placing clothes, towels, and so on.
In addition to the design of the soul itself, summer designs can be divided according to the method of supplying water to capacitive and water supply. In the first case, the reservoir is located above the top of the top of the soul, in which the water is heated from the sun's rays. In the second case, water obtained from the overall water supply system is used.
The choice of water supply system in the watering can directly affects the arrangement of the design in relation to the house. If the summer shower is located near the building of the private house, then it is logical to use not only watering system, but also the drainage of sewage. If the capacitive summer souls is located in the country area or in the courtyard of private home ownership, there is a building, it will be necessary to take care of the drainage system. It is important to understand that it is impossible to simply send the stock used water in bed cottage plot Or under the trees, because the adoption of water procedures may be accompanied by the use of funds whose impact on plants can have a detrimental effect.
One of the traditional velocities of the summer soul is considered to install the shower. Such a structure can be made of wood (in natural color or painted), polystyrene panels (most often using a metal frame) or other technicians. Moreover, you can purchase a ready-made cabin, order an individual manufacturer or to build a fence for the summer soul yourself (in the presence of elementary skills).
Wooden shower cabin in its natural manifestation is not only a practical structure, but also a beautiful element of landscape design. The natural drawing of wood is perfectly combined with almost any facade finishing material. Not to mention the fact that natural color fits perfectly into the surrounding landscape, relying with perennial plants and other buildings on the plot and in the courtyard of a private house. But the wood of the shower cabin will need to be protected from the constant impact of moisture. A wide selection of antiseptics and special varnishes are available, capable of protecting natural material from rotting and not affect wood color.
For anyone who does not want to break their heads over the coatings for the wooden cabin, there is a universal option - painting. Depending on the color solutionsAdopted for the design of the facade of the building, fashionably pick up a harmonious option for a closed facility for water procedures in the fresh air. First option - matching color palette architectural ensemble, combinatorics, both with the main building and with additional buildings on the site (terrace, gazebo or garage). The second option is the performance of the shower cabin as a color accent. This method of creating a color stain is used infrequently, because the summer shower is a seasonal building, operated in our country only in the summer.
The location of the summer soul near the wall of the house has its advantages and disadvantages. On the one hand it is convenient that you can use the overall water supply system and sewage system located in household. On the other hand, the wall of the building will constantly experience the impact of moisture. It is desirable to protect the surface with a ceramic tile or any other material that effectively opposes high humidity. It is also necessary to trace the organization of good drainage system. Otherwise, constant cluster of water in the foundation of the building can gradually destroy it.
Another advantage of using the house wall for organizing water treatment places is the ability to use the lighting of the facade of the main building. If you need to take a shower in the dark, it will not be necessary to worry about the availability of artificial lighting - the facade of the building in any case is subjected to illumination for safety and as an element of landscape design.
An excellent way to protect the wall of the house from the constant impact of moisture is a cladding with a ceramic or stone tile. In this case, there is no limit to implement your fantasies and the manifestation of stylistic preferences. Ceramic tile "under marble", monotonous or ornament, large or small - it all depends on your personal preferences. If there is a swimming pool on the site, then it will be logical to agree on the wall decoration to place the soul with the design of the space in the street tank and around it.
Stone tile (or its spectacular imitation) will look luxuriously as a wall decoration to which sanitary accessories are attached - a shower and a mixer. In combination with greens, the stone surface gives the creation of an image approximate to the natural nature.
One of the options for the decoration of space in which accessories are located for the adoption of the soul - the use of metal sheets. Stainless steel or aluminum look great in the composition made in the style of high-tech or any direction of modern stylistics. In order to strengthen the effect of originality finishing material You can use original accessories - large wandels of square or rectangular shape, imitation of tropical rain or waterfall.
With the help of a metal sheet, you can build something like a small cabin for taking a shower in the summer at the country area or in the courtyard of private home ownership. Nekazy appearance It is estimated at the cheap structure and temporary accommodation at the local area.
Summer shower can be equipped with devices that give additional features For the adoption of water procedures. For example, the construction of an additional crane at the lower level of the rack or panel will give you the opportunity to wash only your feet after working in the garden or the ablution of pets directly on the plot.
Any partition can be played as a panel to accommodate the soul - from stone, wood or other materials. The advantage of such structures is that it requires a smaller amount of materials and efforts. At the same time, you get a zone for the adoption of water procedures that abundance of moisture does not harm the main structure. But such a summer soul has disadvantages. The soul's adoption not protected from the wind may cause for colds from households who do not know anything about hardening the body.
Using a beach style for decoring a shower panel can be a highlight of your landscape design. It is not necessary to live on the ocean to be able to apply the panel in the form of a surfboard when arranged a zone for the adoption of water procedures.
To finish the panel to which the plumbing accessories will be attached perfectly fit the ceramic tile or mosaic, reliably protecting the surface from moisture. But also more democratic accounted options can be an effective solution - plastic and polyurethane panels will serve as reliable finish.
The use of non-standard, original plumbing accessories can enhance the degree of uniqueness not only the shower sector, but also the entire landscape design of the country or household site. Large watering cans for imitation of tropical rain, a small waterfall or vice versa miniature mixers, original forms and unusual covers - your fantasy stops only the budget for the construction of the summer soul.
The panel for placing the shower sector can be the sector of the fence. It all depends on the location of buildings on your site, passing systems of communications and the type of fence design. For example, stone concrete, wooden structures (with impregnation and protective coating) can be an excellent base for placing sanitary accessories.
A shower rack for water procedures in the warm season can be located on an outdoor terrace, for example, by the pool and serve as a means of ablution before visiting water. Also, the summer shower can be equipped on the covered terrace, which serves as a place of relaxation in the fresh air.
On the one hand, the placement of the soul on the terrace complicate the process of design and training itself - after all, it is necessary to bring the water supply and ensure reliable drain used water. But on the other hand, a sector remote from the main structure provides a minimal impact of moisture (and in the summer season, the owners often use showers) on the building of a private or country house.
One of the easiest, but with the effective ways to facilitate the soul on the country or the preservation section - the use of a rack with a watering can or any other water supply device. In essence, you only need to provide water supply (as a rule, with these there are no problems, because in any case pass water pipes) And the drain into the sewer. With this approach, it is possible to ensure the conditions for the adoption of water procedures, as close as possible to natural and even wild. Stormy vegetation, shower, imitating tropical shower, smells and sounds of nature - what else is needed for relaxing ablution?
Some types of racks, which are a ready-made solution for the arrangement of the summer soul in the country or in a private yard, can be equipped with a tank for heating water from sunlight. The rack itself can perform the reservoir functions. This is a wonderful alternative for regions with water supply interruptions in the summer - you will always have a small supply of water, which is enough for fast shower taking even during the water disconnection in the water supply system.
Summer shower - Choose a practical and original design
Shower cabins for cottages - one of those "facilities", which are easy to do on their own, and it is very difficult to do without them. There is a huge number different options Shower Cabin, each master contributes their improved its design. We will not dwell on complex and expensive versions, consider the most "budget", but very functional solutions.
Before starting construction, decide what you want to have in the end, what capabilities and characteristics should have a shower. Specific features of the shower cub depend on:
Street showers from Gabion 
Street souls 
Street shower of bricks (stone) 
Big Wood Street Shower
On the size of the cabin it is not worth "save", make it in a height of at least 2.2 meters, the size of the base is at least 1 × 1 m. The fact is that the cabin should have a place for bath accessories and clothes. Consider step by step two options for cabins - with a metal and wooden frame.
summer Shower Shower Cab
Metal shower 
Shower cabin S. metal carcasy
Shower cabin do it yourself at the cottage photo
For the production of work, you will need square pipes with a cross section of at least 20 × 30 mm, sheet iron with a thickness of 1 mm and a 45 × 45 mm corner. Tools - angular grinding machine (Bulgarian) and welding machine.
GOST 8639 82 Steel Square Pipes 
Iron leaf galvanized 
Corner 45 x 45
Step 1. Draw a sketch of the booth.
The height of the cabin is about 2.2 meters, the size of the perimeter is 1 × 1 m.
For rigidity, refer to three rows of jumpers: at the top, in the middle and below. For the lower jumpers, it is better to use the corner, a wooden grille will be installed on its shelves. At the top, it is necessary to make stops for placing the water capacity, the specific dimensions of the stops depend on the size of the container.
Side surface can be sewed with a metal profile, a cellular polycarbonate, plastic or wooden clapboard or trimmed with various flexible materials. Under each material you need to think over the place for fastening. Drill mounting holes in square trumpet. It is impossible to make metal plates for these purposes.
Do not be too fascinated by cellular polycarbonate for the trim. It is good for many indicators, but only a limited time. One of the disadvantages that manufacturers never mention have never mentioned - moss will begin to grow in cells. And no compactors will help, the power of nature will overcome any protective measures. The type of leaf polycarbonate with moss inside you will not please and this is mildly. We generally advise showers cover light and cheap soft materials. You can change them every season to new, the cabin will always have an attractive view without a lot of time and finance loss.
a metal sheet
Step 2.
If you already have an idea of \u200b\u200bthe frame of the frame, you can start it.
Start working from cutting metal elements. Cut 4 2.2 meters long tubes (vertical supports). If you wish to do open doors in the booth, you will need to cut off two more pieces of pipes, the length can already be smaller, the size of the door height is enough to withstand within 1.5 m.
Under the focus of the grille, you will need four corners one meter. The same length you need to prepare pipes for jumpers of side surfaces and doors. They will be required by two for each element of the cabin. You need to cut the details only by the template, all the angles are strictly 90 °.
It is very important: observe the safety regulations while working with a grinding machine, injuries can be very heavy. Some "craftsmen" set cutting discs in such a way that the sparks during work flew in the opposite direction from them. This is a gross mistake! In this position, the Bulgarian undermines with a huge effort, to keep the tool in his hands is impossible.
Step 3..
Check the sections of the sections and read them for welding. The champecker can not do, the strength of the welding seam and so it will endure the load.
Step 4..
To increase the strength of the structure, harvest metallic equilateral corners, the length of cathets is 5 ÷ 10 centimeters. Set them preferably at all corners of the frame and doors. Under the feet you need to weld the square stops ≈20 × 20 cm.
Triangles to enhance the design
Step 5.
Welding frame. Works are very careful, never immediately lift the full seam on one side. During the cooling, it will pull the metal, return its original position will be very difficult. Initially, the contiguous pipes on the one hand, fir the design and only after that you can put a complete seam with the opposite. Sow cooled - brew the place where you have naked.
For welding, you can use Ø4 mm alternating voltage electrodes.
This is the most universal diameter of the electrodes, you can cook metal with a thickness of 1 ÷ 4 mm. Correct current strength, the metal should melt under the electrode on the desired depthBut do not cut through the wall of the pipe completely. If you do not have experience welding work - Better contact for help to a professional. This eventually costs cheaper than to translate expensive material in marriage itself.
Works need to be performed on a flat platform, constantly monitor the corners of the structure. The frame will stand on metal plates-legs of approximately 20 × 20 centimeter in. Prepare them and breed.
alternating voltage electrodes
Step 6.
Build frame. Alone, these works do not do, you need to call an assistant. Welcome separate framework elements in the specified way, constantly check its spatial position. In the lower part, the corners are welded on which a wooden grille will lie, make a design for water tank top.
Summer shower at the cottage - frame 
Step 7.
Finish finish. Carefully remove the grinding machine all sowers and sharp corners, clean the metal structures from rust, oil and dirt.
We remove the weld at this stage you can stop or continue processing for better results. 
For staining, use special paints for metal. It is necessary to dye at least twice, the metal will be viewed after the first time. Do not use pneumatic spray gun, it is suitable only for painting large surfaces. In your case, most paints "leave" in the air. Krable only with a tassel, you will not need more than one to two hours.
In the photo - Anticorrosive Metal Forms
Next, you can make wooden grids under the feet and start using water tank. How to install a container and connect the shower we will tell at the end of the article after the description of the manufacture wooden carcass Shower cabin.
Linear dimensions may be the same as in the variant with a metal frame. Production Material - Wooden Bars 50 × 50 mm, 50 × 100 mm Boards, Pick Specific Sizes Taking into account the total weight of the water capacity. Boards and bars need to be skipped through a flight - levels size and grinding roughness.
Step 1. Draw a sketch. It will come in handy not only during work, it is much easier to choose optimal option Designs. It is better to correct your mistakes on paper than on the finished product. Draw on paper a few options, think over the location of the stops, shelves and tanks for the container. Compare several sketches of shower cabins and select the most suitable for yourself.
Step 2. In size, cut all blanks for the frame, according to the scheme it is not different from the metal. Once again, pay attention - follow the dimensions, make the workpiece only in templates.
Step 3. On the flat site, start collecting individual structural elements. The connection is better to do in Polterev. If it is difficult for you - use metal plates and corners on self-drawing.
Step 4. Collect individual framework elements into a single design. If there are doors - strengthen them on the loop.
Instead of doors, you can make an ordinary curtain. Provide a water tank installation location.
Attach the shelf for bath accessories and hooks for towels and clothing from the inside. Prepare a wooden lattice for the legs.
Wooden grille - example 
Step 5. The ends of the vertical racks need to be protected from rotting. You can process them with special antiseptics, and can be soaked with olifa or sunflower oil several times. By the way, the olifa is a crude oilseed oil, including sunflower.
Let's give a few practical Soviets on the device of the shower.
You can find tips to put shower cabins on screw foundation, Pour a concrete site for them, etc. Do not advise you to engage in such works for several reasons.
Under the foundation we advise you to use paving slabs or a wide blocking. Remove with a small layer of the Earth under them, align the tile on the prepared places along the horizon. Match it a little - it will eliminate the appearance of the distillation during the use of the Cabin.
And here you can find tips on the device of the whole engineering system. What does practice show? The volume of water tank rarely allows you to simultaneously take shower more than two people, the flow rate for each approximately 20 ÷ 30 liters. Water heating time depending on the weather ranges from five hours. We assure you that during this time the water used will calmly go to the ground. And yet - you should not fear that without a sump "There will be unpleasant smells", it is not sewage.
You can build the most beautiful and most reliable shower room, but it will be very uncomfortable in it. Cause - Incorrect installation of water and shower tank. How to avoid such trouble? Let's give several practical recommendations.
Water tank. You can use two options: plastic and metal.
Advantages: relatively low price, a wide selection of capacity, ease of installation.
But there are significant disadvantages.
Advantages - High Metal Strength Guarantees the tightness and reliability of the shower attachment. Metal is easy to paint black, and such a color significantly increases the efficiency of water heating by sunlight.
Disadvantages - increase weight. You can not pay attention to corrosion processes, a thick-walled barrel will stand decades. Especially since the water barrel is corrosive much slower than empty. We advise you to use metal barrels: cheap and securely.
Another important question is how to fill with water tanks. Pump buckets - not the most the best way. We strongly advise you to take all measures to fill the water with a hose. If you have a well or well located at a great distance from the booth, you can make a temporary line of a flexible gender from the cottage. We will also tell you how to make water in automatic. To do this, you can use an ordinary float from the drain tank toilet bowl. Adjust it to the difference of triggering about twenty liters of water, taking into account the size of the container. It will make it possible to constantly maintain the full "refueling" of the barrels, the water will constantly heat up, you do not have to finish the process of receiving the soul due to the lack of water. Another plus "automation" - the likelihood of water overflow is eliminated. The mooring of the soil near the shower cabin is undesirable.
You can find a proposal for the shower water to select from the container using the float. The end of the flexible intake hose is fixed on the float (you can take a piece of foam of the corresponding sizes), as the water is spent, the float will be descended, the fence is always made from the top, warm, layer. Such a device gives effect, but it is insignificant. The fact is that water in tanks is heated from the walls, hot climbs up, cold drops down. The movement of water in volume is almost constant, which means that there is a big difference in the water temperature in the tank depending on the height.
Another improved is to make electric heating, which will allow having warm water regardless of weather conditions. Yes, the water will be hot, but only who can venture to take a shower if low temperature on the street? But this is not all problems. During the electrical heating device, PUE rules should be strictly observed, and they make very stringent requirements for such work. In addition, it will be necessary to install the power on / off automatics. Do you need such "difficulties" in an ordinary shower in the street? If there is a need to use the shower in the cold time - do the shower in the cottage. This decision will have to be taken in the event of a long stay at the site.
If your shower is attached directly to the tank (there is no shower hose), then a complex of additional measures to its reliable fixation should be taken. With the help of stops (wooden or metal), secure the nozzle, exclude even the theoretical probability of oscillations during the use of the tap. The crane is better to install a valve type. It has a much easier rod running, the water pressure is gradually adjustable, the working surfaces are not oxidized - the smoothness of the stroke does not change over time.
During the construction of the shower cabin, provide an extension to her small additional premises. They can be used both under the expansion of a shower or a device near her one more and for a separate locker room.
A wide selection of both the price and performance characteristics Allows you to choose the optimal option, taking into account your own preferences and the individual characteristics of the country area. Industrial showers can be completely plastic, metal with trim various materials or awned. Completed with water tanks, cabins (metal or wooden), pallets and material of the trim.
Shower for giving plastic 
According to consumer reviews, it is quite convenient to use the cabins, but there are several significant drawbacks. Plastic cabins do not meet the required indicators of strength, if children are present in the country, the season of work without repairing such a design will be great.
The second drawback is a high price. A shower cabin made by hand will cost an order cheaper. There are quite cheap options for industrial cabins, but in terms of strength indicators, they can be attributed to the category of "single-room". You should not throw money, you can independently build a wonderful, solid and reliable shower room for this money.
Street shower "Economy" 
The third drawback - mass production is calculated for the average user. It is natural, all work on such a scheme production companies. By creating a booth with your own hands, you can do all calculations for yourself, change the location of the soul, its height, the dymeter of the drain holes, the adjustment mechanisms, etc. In addition, there are no restrictions on installing additional equipment, change in height and width. Devices of additional decor elements. There are masters manufacturing very original showers.
Everyone country plot Requires constant improvement, do these affairs. You can start with the shower cabin, then build a gazebo, then the bath and so on, from simple to complex. You will see for personal experience - no better than what is done with your own hands.
After a hard work day on Earth, I sometimes want to clean my body from dirt and refreshing in warm water.
If nearby is suitable for bathing with water, it is good. And if not, the time to think about the device of the summer soul in the country area.
There are two types of this facility:
A shower cabin with a tank can be purchased in the store. Its value varies from 5,000 to 18,000 thousand rubles depending on the materials.
Such a soul will last much longer and water in it will heat up faster and keeps the heat of interest. For the shower construction, the square of the square shape is suitable. It is more stable, spacious.
In addition, this form accelerates water heating. The tank size depends on the number of people who will enjoy them during the day. But remember, the greater the tank, the slower the water heats up in it.
Now consider the stages of the preparation and construction of the summer soul with heating water.
It all starts with the choice of a place where the shower will be. It must be protected from wind and the most accessible to the sunshine.
The first condition is necessary to prevent the possibility of catching out due to draft after the taking of the soul.
Second - so that water warming is more efficient. Even if you design a shower with artificial heating, natural will help reduce energy consumption. And an important factor - the shower is better to set close from a reservoir or water intake crane.
Deciding with the place, it's time to think about the size of the structure. The standard is considered a soul of square shape with walls of one and a half meters long and a little more than two meters in height. But if there are complete or very tall people among potential users, in the design of the cabin it is necessary to take into account.
An important factor - what materials will be used in the construction. You can use a frame of wooden bars. It is environmentally friendly, but not very durable.
Therefore, the soul frame is preferred from a metal, and everything else is from a tree. In this case, you should prepare the kits tool for work and with metal, and with wood.
The last moment to be thought out before starting construction, is a draining device. There are several options. The simplest thing is that water goes into the soil under the booth.
It is not quite convenient because you have to leave the gaps between the boards in the floor, and this in turn will lead to drafts in the shower. A more common option - draining water in specially dug cesspool pit or septic tank.
To do this, the pallet is installed on the floor of the shower cabin. It is specifically set with a bias so that the water used is not stored and did not require additional efforts to clean up after taking the shower, and the pipe or the hose is drilled below, the other end of which is sent to the pit.
Construction begins with the installation of vertical racks. If the soil is not distinguished in the area of \u200b\u200byour country area, then it makes sense to build under each standing rack.
The frame of the three walls can be strengthened with the help of transverse beams. So you can be sure that the design will not fall apart in a couple of years under the weight of the tank or something else. And on top you need to equip a platform for water tank.
The covering is performed by the already prepared material in two layers (external and internal), between which, at will, the insulation is placed.
This additional layer is necessary if you plan to use a shower in spring or autumn, when the weather is not warm enough. After completing this part of the work, the door is hung.
The conclusion is to install the tank. First, the heating element (TEN) is installed inside the metal brackets, and so that it does not touch the walls. Then the hose is supplied to the Baku, equipped with a water intake crane, and an electrical cable is connected to the tane.
All this now should be installed on the cooked area on the roof and secure metal cables. From above you can construct the semblance of a greenhouse: pull the film (preferably dark color) On wooden bars.
So heat will be attracted and at the same time not to go out. At the final stage, it is worth checking the tightness of the system again, if necessary, use rubber gaskets or silicone seals.
With a limited time or means, you can arrange an extensive version of the soul. It is arranged near the wall of the country house, to which the water and shower capacitance is attached. The walls of the shower are replaced in this case with curtains from tarpaulin or cellophane attached to an easy wooden frame.
The cottage always combines a place and work, and rest. Therefore, make sure that the working conditions are comfortable, and the resting place is pleasant. And the summer heated shower will help you with it.
Nothing is so relaxing after a hard work day in the country, like a summer shower. Water not only soothes, but also refreshes, distracts from unpleasant thoughts and removes tension. But what to do, if there is no soul on the soul? If there is no desire to splash in a trough or pelvis, you need to take care of the comfort in the field and construct a refreshing summer shower for your favorite giving with your own hands using ready photos and drawings.
Summer shower takes one of the first places among all country buildings. Sometimes it is not easy way to wash after the day came to the end, dedicated to the cultivation of the Earth, but also the only way to refresh yourself in the heat.
For the construction of the summer soul, choose a place well lit by the sun First you need to choose a place to install a shower facility. To do this, explore your site for secluded places.
On the other hand, this place should not be far from the main building so that you do not have to freeze on the way to a warm house, if you decide to take a shower in a cool day.
Tip! If the heated tank is envisaged, make sure that nothing shads the water tank.
After you have found a suitable place, select the best sizes for your cab. Note that a person is required for the convenience of movement at least 1 m 2. If a pre-tribbon is planned for changing and storing dry things during swimming, the construction increases by another 60-70 cm. The height of the shower cabin is about 2.5 m. So, the estimated soul dimensions for the cottage 170x100x250 cm.
Scheme: Construction of a summer shower cabin of polycarbonate If the design is assumed to be wooden, then the next stage of construction will be the construction of a frame from wooden bar or metal corner.
Next - walls. Note that for better ventilation, the walls must retreat from the ceiling and a pallet at least 20-30 cm. The walls are built mainly from those materials that remained during the construction of the main country construction.
When installing a shower for giving with your own hands, it is necessary to provide a supply and draining of water in advance. The drain system is laid at the construction stage of the foundation, and is organized during the installation of the tank.
