Large equipment and compact water heating devices are actively involved in the formation of comfortable conditions. Few citizens know how to use the water heater, because Their apartments are connected to centralized DHW. However, if you have to live in a Khrushchev or in the country, information about the operation of not constant aggregates will be extremely helpful, agree?
You will receive reasonable answers to all the questions that arise when using devices. In the article proposed, the article is thoroughly disclosed by the theme of water heaters, their species and structural features are indicated.
In detail the specifics of the installation and the rule of competent operation. Indicated technological subtleties and nuances of care. To facilitate perception, information is supplemented with photos, schemes and video guides.
Flowing models warm water from the tap pipe immediately after the crane is discovered. Visually, such models have significantly smaller sizes and are mounted next to the crane.
A variety of flowing water heaters is a special crane. It requires not much electricity and can be a real find for the cottage
Depending on the fuel consumed, the most often accumulative and flow devices are:
The first have a greater initial value, but payd back in 2 years. The second initially cost is cheaper by 2-3 times, but through the high-cost of electricity for the third year of use is expensive for its owner.
This dependence is valid for continuous use.
Flowing models of heaters can be equipped with kitchen spill, shower. They are mounted next to the crane to avoid big heat loss
If we are talking about a seasonal stay in the country and the use of small amounts of warm water, then the potential buyer is suitable for the potential buyer as it is impossible.
After all, electricity is supplied to many country sites, and as for gas, the situation with its accessibility can be paying. And with rarely use of the device, it completely spends electricity a bit.
Regardless of the type of the acquired device for heating water, it is necessary to handle and use it to be used to use it. Moreover, the features of operation in all the same type of models are similar, but there are also fundamental differences.
In order for its ignorance not to harm the expensive instrument, it is better to read in the instructions, how to properly use a specific water heater model.
Differences in appearance And the device in flow and accumulative models cause some nuances during operation.
Therefore, before using the unit, it is important to carefully examine the recommendations specified by the manufacturer.
Flowing Crane Water heater can be used not only in the country, but also in the conditions of the urban apartment. It is easily installed and connected with his own hands.
The most common demands that need to be performed before the start of operation of cumulative and flow models are as follows:
The horizontal location is checked construction level. Clear adherence to this rule will help prevent the formation of air traffic jams.
It is also important to take into account that there are models that can only be installed horizontally or only vertically. If you neglect by this rule, the equipment will not work at best, and at worst - simply burns.
Small models of flowing electric heaters vertical execution Easily fit into the kitchen design. Yes, and a lot of space is a 10-liter device will not take
There are also models involving the installation option to choose a user - horizontal or vertical. The structural features of the device are designed for any position and will not affect further operation.
Flowing water heaters produce many domestic firms. Also on the market you can find a large number of proposals from European and Chinese companies.
Cumulative water heaters are like a horizontal type and vertical. Moreover, this rule concerns not only small bulk boilers
Many manufacturers offer accumulative models that require gas or electricity to work.
The first option with a constant use of a family of 5 people with a duration of 4-5 years will cost under the total purchase costs, the connection and payment of the gas is 3-4 times cheaper electrical option. Although, the cost of the aggregate itself in stores is 2.5-3 times cheaper gas device.
You can only operate a boiler, which is properly installed and connected to the power supply network. A specialist who has conducted all work is obliged to put a mark about this in a warranty card and test the quality of installation of equipment.
Without his signature and printing, the organization fails to take advantage of the guarantee.
If everything is set to a responsible master, the owner can start exploiting the water heater. First, it is necessary to examine the equipment from all sides and make sure that all the whole, there is no visible damage, the wire with the fork has not been melted anywhere and does not flow anything.
If a visual inspection has passed successfully, you need to fill the boiler or make sure that it is filled. To do this, open the water supply valve to the unit and unscrew the crane of hot water. As soon as water begins to flow from the crane - the cumulative heater is filled.
Now you can turn on the instrument plug into the socket and press the "ON" button on the case. Management and adjustment is carried out by the corresponding buttons.
Depending on the equipment model, the control and adjustment of the desired temperature can be carried out by mechanically or by making the appropriate commands on the monitor.
Technical excellence of the device directly affects its value. In everyday life, models are bought with the most necessary features and simple control. The simpler, the less damage in the future.
You can use information about the independent, discussed in another article.
In practice, electronically controlled water heaters are poorly tolerated in the bathroom. It is advisable to avoid installation indoor with high humidity level
It is important to operate all the rules described by the manufacturer in the instructions for a specific instrument. Also, in no case do not include a broken heater.
If the external condition causes concerns or seen melting tracks on the wiring or fork with an outlet, must be addressed to those skilled in the art.
If the cumulative unit is the main source of hot water in the house / apartment, then, in order to save, it is not worth it from the outlet.
Thanks to the installed thermostat, the device will turn on the heated water only if necessary. Once the water reaches the desired temperature, an automatic shutdown will occur.
Such work allows you to make the most economically use electricity or gas, if it is a gas water heater. It is advisable to turn off the equipment only in the case of a long absence of the owner and all residents of the house, cottage or apartments.
Gallery of images
Trading Mark Polaris on the industrial market has existed since 1992. Today, the company takes a niche of international manufacturers of household appliances, since it has production units in four countries. The range of corporate products includes a variety of household equipment, including the Polaris water heater.
Name trade Brand Polaris occurred from the name of the polar star. The concern was formed in the 92nd year, in October. It was then that the small group of graduates of the Moscow Aviation Institute decided to open a private company for the manufacture of televisions. The first models equipped with remote controls were made on Philips lines. But in 2003, the first its own production factory was included in the work, which is located in the Kaliningrad region.
The company regularly found new household equipment manufacturers to establish partnerships. So she could significantly expand product range. Under this trademark, more than 700 varieties of equipment are performed, for example:
The department of engineers and designers lead work on the creation of new series of goods, taking into account the needs of the modern consumer and innovative technologies.
From the entire range of proposals, the owners of water heaters Polaris determined the rating of the best variations that deserve consumer attention.
The cumulative electric water heater polaris has a lower liner and is installed in a vertical position. The model has a pressure supply system, therefore it involves connecting to several water points.
POLARIS AQUA IMF 50V
The tank accommodates the water of 50 liters, Polaris is able to warm up the contents to a temperature of 75 ° C. There is protection from inclusion without water and overheating. The inner part of the tank is covered with stainless steel, and the power of the TEN is 2.5 kW. Cost cumulative water heater Aqua IMF is 14000 rubles.
Video: Overview of the work of Polaris Aqua IMF 50v
The accumulative Polaris heater for 80 liters has a maximum power of 2.5 kW, but it has three heating modes. In the manufacture of tank of the accumulative electric water heater, POLARIS used a special tungsten coating of the joints to increase the degree of reliability and operational period.
POLARIS ULTRA IMF 80 V
The design has a copper heating element, as well as three levels of protection against leaks and overheating. The size of the water heater Polaris Ultra IMF 80 is equal to 67x46.5x34 cm, weighs the model 10 kg. The price of the device is 17,000 rubles.
Video: Overview of work and installation rules POLARIS ULTRA IMF 80 V
Electric flowing water heater Polaris Mercury will solve the problem of organizing autonomous water supply in any house. The power of the model is 5.3 kW. The configuration contains instruction manual, shower nozzle, hose.
POLARIS MERCURY OD 5.3
The installation of a flow-type water heater is made by a vertical method, and water pipes Complete to the equipment below. The fully empty apparatus weighs 3.1 kg, its performance reaches 4 l / min., And the maximum temperature indicator is 55 ° C. On the control panel, you can choose 1 of the four modes of operation. The cost of the flow of electric water heater is 5000 rubles.
Video: Overview of the work of Polaris Mercury OD 5.3
Polaris water heater has a capacity of 2 kW. Water enters the intake points under pressure to 8 atm, so that the device is allowed to connect to several plumbing outputs.
Polaris PF 50 VR
There is a thermometer and temperature limiter, as well as a mechanical control system. Installing Polanis 50 liters with a vertical method and is fixed on the wall surface by the brackets. As a heater, the model uses a copper tan, not subject to corrosion. Price - 7900 rubles.
Video: Overview of POLARIS PF 50 VR
This is a wall-mounted compact heater with a capacity of 3.5 kW. The design is there a thermometer, starting indicator, heating, temperature limiter and safety valve. Electric flowing water heater has a rounded form and dimensions of 25.7x38.7x8.4 cm.
Polaris Ultra 3.5
On the front panel there is an information display that informs the user about the specified mode of operation. Weigh the device 3.4 kg. Cost - 3900 rubles.
Video: Overview of POLARIS ULTRA 3.5
The accumulative electrical apparatus per 100 liters is able to warm up water to 75 ° C. There is a digital display and an electronic control system. The configuration provides for a stainless steel tank, in this model there is an anti-corrosion anode and a start-up indicator.
POLARIS GAMMA IMF 100 V
The device with dimensions 55x88,5x37 cm weighs 20.4 kg. The Gamma model has overheating protection, safety valve, as well as the function of accelerated water heating. The device is installed on the wall in a vertical position with the lower lining of the water supply system. Price - 14,500 rubles.
The accumulative water heater with a volume of 50 liters and a capacity of 2.5 kW involves working for several points. It presents a mechanical control system, start-up and heating indication, the accelerated warming function, the thermometer, information screen, the temperature limiter.
The security system includes protection against overheating and one anode. Cumulative capacity consists of stainless material. The device is installed in a horizontal position on the wall, and the pipeline is supplied to it from the bottom. The dimensions of the model are 80.9x45x24.8 cm. The cost of the accumulative water heater Polaris VEGA IMF 50H does not exceed 17,500 rubles.
Malfunctions extremely rarely arise by themselves, if it comes to a factory marriage. Technically, good equipment can be output in several cases:
Video: Water heating tank repair FD -100V POLARIS
If there was a need to purchase a high-quality water heater for home or giving, then you should pay attention to the model from Polaris. This company represents a wide range of devices, among which you can easily find the desired option.
The devices of this brand are manufactured with different, but convenient control. Some models are equipped with mechanical control, and other electronic and even differ in the presence of the display, which displays all the necessary information.
Also among the technical characteristics of a model, it is worth paying attention to the presence of a thermostat and power levels.
It is worth noting that all Polaris models have reliable protection, which is guaranteed to ensure uninterrupted and durable operation of the water heater. All devices necessarily have protection against overheating and automatic shutdown. That is, if the device is very hot, work will stop automatically, without allowing the water heater to spoil.
The magnesium anode allows you to prevent corrosion of the inner walls of the tank, so that it will last much longer.
In addition, the models of this brand are produced with dry ten, which is very reliable. The fact is that the heating element of the device is under reliable protection, is located in a hermetic flask and does not contact directly with water.
Each model of boilers from Polaris has many advantages about which it is worth telling more detail.
Despite all the advantages, Polaris water heaters still have some minuses.
Consumers who already use the devices of this brand noted that some models are too bulky and heavy. Of course, it is minus, especially if the house is thin walls. It is worth considering this fact during installation. If there is no confidence in the reliability of the walls, then you will need to take care of additional security and the fastener system.
In addition, among the shortcomings, consumers celebrate a high price for some models. Therefore, before laying out a large amount for this or that model, you need to know what its advantage over more budget options.
More budget optionsUsually differ in tank with thin walls, which, of course, is a disadvantage. Such models will not be able to serve too long and there is a risk that the device will soon begin to leak. Specify all the nuances before buying and be sure to purchase a model with a guarantee.
Flowing models often have such a deficiency as the maintenance of only one point. It is not very convenient, especially if hot water is needed in the bathroom, and in the kitchen. In addition, such models can work properly and smooth if there is a good water pressure in the house. Otherwise, interruptions will begin.
Polaris water heaters are different species and volumes. There is a flowing water heater, and there is a cumulative. The volume of tanks is also different. It can be 10, 30, 50, 80, 100 liters and even 150.
Cumulative water heaters from this company are produced by a volume of 10 to 150 liters. As a rule, such models have perfectly withstand pressure up to eight atmospheres. The design of such devices also has its own distinctive features. For example, cumulative models can easily be connected to a normal outlet, which is quite practical.
Many storage models from Polaris have the ability to connect immediately to several points, which allows you to install one water heater in the house for all water intakes.
As for the time that goes to heating, it all depends on the model and volume of the tank. Usually, the first heating after installing the water heater leaves at least half an hour. After the TEN will turn on when the water temperature is falling. Thus, in the crane of your house there will always be hot water. Another method of heating helps to save electricity.
In addition, the accumulative tanks are equipped with high-quality heating elements and have excellent thermal insulation, which makes the water as quickly as possible and retain it for a long time.
When choosing a cumulative model, it is worth considering the fact that you need a separate place to install it. If you need a water heater only for washing or washing dishes, then the tank of 10-15 liters is the best way. For regular taking a shower, the volume must be at least 30 liters, on average - 50. And for those who are used to often take the bath, it is worth purchasing boilers with a volume of 80 liters and higher.
Another type of water heater is flowing. His main difference is that it is capable of almost counting water to heat water to the desired temperature. Cold water before getting into the crane, passes through the heating element and, immediately heating, pours out of the shower or crane.
Flowing models are divided into two types: pressure and non-free. The first option is in great demand. Such models are mounted in the risers themselves, which saves space in any room. The only minus is that they are much more expensive non-free.
Flowing water heaters, as a rule, differ in their compactness. Most often they are installed in the kitchen.
All models from this company from the first sight attract their design. For example, there are flat models that look perfectly in the interior, becoming his bright detail. You can also choose a compact option, for example, a volume of 15-20 liters.
It often happens that due to long or irregular operation, the boiler fails. Accordingly, the device is required. Before calling a specialist, it is worth determining the cause of the problem, because often many problems can be eliminated with their own hands. But someone can safely remove the control panel, disassemble the device and eliminate the problem, and someone does not even know how the temperature indicator is replaced.
Usually, water heaters are faced with the following problems:
Operating instructions are included in each instrument. As a rule, there are the most common problems that can be easily solved by following step-by-step instructions.
Water heaters "href \u003d" / text / category / vodonagrevateli / "REL \u003d" BOOKMARK "\u003e WATER HEATER . We are confident that you will be pleased with the acquisition of the product of the brand "Polaris".
Before starting the instrument, carefully read this instruction, which contains important information regarding your safety, as well as recommendations for proper use The device and care for it.
Save this instruction along with the warranty card and cashier check.
Purpose and scope· Electric accumulative water heater is designed to provide hot water supply apartments, cottages, baths and other household premises.
Safety requirements· The manufacturer warns that the improper fulfillment of the requirements of this instruction, as well as unauthorized "improvement" of the design of the device, can lead to the consequences dangerous to the health and life of the consumer.
· Electrical connection must be performed according to electrical schemeshown below.
· Safety valve that is included in the package cannot be drowning or replaced.
· Installation and connection should produce specialists who have the necessary qualifications.
· Attention! It is forbidden to install horizontally vertical water heaters, and vertically horizontal .
· The hoses and connections connected to the water heater must withstand the operating pressure of up to 6 bar and the temperature to + 80 ° C.
· The device must be grounded.
· If the device is not used for winter period (For example, in the country), in order to avoid the destruction of the product due to the expansion of water during freezing in the water heater, all the water from the device should be drained.
3. Technical description
1. The temperature adjustment is carried out within 35 ° C - 75 ° C with a digital display of the temperature of the heated water.
2. The device can be used in wide ranges of water pressure values \u200b\u200band its volumes; It is capable of providing simultaneous several consumers.
3. The inner walls are made of high-quality stainless steel.
4. The device has good thermal insulating properties, which allows to maintain a temperature for a long time.
Protection against water pressure drops (with water pressure exceeding 6 bar, automatic pressure reset occurs). Overheat protection. Thermometer, thermostat and bipolar thermostat built into the water heater.
During operation, the water heater tank is constantly under pressure from the cold water highway. Water heats the heating element at the bottom of the tank. When consuming hot water, cold water entering the lower part of the tank, displaces the heated water through the hot water fence tube at the top of the tank in the hot water distribution highway.
When a given temperature is reached, the electronic thermostat automatically turns off the heating element. The electronic thermometer shows the water temperature in the tank. When the temperature is reduced, the water heater is automatically turned on.
For proper Installation And the product is properly the following information.
1. Device and part name
2. Basic specifications and electrical scheme
3.1 Installation Requirements
3.2 Fastening method
3.3 Preparation and Connection
3.3.1 Connecting to the water supply system
3.3.2 Electrical connection
4. Use
5. Moments requiring attention
6. Service
7. Set of delivery
8. The most common faults and their elimination
9. Service life
10. Warranty
1 . Device and titles of the main parts
Left cover front panel insert drain hole hot water output Cold water electric cable right cover display magnesium anode brackets rear panel
| ||||
Stream 5.0 - 30 H | ||||
Stream 5.0 - 50 H | ||||
Stream 5.0 - 80 H |
Div_Adblock5 "\u003e
| Nominal voltage | Nominal | Rated power | Maximum pressure |
||
Stream 5.0 - 30 H | ||||||
Stream 5.0 - 50 H | ||||||
Stream 5.0 - 80 H |
3. Mounting
Installation of the device is made by the buyer at its own expense.
The manufacturer is not responsible for the problems caused by improper installation and dismissive attitude to the recommendations of this manual, namely:
a) Electrical connection must be performed in accordance with the rules of section "3.3.2 Electrical connection".
b) Safety valve included in the package cannot be drowning or replaced.
To reduce heat loss along the length of the pipes, the device should be installed as close as possible to the place of consumption of hot water. To facilitate the care of the device, leave a place for free access to electrical parts (approximately 0.5 m). In addition, it is recommended to install the water heater at a distance of 20-25 cm from the ceiling and adjacent walls.
3.1. Installation requirements
§ Despite the fact that the device has good protection against current leakage, we recommend installing a protective regulator on the power chain (RCD) and ensure reliable grounding.
Electricity sources designed for 220 volts and 50 Hz are used.
§ Nominal values \u200b\u200bof the current for the protective regulator on the power circuit must be no less than the current values \u200b\u200bfor the water heater.
§ Follow the cleanliness of the protective regulator on the power circuit in order to prevent current leakage.
§ On the dummy opening of the cold water receiver, a safety valve must be installed.
§ Drain tube, installed on the pressure reset valve, must be drawn down and be free.
§ The wall, to which the heater is attached, should be durable. If the wall does not withstand the dual weight of the heater tank filled with water, then the consumer must install support under the bottom of the heater.
§ At the place of fastening the heater should be provided for the water for water.
3.2 Fastening method
1. Select the appropriate place to install the water heater. In accordance with the markup shown in Figure 1, using the drill with a diameter of 12 mm, drill four holes in the overhaul on one line.
2. Insert the dowels in the holes and secure the bracket on the wall using screw screws. (When installing a water heater in a wall niche, use the dimensions indicated on the diagram on page 5).
3. Take the water heater, securing it on the brackets. Make sure that the screws are firmly tightened and the water heater is securely fixed.
4. The heater must be attached in dry darkened places, in order to avoid heat loss, the heater must be attached in a place in the maximum proximity to the water supply.
3.3 Preparation and Connection
3.3.1 Connecting to the water supply system :
1. The hoses and connections connected to the water heater must withstand the operating pressure of up to 6 bar and the temperature to + 80 ° C.
2. With a standard connection, the water heater operates under pressure determined by pressure in the highway.
Connecting the water heater input pipe to the water supply system is carried out through the safety valve included.
 |
To avoid breakdown when screwing the safety valve, do not use much effort.
Safety valve performs two functions:
Passes water only in one direction
(is the check valve).
With a pressure above 6 bar, water blends through the hole on the side.
(calibrated on 6 bar).
The appearance of water droplets from the hardening valve during water heating is a natural process and is associated with the expansion of water in the tank when heated. The valve hole we recommend connecting the tap flexible tube with a drain system.
In no case cannot close the valve hole!
If the water pressure in the highway exceeds 5 bar (atmospheres), follow the pressure reducer after a water meter.
Connection diagram for several taps
Connection diagram for one conclusion
3.3.2 Electrical connection.
1. It is necessary to ensure reliable grounding.
2. Use energy sources with voltage 220 volts and 50 Hz
3. For the water heater connection to the electrical network, you should use a two-pole switch (preferably an automatic) with a distance between the contacts of at least 3 mm.
4. In the circuit of the power supply, install the protective shutdown device (UZO). Contact advice to a qualified specialist.
Make sure that the voltage in the network corresponds to the value indicated on the marking plate (nameplate).
UsingImmediately before turning on, fill the water heater with water. To fill the water heater with water, you must open the overall valve of the plumbing and the valve of the hot water. The device is completely filled with water when it is completely power out of the valve of using hot water.
Attention! Only when the device is filled with water completely, you can include in electric network heating element .
After filling the water heater, close the crane of hot water, inspect the machine and make sure that it does not proceed. Turn on the water heater to the network.
1. Turn on the temperature controller control buttons:
temperature adjustment "(left) and" Enable - Disable "button (right)
The "Temperature Control" button is used to control and set the temperature.
The "Enable-off button" is used to start and stop the heater.
b) Digital display (double-digit, eightpositional): Used to display temperature adjustment and its real values \u200b\u200b(00 - 99), issuing warning signals (E2-E4)
c) Standby: The heater is in the on state, but the heating is not performed. The pointer displays the current water temperature indication.
d) Turning mode: Turning on is made by pressing the "Enabled" button, the display shows the value of the previously set temperature (if the temperature is not installed, the initial temperature is displayed in 750c). If in 5 seconds, the water temperature is adjusted, the water heating temperature will be installed on the display and its heating / maintaining a given temperature will begin.
If the water temperature is lower installed, the heater continues to work.
If the water temperature is higher than the installed, the heater stops working, and the system switches to the mode of maintaining the specified temperature.
With the mode of maintaining a predetermined temperature, when the temperature is reduced, the heater turns on 50s.
e) Maintaining the set temperature: The heater is in the on state, click the "Temperature Adjustment" button, the display shows earlier set temperatureBy pressing the button, go to the operating mode, the set value will turn on the display, then each pressing the temperature button will increase by 50c. The temperature change sequence looks like this:
35→ 40→ 45 → 50 → 55 → 60 → 65 → 70 → 75→ 35
If for 5 seconds after stopping the adjustments, stop pressing the button, then the value is set and return to the initial position.
e) When you press the "ON - OFF" button again, the heater switches to standby mode and display the temperature of the water temperature on the display.
2. Overheating protection:
If the heater stops working on the state and goes into prevention mode, then it further work It is possible only after troubleshooting.
a) Insufficient water level: If during checks the temperature in the heater for 7 consecutive inclusions increases by more than 20 s in 4 seconds, check the water level in the heater. In this case, the "E2" mark appears on the display screen. When it appears, it is necessary to turn off the power heater and after filling the re-test.
b) Temperature sensor fault: When the temperature sensor is closed on the display screen, the "E3" mark appears.
c) Temperature readings fault: If the temperature is exceeded during control, the "E4" mark appears on the display screen. Disconnect the power and check. If a safety device is turned on when overheating, it is impossible to automatically run. Repairs must be made in a specialized workshop.
3. With a water pressure of less than 6 bar on the safety valve may occur. This is a normal phenomenon.
4. If you do not use the heater for a long time, overcap the cold water supply valve and disconnect the device from the electrical network.
5. Moments requiring attention
1. When you first use the heater, full removal of water from the tank and remove detachment, make sure that the device is filled with water and only then take it on to the network.
2. If the power cord is damaged, it should be replaced with a special cord or kit, obtained by the manufacturer or its agent.
3. Winter and in cold areas with long-term non-use of the heater, descend water from the heater. To do this: Close the cold water supply valve, open the drain valve on the safety valve and open the hot water fauce on the mixer, then drain the water.
4. Do not use plastic and aluminum hoses as applying pipes.
5. A real electrical heater requires safe and reliable grounding.
6. A safety valve must be installed on the electric heater dummy tube.
7. The fuel and drain holes of the heater cannot be simultaneously closed.
8. The outer cross section of the water heater electrocable should be at least 2.5 mm2, and the current current leakage control must be calculated for the current of at least 25 A.
9. This type of electric heater is equipped with electrical cables that do not have connectors, so to connect to power sources, use switches providing a reliable interrupt (for example, switches or interrupters, the distance of the interrupt point should be at least 3 mm).
6. Service
During the operation once every six months, clean the heater.
Sequence of actions: Disconnect the water heater from the network, break the water tap, open the drain valve, turning the handle, open the drain hole (be careful and do not scatter) and drain the dirt.
In the presence of strong formation of scale in heating tubes or a large amount of precipitation, remove the heating tubes and clean them. With them reverse installation Observe the following: Tightening bolts should be carried out evenly, without a significant application of force, the fixing support should not be inclined. Connecting the power supply can only be produced after filling the product with water. With long-term non-use of the heater, overcap the cold water supply faucet and disconnect the water heater from the power supply. With a water pressure greater than 6 bar, water drops may appear on the drain hole of the safety valve or leak.
a) A rare appearance of water droplets on the drain hole of the safety valve means the normal operation of the heater. In order to further exclude the appearance of water droplets on the fastener of the safety valve, keep the cold water bay valve open.
b) Frequent appearance of water droplets on the drain hole of the safety valve means that water pressure exceeds the norm. In this case, on cold water supply pipes, it is necessary to establish a pressure relief valve, which should be located at the maximum distance from the heater.
c) to remove the resulting droplets of water, it can be used by a discharge tube, the end of which should be directed down and not be closed.
d) the approximate service life of the magnesium anode is 1 year, after which it is recommended to replace experts service Center.
7. Set of delivery
1. Water heater - 1 pc.
2. Safety valve - 1 pc.
3. Drain hose - 1 pc.
4. Kit for fastening - 1 pc.
5. Instruction - 1 pc.
The most common faults and their elimination.Type of malfunction | Cause of malfunction | Debugg |
When the power is connected, there are no readings on the indicator screen. | Bad contact or no power supply | Connect to the power supply, check the contacts |
Malfunction of electric hammers | Special type of repair |
|
The heater is not filled with water | Special type of repair |
|
Out of system internal connections | Special type of repair |
|
Special type of repair |
||
Water overheating, turn on the protective device | Special type of repair |
|
No water at the exit | Incorrect connection of supply pipes | Correctly connect |
Shogging valve | Clean the valve |
|
Increased heating time | Strong formation of scale | Spend special repairs |
Heated heating element | Spend special repairs |
|
Fault regulator | Spend special repairs |
|
Lack of water | Set the presence of leakage. |
|
Sensor failure | Spend special repairs |
|
Overheat | Spend special repairs |
Attention:
If such faults occur as a water heater tank leakage, frequent triggering of a protective device and other faults that require a special type of repair, disconnect the water heater from the power source, break the hint of cold water supply and notify the service service. An independent dismantling of the boiler may be carried out only with the consent of the local service center and the seller. Violation of this requirement may result in loss of warranty.
Life time:Mounted by the manufacturer, in accordance with clause 2 of Article 5 of the Federal Law of the Russian Federation "On Consumer Protection", service life for storage water heaters is 7 (seven years provided that the product is used in strict accordance with this Instruction Operating and appropriate technical standards. Please do not confuse the service life with the warranty period. The use of crude water reduces water heaters' service life. After the service life expires, the product is considered unsuitable for use on direct main (or functional) intended purpose and is subject to disposal in accordance with applicable law.
Manufacturer:
Texton Corporation LLC - Texton Corporation LLC
1201 Street Market, Willmington 19801, Delaware, USA
The device passed mandatory certification.
10. Warranty
This warranty is provided by the manufacturer in addition to the consumer rights, established by the current legislation of the Russian Federation, and in no way limits them.
This warranty is valid:
· on bak Water heater 5 years from the date of purchase of the product, provided that the instrument is properly opened *.
* Under the correct operation, it is understood by the conduct of a mandatory annual maintenance and replacement of magnesium anode.
· Electrical and electronic components - 1 year.
and it implies warranty service of the product in case of detection of defects associated with materials and production. In this case, the consumer has the right, among other things, on free repair of the product. This warranty is valid under the following conditions:
The product should be purchased only in Russia, and exclusively for personal household needs. The product should be used in strict accordance with the instruction manual in compliance with the rules and safety requirements. The obligations of the manufacturer under this warranty are performed in Russia by sellers - authorized manufacturer dealers and official servicing (service) centers. This warranty does not apply to products acquired from the unauthorized manufacturer of sellers, which independently respond to the consumer in accordance with Russian legislation. This warranty does not apply to product defects resulting from:
For all questions of warranty service Polaris, please contact the nearest Official Polaris Seller.
Water heaters are a necessary household appliance that helps to significantly ease life. We propose to consider how the water heater is properly connected to the power grid, to the water supply, in the country, as well as the installation of a horizontal boiler in the country and in the apartment and general scheme Installation.
By this way, you can connect the accumulative water heater of ATMOR (ATMOR), Elenberg, Eltron, Etalon, Ferroli, Gorenje, Polaris, Stiebel, Themex, Vega, Termex, Ariston (Ariston), and others. He is considered to be effective option To attach a simple vertical boiler, but first you need to figure out the design of the device.
The standard boiler consists of such parts:
The most important thing when choosing a boiler is a way to attach it to the wall (vertical or horizontal), and the volume of the tank. Most often B. modern apartments It is vertical appliances: they occupy significantly less space than horizontal water heaters and are connected to the water supply system much easier and faster.
Step-by-step instruction:
A fuse or a protective valve is a special device that serves to protect the tank from breaking at very high temperatures or pressure. This may occur if the fluid pressure in the tank exceeds the nominal indicator (the standard value is 0.6 MPa). The pressure valve hole must be open, because often home experts simply forget in time to ensure that there is an extra hot water into the sewer, which is exposed to their seven serious danger.
It must be said that the standard valve in a set with a water heater most often simply does not cope with its task, and we recommend immediately buying a protective device separately, already providing the needs and capabilities of the boiler.
Installation of an outdoor or horizontal boiler does not take much time, but this is a very surround job. They are often more than 50 kW with power, and they weigh about a hundred kilograms, so they are difficult to transport or simply move on their own. The system is connected to hot and cold water in the same way as vertical water heater Only with the difference that the drain hole is located on top.
Video: Water heater mounting
The grounding system is also more serious, a separate conclusion is envisaged for powerful boilers. It can be easily made with your own hands, just branched the wire from the iron part, and connect it with an independent output to the ground.
This device is mainly used in production, because He has a fairly large volume, and the price is high - from 80,000 rubles (the cost was taken into account by the regions of Ekaterinburg and Moscow).
As you see connect flowing water heater - This is a simple task that requires maximum concentration of attention. If it is incorrect to attach a coupling or weakly tighten it, then the breakdown is inevitable, due to this, the service life can also significantly decrease.
No special documents are needed if you buy a water heater, and not a gas column.
The size
Parameters
