The sight of the interior is now presenting high demands. The owners of Khrushchev, admirable repeatedly paper chopers in their apartments, are no longer solved to start repairing their own hands. They do not know how to glue the wallpaper in the corners so that the room looks at the proper level. With vinyl and fliesline canvases work harder. They are heavy and require certain skills. If you correctly close the corners with wallpaper, then the next repair will not be soon.
How to glue wallpaper in the corners?
Move perfect two planes together is difficult. Therefore, even with smooth walls, the angles have a mass of deviations. I had a lot of work and Vadik was to independently separate the apartments of the aunt. He did not decrease to start, because he did not know how to properly glue the wallpaper in the corners.
Glue wallpaper in the room
I decided in practice to show a friend of the wake of the rooms of the old houses. One of my brigade made apartment repairs in a historic building. Vadik could see:
Corner finishing technology with wallpaper of all species is the same. Only thin paper chopers and fiberglass cobweb can be different. Work should be started from entrance door Rooms when sticking jack. When applying the edge of the strips of thin chopper - from the window.
Right glue wallpaper in the corners
Making repairs in old apartments, I always put the walls and install perforated corners. They simultaneously serve as beacons and protect the protrusions from destruction. I choose cardboard if the internal angles have small irregularities. In all other cases, I use PVC profile.
If customers do not want to spend money on alignment and corners, then I simply close up a big depression. I rinse the angle with wallpaper, cut off the band with a width of 10 - 12 cm. I place it evenly on both walls, I do cuts for tight fit. After that, glue the wallpaper in the corners is easier. If the upper cloth has to be cut or paper tapers burst, then thanks to the background from the same material it will be unnoticed.
Independently glue wallpaper in the corners
Tip! It is better to align the corners once again than each time it is overwhelmed the heads of the room.
We make the protrusions
The last strip in the angle is trimmed with the calculation of approximately 2 - 5 cm on another wall, depending on curvature. The more differences, the wider go. It must completely overlap the most convex place at least 8 mm.
For a better fit, I make notches with a sharp knife or just cuts with scissors. It is desirable that they are inclined towards the edge. I close the walls and smoothed at first the main part, then the strip around the angle.
How to glue the wallpaper in the corners of the apartment?
Before starting to stick the wall from the angle, measuring the width of the trenches and spend the line vertically in terms of the level. I check the annex the state of the corner. The side surface of the strip should pass along the deep dent. Stick strictly vertically, on the markup. Near the angle the edge falls smoothly. The protrusions are hidden under the wallpaper pasted before.
Wallpaper with a large drawing is better to cut it in such a way that the lines coincide. A small displacement will be unnoticed.
Thick vinyl wallpapers I cut off the line at a distance of 2 mm from the edge of the upper cloth. A sharp knife is strictly vertically cutting both pieces all over. I clean up too much and the canvas lay the jack. For strength, laying a painting grid.
Glue wallpaper in the corners do it yourself
Tip! Use transparent glue.
Start glue from the door
My friend was able to see everything and now sticking wallpapers in his corners did not scare him. Before starting the room decoration, you should spend vertical lines and check the condition of the corners. If not professional level, You can use the load on the thread.
Before glue wallpaper in the corners, make an approximate layout of the layout of the bands on all walls. If a piece of wallpaper is ended near the corner, then immediately shift the first strip. You can start with cut along the strip.
Smoothly glue on the corners
I used to tell Vadik that to create original interior Combining with different patterns and tones is applied. After an excursion to an old building, he expressed the opinion that designers came up with such a reception to hide defects.
Before starting repairs, consider the interior design options with companyon wallpaper. First, the walls are covered with a pattern with a pattern with an approach to the adjacent wall. Then one-photon stripes make up the transition. Reza lines visually will look like smooth corners. Irregularities will be invisible.
Glue wallpaper in the corners
For not having experienced lovers, combination is more affordable than pasting wallpaper with a pattern. At the same time, you adjust the form of the room and increase it.
Date: 05/13/2017
Many people who have decided to make repairs in an apartment or house own hands, It is believed that high-quality sticking wallpaper will not be much difficult. Yes, to some extent, this finishing material is quite practical, but only on flat parts of the walls, which cannot be said about the corners. And how to glue the wallpaper in the corners? Here, with such a question, people who have begun to repair without professional assistance are faced.
It is in the angles of sticking represents a laborious process, it makes it difficult and questioning the rapid completion of the repair. So you should approach this issue with all the seriousness and study with the scrupulousness all the nuances of such an operation, because the bad sticking of wallpapers in the corners can generally spoil the whole look.
How to glue wallpaper in the corners
Wallpapers are and remain the most popular material of the finish of any kind of premises, whether it is a room in the apartment, an office, or a beauty salon. Wallpaper quality varies, and you can meet absolutely for every taste, color gamut and cost.
Sometimes cheap inexpressible wallpapers are so transformed by the room that it seems not almost worse than expensive, that is, on the construction market, the range of wallpapers is different, and there is high-quality and at the same time cheap Material - two in one.
Today, to break the wallpaper do not need to possess professional skills, but you need to know the sweeping system. The walls first need to be aligned around the perimeter, in the corners, and from here there are already problems with non-professionals.
Stowing wallpapers in the corner
It is not recommended to glue a solid strip of material. In the presence of uneven angles, the strip falls around with folds and does not converge on the other. We recommend to leave the protrusion for an angle of 1.5 or 2 centimeters and then the strip will flatly fall. By choosing wallpaper with high density, use a plumb. Give part of the cropped wallpaper with a small naughty on the adjacent wall so that it is the most vertical as possible.
If in places of corners or proximity to them there are switches, sockets, follows before sticking and any construction work Turn off the supply of electricity and remove the covers. Fully stick the material on the convex parts, and then cut the cut, making small cuts.
Getting Started with Wall pastries near the door, it is important to know that the strip of wallpaper should be cut vertically before the start of the frame. Then it is attached along the edge of the wall. Wallpaper protrusions should be cut off.
Fliselin wallpaper - how to glue wallpaper in the corner
Wallpaper sticking should be made according to the existing technology, observing the sequence of processes, as for non-only corners, and in general, the entire calculation of walls of the walls.
The surface of the surface is better to produce professional tools that are sold in the packaging of various prices, but you can also be primed and diluted with glue, but not particularly welcome. Progressing the surface will help you a special roller or a wide brush. Due to the fact that in the corners of pasting is particularly complex, there is such a trouble as a displacement of the pattern. On the walls of the geometry of the picture preserved, and in the corners everything went and now spoils the general background. Therefore, the most responsible approach the inspection of the corners, whether there are irregularities to eliminate them if there is anything.
Preparation of walls under shook wallpaper
After you have saved all smooth surfaces Walls, you have to go to the corners. Now inspect, and noticing irregularities, proceed to grinding - thoroughly ochpatlev. After complete drying of the putty, it is necessary to clean the entire surface with the sandpaper to achieve the perfect smooth surface, so that the wallpaper does not dug in the future.
Now and the corners need to be covered with primer. If you do not possess the skill of spittle, then there is an output, just buy the same type of wallpapers, or with a simple pattern that does not require further docking (paper). So part of the question of how to glue the wallpaper in the corners can be considered disclosed.
After aligning surfaces in the corners, go to applying glue, it needs to be distributed with all thoroughness at the height of the walls, and in the corners most conscientiously, because in these places the wallpaper most often dug. Roller distribute glue through all the length and brush in difficult to reach places.
Applying glue on wallpaper and walls
Finally, we switched to an important part of the o'clock in the corners. The pro is recommended to glue a piece of canvas in the corners, even if a whole piece is perfectly straight. It is possible to explain this by the fact that the likelihood of the occurrence of distortions in the corners is high, and the subsequent sheet does not dock at all, and after drying, folds can be detected. Professionals of room decoration advise the wallpaper canvases to cut so that the next wall moves the side side by 50 mm. Below is a drawing of shoveling wallpapers in external and inner corners.
Do you know: a closer for beginners in this matter is the curvature of places of sticking. Such an eye surface defect may not always be discovered, so the list of instruments will come to the aid: a plumb and the same construction level. They are measured angles before sticking wallpaper.
If there is a completely serious "challenge", it is better to come to the method "climbing" in these places. This method is used for dense wallpaper - vinyl.
According to this method, the material is passed by 50 mm on the adjacent wall for an angle, and the next sheet is glued to the flashes.
Subsequent step: in the middle of the angle is performed by a special construction knife under the level or ruler in the direction from top to bottom down the vertical incision through two layers of wallpaper.
Wallpaper blending scheme in corners
During the entire process, the iron line is obliged to firmly lay down to the corner and be pressed strongly so that there is no slightest movement. Otherwise, the slot shift is provided. Masters recommend using the long metal line, construction levelwho has more weight and is a wonderful press that interferes with movement.
In order to avoid the appearance of folds in the inner corners, it should be divided into two parts before starting the wallpaper shocking. The first thing is to stick the material to the angle of the room, then you need to measure the distance from the last glued piece of wallpaper to the angular bending, and add the docking 10-12 mm to the resulting digit. After one, the prepared part is glued to the wall with a cropped edge on the adjacent angle. Adjust the edges as usual, whether it is upper or lower.
Now, using a brush or a rapid wallpaper, push the inner corner of the room. If irregularities occur, such as material warping, then take a special knife and carry out cuts, while pressing the wallpaper into the wall. Then the next part shove with the glued material with the glued material, tightly at a brush to the wall. At the end, cut the remnants in the place of bending the same knife.
Tip: If you have a carbon inner and middle part, there are small bulbs, while the bottom is littered with a little inside - it is better to put the cut edges of the mustache. When placing the room with dense (vinyl) wallpaper the best way - This is the use of glue with a transparent base in the joint places, such adhesive is suitable for dense materials.
Pocking the outer corners of the room requires in advance to calculate the length of the wallpaper, and so that the canvas are not enough, and it was able to overeat the convex part of the wall from 21 to 25 mm. When glue tight quality wallpaper, know by making light cuts, for smooth strip laying.
How to glue wallpaper in the corners
Thus, on dense wallpaper using the iron line and scissors, excessive strips of material are cut off, leaving the minimum of the edge, whose notice will not be visible under the subsequent web. On top there is a subsequent lane with an adhesive 5-6 mm. If you have chosen smooth wallpaper, then immediately displace them with a roller, and with a convex pattern, the volumetric can be completely slightly passing.
The vertical picture of the wallpaper makes it difficult to stick in the corners, because distortion is particularly noticeable in these places. The pattern with a horizontal position is not an exception, for example, after gluing it can completely shift. To avoid such incidents, it is necessary to make a small launch on the wall in the neighborhood and at the top of the angle to hide the joint.
Tip: The complexity of pasting wallpaper of corners is to comply with the rule - the edge of the plumb broke down exactly, and the other must trim the edge of the angle.
Bloom the wallpaper and at the same time without a pattern shifts without experience, it will not be possible. The main thing is to make it less noticeable, using the instructions provided above.
Repair of an apartment, houses or office takes a lot of time and strength, as well as money if you decide to ask for help for hired workers. But thanks to the above instructions and accurate follows, you can start independent finish, Adjusting the attention and time to study the stocks of the wallpaper in the corners. Please note the presence of defects, do you have smooth walls and spend preparatory work to eliminate irregularities. In addition, in the corners often pass batteries and pipes that interfer the process of pasting, turning the repair in the hassle.
If you come responsibly to perform this task, taking into account all recommendations and rules, then you are awaiting a completely wonderful result, no worse than if the adhesive was carried out by a professional brigade of masters. After completing the work on the finishing work, you will significantly save money. Good luck and good completion of repair in your home!
Modern wallpaper Language does not turn to call a cheap finishing material - vinyl, phliselinine, vinyl on a fliesline basis, textured and painting ... The result of pasting walls you will admire the next 5-10 years. Most often, the problems arise with how to glue the wallpaper in the corners. Let's figure it out together.
Paper wallpaper - perpetual classic repair. Their unfavorable popularity is due to two factors - a small value and a wide range. However, it should be understood that the rolls of paper, no matter how beautiful the pattern they are decorated, remain very short-lived material, and it makes no sense in the hope of long life.
Already in a year-second, they will lose their former attractiveness, and if there are small children or animals in the house, this process can accelerate at times. However, this minus can be used for good when you need to make lightweight repairs in removable apartmentOr when you like to experiment with the interior.
Vinyl wallpaper on paper based - A more durable finish. Facialwhich falls on the bulk of all operational loads, in this case performs a layer of polyvinyl chloride. And he has a lot of positive qualities:
Vinyl wallpapers on a paper basis are an order of magnitude longer. From disadvantages should be remembered about vinyl airtight, however, if you wish, you can find more modern varieties of finishes on the market, which are deprived of this problem. The vinyl rolls are glued on a paper basis as well as ordinary paper wallpapers, so for the majority will not be difficult to shove the canvas without special training.
Just keep in mind that the layer of vinyl significantly weights the weight of the canvas, therefore, the usual wallpaper glue It does not fit here, you need glue for heavy wallpaper.
The fact is that glue is applied only on the wall. There is no need to apply it on the canvas and wait until they absorb it and swell. So that the joints were perfect, very thorough markup is required. Fliseline Wallpaper - Another variety finishing materialperformed only from Flizelin. Wallpapers may have a flat figure, but, as a rule, it is even canvas with interesting drawings. Glue them in the same way as the previous option.
Traditionally, the most difficult places in the process of sticking are corners. In most cases, they are far from ideal, therefore, if you start glued with the angle of the canvas of the joint in the joint, you can get a substantial skewer vertically. Many mistakenly believe that it is possible to avoid the distillations, if the windows or doors, they say, they say, probably perpendicular to the floor as the starting point for the walls of the walls.
However, this is not always like this - check the window and door frames on errors using the most ordinary plumb. It is possible that you will be surprised how you used to get along with such a curvature. The tradition of glue from the window was primarily due to the need to glue paper wallpaper Vanoslest. If you glue them from the window clockwise, the joints of the junction will not be so noticeable. However, in the case of vinyl or phlizelin wallpaper, it is not necessary to do this.
Ideally, if at least one corner turned out to be smooth, you can start from it. But it is best to make a thorough markup around the perimeter of the walls, focusing on the plumb. In this case, you will see the overall picture in advance, and the curvature of the corners will not be so noticeable against the background of perfectly vertical canvases. If you do markup and glue wallpaper on a fliesline basis, then there is absolutely no matter where you start - from the window or from the middle of the wall.
The first rule of the perfect blowing in the corners is not a glue into an angle whole cloth.In most cases, this is fraught with inconsistency with the following canvas and forming folds. If you have chosen a dear finish type, for example, vinyl wallpaper type silk screen with a complex pattern, then it is best to align the angles with the help of plaster or putty, depending on what kind of irregularity is about.
If deviations are not so noticeable, then it is possible to hide small irregularities with the help of an allen. To begin with one of the walls, which rests into an angle, glue the canvas so that it goes to the adjacent plane with a maximum of 4 cm. Consider, the angle should be very thoroughly wedged with glue so that the canvas had a maximum clutch with the surface. With a spatula or stupid side, a knife is prettier to press the leaf in the corner - act neatly so as not to break the canvas. Then, using a rubber roller or sponge, get rid of air bubbles.
The next responsible stage is the sticking of the canvas on the adjacent wall. To begin, again, measure the measurements - it is necessary to ensure that the edge of the new canvase closest to the corner jumped into the already glued 2-3 cm, while the far from the corner the edge went back with the new one.
Then, using a plumb, we determine the vertical line, which passes in the place of the allen on top of the bottom. Gently celebrate it with a pencil and with the help of a ruler and a sharp knife cut through two layers of wallpaper at the same time. Excess the upper cloves themselves will disappear, but remove the remains of the lower web, slightly bent the top layer. Re-wake the bent edge with the glue and it should be pressed against the wall. If you are all done correctly, the result will please you.
With the help of the allen, the problem with pasting external corners. Only the process looks somewhat different. The first cloth is pasted in such a way that one edge wrapped around the corner for several centimeters. In the level of alignment it is likely that there will have to make several cuts, in order to avoid the occurrence of folds. As you followed, the material is made to the base with a sponge or spatula and allow the glue to the glue slightly. Then cut the strip, bent over the corner in such a way that only the thin edge remains, not more than 1 cm.
Before starting to stick the second web, make measurements with a plumb to determine the far from the corner of the edge. Focusing on it, we stick the second cloth in such a way that there is no more than 5 mm in the near corner of the corner. Thus, you will get an inconspicuous junction of cloths.
Now more and more popularity is acquired by flieslinic wallpaper or based on it, and it is not at all surprising. They are distinguished by durability, ease of care, sound insulation qualities. In addition, recently manufacturers produce wallpaper two times wider than a regular roll, 1 meter width and several centimeters. Thus, it is possible to glue several times faster, and the junctions are less.
But many are afraid to acquire fliesline wallpapers, because they are worried that they will not be able to glim them correctly, especially in the corners. Such unrest are absolutely groundless, because it is enough to know simple rules to know simple and beautifully. Let's figure it out in this topic.
In fact, it is the wallpapers that are made of foamed vinyl, and the basis is Flizelin. This lining material based on cellulose fibers, which should be at least 70% of the composition. The main advantage is visually align all the irregularities of the wall, making it perfectly smooth. Also, vinyl wallpapers on a flieslinic basis isolate a room from outside sounds: the knocks and screams of neighbors behind the wall will be less noticeable.
Flizelin wallpaper or vinyl on a fliesline-based wallpaper can be painted several times and even washing a sponge from pollution. And when you decide to make repairs and handle the wallpaper, only the top layer is removed, and the phlizelin will serve as the basis to punish new ones.
Flizelin wallpapers are very practical to glue their adhesive skills. But there are several tips that will undoubtedly use the owners who decided to make the repair with their own hands.
How to glue phlizelin wallpapers can be clearly viewed on the video:
Remember, the main rule of the blowing angles is not to do it with one web, so that one part of the one-piece strip was on one wall, and the second one. In this case, the flieslinic wallpaper can pull, and the result is definitely not falling. This rule concerns both internal and external corners. The right solution will be saved every wall by a separate piece, which simply go through with each other.
To glue competently, there are several ways that will undoubtedly lead you to the expected result.
Option 1. One of the most simple methods is to stick wallpapers in the corner of the bill. Thus, one sheet is glued with a concession by 1-1.5 cm, and the second exactly along the corner line, i.e. The slot is not formed between the wallpaper, and the angle is obtained neat and visually smooth.
Attention! Flizelin wallpaper is quite dense and thick, so the cut will still be visible.
Option 2. This method is most often used in rooms, where the walls are not entirely right, and are a little littered. The first leaf passes with the allowance to the adjacent wall, so as to overlap the entire angle. The width of the science depends on how uneven walls in the room. The second glue the same with the science, so that observing the drawing does not distort and do not shift it. After that, the level or any other level item sell a clear line, and make an accurate incision to the sharp stationery knife. Then it is easy to remove the top extension strip.
The lower part will be harder, but simply move the glued upper, and you will succeed. After that, wrap the edges of the glue again and attach them gently in place. The whole procedure should be carried out as quickly as possible, and then you will get the perfect corner even on such uneven walls.
Option 3. One band is pasted on a wall with a nasky for about 2 cm. Next with the help of a plastic spatula, carefully rushes into the corner. All folds and irregularities are simply eliminated: it is necessary to make several cuts and the backrest, thus removing the irregularities of the canvas and the wall.
Next, we take a long metallic trowel, tightly press it to the corner and neatly one movement cut off the excess remnants of the material. The second strip is glued in the same way and cut. If everything is done correctly and neatly, then you will receive a monolithic seam that will be almost invisible to an outsider.
Some options can be visible here:
In addition to the inner corners, there are also external in any room. Often it is the slopes of windows or niches and protrusions that cannot be left unattended. They have their own fabric features. Via small secrets Glowing will be lightweight, and the corners will be neat and beautiful. Algorithm of pasting of external corners is such:
Some more advice and interesting solutionsTo competently glue the wallpaper, including fliselin-based, on uneven walls, can be viewed on the video:
As a result, I would like to say that flizelin wallpaper and on a flieslinic basis - quite dense and practical materialwhich is very easy to glue. It is perfectly cleaned, and will please the Owners' eye for a long time.
As a rule, one of the most difficult tasks cosmetic repair - Wall pasting with wallpaper in hard to reach places (on external and internal corners, places of pipe passing, etc.). However, if you use special techniques and suitable materials, the question is how to remove. Consider several ways to glue the wallpaper in the corners. Let's start with a simple task - consider the technique of sailing with oven corners. And then study various options Work with uneven joints.
Happy owners of high quality overhaul, as a rule, do not have problems with skews on the walls. Pasting with wallpaper of a flat joint is much easier and does not require extra cost.
Internal and external (protruding) wall interfaces are embarrassed equally. Consider the phased all the work process.
First of all, it is necessary to decide where to start. If thin paper stripes are used, which will be overlapped with each other (usually up to 0.5 mm), then start the window (so that the seams are not noticeable). If the wallpaper is more dense, they will glue online. In the second case, start from the door.
Determined with the direction - you can proceed to measurements. It should be noted how much wallpaper bands to the nearest angle goes on the wall. The fact is that the final band should evenly lie down on the adjacent wall for about 2-5 cm. Excessively cut it better.
Using a plumb or laser level You should schedule a direct perpendicular ceiling line, from it and start glued. So as it moves to the corner, the trellis will not shift (lean).
Now you need to attach the following canvas, but start next to the angle (no matter how even it seemed to) undesirable. For the same reason, leave the back of the adjacent wall in several centimeters. Otherwise, the likelihood of spank and an inesthetical species is high, which will be difficult to correct.
Smoothing the glued cloth in the wall pairing places are very carefully. Not so bad if the edge of the strip that goes beyond the angle will perform somewhere for 3 cm, and somewhere on all 5. It is much more important that in the junction of two walls wallpaper firmly seamlessly to the surface without chances, fiscased and excess tension.
Tip! If during the repair to be lazy to tightly press wallpaper in the corners, then later the pleasant deployment of holes in saving wallpapers will be a very exciting occupation for the child.
The next strip of light paper or thin wallpapers on the flieslinic basis can be glued on top of the back of the previous one, focusing on the direct perpendicular line, as close as possible to the joint of two walls. Before you start new wall, It is possible to crop over, if the edge of the dress is uneven, or leave the bottom layer as it is.
Wallpapers, glue jack (that is, dense, not stretching after blasting with glue) in the corner are processed by the following technology:
As in the case of paper wallpaper, There is already a small width of the strip, which remains after sticking the grinders on the adjacent wall. We will apply glue on it, press and thoroughly decloid the whole angle.
On top of this strip - the caution - montirhae, focusing on the perpendicular line, a new wide strip. It remains to make a smooth junction (after all, the material is dense, perhaps the embossed, the nest is impossible to leave).
According to the perpendicular line with the help of a building rule or a sufficiently long line, it is necessary to make a deep section of wallpapers from the ceiling to the floor. It must go through both layers by making a smooth edge on each side. It is most convenient to do it a very sharp stationery or construction knife (the second is preferable, since its blade is not bent so much).
Now you need to carefully remove all the extra trimming, smoke the edges of the oncoming stripes and reap the joint. It should turn out perfectly smooth, at a distance of 1-2 cm from the corner.
Tip! You should not do the nest or the wallpaper butt directly in the corner. There are always holes or cracks that will spoil a smooth edge. 1-2 cm from the angle is the optimal distance, both for the inner pairing of walls and for external.
Most often, both in old houses and in new buildings, there are walls with a slope. The meeting place of two such plates can surprise with their shape. Unless on the spiral not wrapped, and everything else is the usual thing. In practice, 2 were developed effective method Work with uneven angles.
The first is to preliminarily prepare walls by alignment (more expensive, but more qualitative), the second - does not require extra costs, it allows you to stick the wallpaper "as is", while it does not hide the relief flaws. Let's start with the first.
If the room has a rectangular shape, the place of pairing two walls should have 90 degrees. If this angle changes somewhere, it means that the wall curves came into the joint. Check it easy. It is enough to apply the coal and spend from the floor to the ceiling, estimating places where the line does not touch the surface. If you fill these "voids", then the output will be perfectly smooth for pasting form.
It will take a spatula in the form of a corner (90 degrees), putty (than a variety of relief by the walls, the more), construction rights andlo, plumb or level. In the most protruding place of the angle, it is necessary to attach a spatula, mark its location. On this line, perpendicular to the ceiling to fasten on the wall construction Rule (Dowels or Samores). Maminating the water surface, apply putty, and, pressing the rule to the edge, spend several times with a spatula. Smooth bog ready. Everything that remains is to remove excess putty, dry and handle sandpaper.
Tip! If you do not have a suitable spatula on your hand, you can use a smooth and dense rectangle from the tree.
It will take a plastering corner (it is a grid with an at-iron or plastic rail, bent at an angle of 90 degrees), putty or plaster. All you need is, this is perpendicular to put a plaster corner, evaluate the gaps. After moisturizing the surface, apply the construction mixture, attach a profile, to dissolve the putty so to hide the grid. Having dried and finishing with emery paper, you can already bold corners with wallpapers. By the way, a similar method will help protect the joints from destruction.
Align the walls (respectively and angles) sheets of drywall. This is the most expensive and efficient method. If the walls do not have significant deformations, then plasterboard sheets can be simply glued, aligning in terms of level. This is one of the most simple waysharder - install sheets on metal carcass. This method allows not only to level the walls, but also to improve thermal insulation indicators, however reduces the area of \u200b\u200bthe room.
With the help of non-good rules, you can save the joints with the joints between the walls and without prior alignment.
Consider some of them:
Not be sure to be wizard all hands to get perfect option home interior. It is enough to follow these simple rules, since exactly the circumscribed angles of the room: without the offset of the general drawing, without bloating and distortion, is an indicator quality repairs.
