Speaking about how to glue vinyl wallpapersIt is important to note that their sticking is performed only to join, because the material is distinguished by a high-definite structure and relief. When applied with adhesive composition, it is necessary to carefully treat the edges of the clouds, so that after sticking they do not spit out and did not dissolve.
Before glue vinyl wallpaper, you need to decide on the choice of glue. We need specialized glue, which is designed to stick such a canvase. For example, if you use the usual wallpaper glue, then during sticking of the canvas will be stretched, and after drying, they will simply be squeezed, as a result of which there will be ugly joints between them.
For such a type of wallpaper, special glue is for sale, high-qualityly holding vinyl bands, which does not allow them to shrink, not allowing the dimensions after drying.
Important! We need to be treated with glue and wall wallpaper (although it is often limited to the application of the canvas). You can not stick the canvas if glue is processed only by the wall. If the surface is primed with glue, it is not necessary to process it - it is enough to apply glue to the vinyl web.
The stores sell canvas of different typesBut all of them are implemented under the general name "vinyl".
The most popular species are:
Important! For each variety of vinyl wallpaper, its type of glue is provided. For example, if the cloths are made on the basis of foamed vinyl, it will be necessary to buy an expensive glue composition, which will be able to keep heavy finishing materials on the wall.
To perform work, you will need to use the following tools:
Important! In order for the vinyl canvas to stop and do not turn off after sticking, the rough surface must be prepared to prepare for the salary process.
The process of preparing walls to pasting vinyl wallpaper - long and time-consuming, which includes consistent steps, each of which is required to be executed:
2. Alignment of the surface. After removing the old coating, it is necessary to visually inspect the work surface. It must be smooth, without defects, crumbling concrete, etc. You can climb the wall with a rubber hammer to check its integrity. Small defects can be sealing with plaster, but if the entire surface is in an unsatisfactory condition, then the old plaster must be eliminated to fully and handle the wall with a new composition to align it.
Important! It is ultimately not recommended to stick the vinyl wallpaper on the former wallpaper coatings or paint, even if they are in satisfactory condition. The optimal option is to remove the old coating and paste the new web to the pure aligned black surface.
It is also necessary to check not only the evenness of the draft surface, but also its humidity. It is not recommended to glue vinyl wallpapers on those surfaces that are constantly exposed to moisture and wet (especially relevant for old wooden and other country houses).
If the wall is constantly wetting and becomes at least a bit wet, then any varieties of vinyl canvas will not hold on it.
Before glue vinyl wallpaper on a prepared wall, it is necessary to take into account tips on the implementation of this process.
They will be useful to those who have to do this work for the first time:
Important! No need to stick wallpaper if there is an increased humidity in the room.
On video: Tricks sticking vinyl wallpaper.
Marking of walls under the sticking of vinyl wallpaper is one of the most important work stages.
If it is ignored, then when sticking, the vinyl canvases will start gradually shifted, they will have to constantly mix them and move, which will lead to additional time costs and increased consumption of material.
Standard residential rooms have 4 walls and 4 corners. Clear vinyl wallpaper can be started from the wall with the window or from the angle that is located closest to the window. If sticking is supposed to be done from the angle, then it is necessary to immediately measure the verticality of this angle. It is necessary that the first strip of vinyl wallpaper "lay down" is perfectly smooth.
To do this, from the angle of the room in the direction of the adhesive, it is necessary to retreat about 3-4 cm. Then you need to take a plumb with a colored cord, fasten it in the top of the wall. If there is a partner, then the lace can hold it from above. The plumb must lower down, conducting a strict vertical line. Then the lace must be pulled out and release, due to which a smooth vertical line will remain on the working surface. In the future, it will be possible to poison subsequent vinyl wallpapers.
The second side of the first wobbly strip will be driven into an angle with a slight occasion on the adjacent wall. In case the angle of the room does not have the perfect vertical, due to this navigation, this drawback will be almost completely leveled.
The process of sticking vinyl canvas also includes several stages that must be executed sequentially. Camping is a simple process that can be performed together.
The main thing is to purchase high-quality and suitable glue composition, as well as follow the main recommendations.
The glue for vinyl wallpaper needs some time so that the mixture is blown, therefore kneading the adhesive composition - the first stage. It is necessary to prepare the adhesive mixture strictly according to the instructions on the package (it will be unique in each case depending on the manufacturer).
Glue for vinyl canvas is usually required to fall asleep into a container with a predetermined amount of water. Flipping of dry adhesive powder is gradually carried out with constant stirring of the resulting mixture.
Vinyl wallpaper can be with a clear pattern, which will require high-quality fit, or without it. In the first case, consumption of canvas will increase significantly.
Waste will be absent if you need to glue vinyl photo wallpaper.
If the cloth with a pattern, then it is possible to customize it in several ways:
Important! If there is an opportunity and there are vinyl wallpaper with a margin, it is recommended to choose the consumable first method, because it is easier to perform and weaken.
The retention roll, you need to take into account the height of the surface of the surface, the displacement step and make the stock of the length under the final trimming. There is enough stock in 5-7 cm. In the marked place, the wallpaper must be passed, to smooth out, cut off with scissors or a sharp knife.
Casting walls with vinyl wallpaper is performed sequentially. There is a specific scheme, in accordance with which such work is carried out.
Glue vinyl wallpaper better together.
Work is carried out in the following sequence:
2. The band of vinyl wallpaper is needed from above, applying the top edge of the canvas to the pre-glued etern with a small adhesive. IN vertical plane It is strongly recommended to align the glued strip using a level.
3. After gluing the upper part of the band, it is necessary to gradually, moving to the bottom, press it to the wall with a plastic spatula or roller. Praise the band is best using the Herringbone method, i.e. Removing the air moving the spatula from the center to the edges of the strip. The glue from the vinyl web is recommended to immediately remove the clean cloth or sponge.
4. Sticking the second strip is performed in exactly as well, but now you need to glue it so that the drawing has matched. First, it is necessary to align the canvas strictly through the joint line, after which it is already engaged in combining the pattern.
5. For the angular parts of the room, it is necessary to use bands that should enter the adjacent wall by about 3-4 cm.
After the vinyl wallpapers are pissed, it is recommended to carry out all the remaining building materials, tools, tank with adhesive composition out of the room.
The door and windows in the room are worth closingto speed up dryingdo not include a fan or air conditioner.
After sticking, you need to wait at least 1-2 days so that the adhesive mixture is frozen. If immediately after sticking, open the window and create in the drafts of drafts, then the likelihood is that the vinyl wallpaper is simply dug.
The finishing of the walls by ordinary paper, even if it is very strong, today is not in fashion, it is much more interesting, finding out how to stick the vinyl wallpaper correctly, decorate the room by creating your unique design.
If you decide to abandon stereotypes in the decoration of the residential rooms, to start a more widely look at the available materials. Paper today looks almost primitive, but in the opposite extremes throw not worth it - and the plug is quite expensive. Fliselin is quite available at cost, but requires very careful circulation and, without having experience, it is better not to get involved with it. It remains to find out how to point the vinyl wallpaper correctly, perhaps it will be the most optimal solution and price, and on the simplicity of finishing.
So, the choice is made. Now let's look at the most careful material to which preference was given. In fact, it is the finest layer of PVC, or, in other words, polyvinyl chloride, rather common flexible plastic. The most common types of wallpaper from it are smooth and foamed. The first are divided into compact vinyl and silkographic (with the addition of silk yarns). The second, obtained by heat treatment, is divided into such varieties as severe, high density and chemical embossed.
The advantage of vinyl is that it can be washed, and special impregnations exclude the occurrence of fungi. In addition, the foamed or textural surface of the material allows you to hide small irregularities on the wall or ceiling. The lack of such wallpapers is that they do not miss the air completely. In other words, if the house is built from "breathable" materials, the vinyl finish will turn the placement in the thermos. In the process of sticking, the paper base can be stretched, which is why the material is impaired with the material.
Masters of the site site prepared a special calculator for you. You can easily calculate the required number of wallpaper.
The first and basic rule that need to be adhered to when finishing the room - in no case is not a glue wallpaper from vinyl on uneven walls, only small sherbins can be exception. Yes, the material under review is able to smooth out the minor curvature of the plane of the walls, but here the keyword is "minor". And the protrusions are not even most unreasonable. Therefore, as carefully as possible, with the help of plaster and putty. If you have to finish on the material with a high degree of moisture absorption, it is pre-handled by primer. Only then glue the vinyl wallpaper with their own hands.
In the room, the walls of which will be covered with wallpaper, should not be cold and damp, in addition, you need to turn off the air conditioner and take care of the absence of drafts.
The glue can be welded yourself, it can be a hub or any other option available to you with the addition of PVA. However, the homemade composition is far from always good, especially if you need to cover them the wall. The fact is that on a dark concrete or at the primed cement plaster will be badly visible, where the glue is already applied, and where it is not yet. And the unreasonable plots will definitely turn into problems when covering wallpaper walls. Therefore, it is better to take special mixtures that, thanks to certain additives, being applied to any plane, paint it into light pink color, becoming transparent after drying.
Before proceeding with work, take a plumb and pencil, and check how vertical the line of the angle, from which the walls are best started. The angle is choosing arbitrary, it is desirable that closer to the door, if it is not vertical, we apply a plumb to the upper point and fed a molded line. Next, we will describe in detail the technology of sticking vinyl wallpaper.
On well wash and dried floor unwind the roll face down. We take a roulette and measure the necessary length, after finding out the height of the wall from the ceiling to the plinth (taking into account the ceiling curb). We make a pencil mark on both edges of the roll and connect their cut sliced \u200b\u200bline, according to which we separate the measured piece of the panels. Similarly, we divide the remaining roll on the equal parts, combining with the previous canvas so that the drawing match on the joints.
Previously, the battered vertical line, from which we need to glue the wallpaper can easily be fastened when applying glue, so we carry out a pencil on it. Next, we have 2 ways. If the vinyl layer is applied to a paper base, with a roller cover with glue wallpaper strip, after which we fold its ends to the middle and leave swell on exactly the measured time, usually specified on the roll.
During these few minutes, it is possible to have time to progress the wall with adhesive mass. If the basis of the phlizelin, glue is mostly applied with a roller on the wall, and the cloth cover them only around the perimeter.
The most difficult stage begins - sticking vinyl wallpaper with your own hands. We take the first strip for the upper corners (if they are with a paper base, it is very neat, not stretching) and apply a line marked earlier. You can glue from the ceiling, and with a small indent, observing it throughout the perimeter of the room. Special skills require the insertion of a piece of wallpaper in a gypsum baguette.
Close down the cloth from top to bottom, sequential movements pressing it to the wall. It is best to do this with a wide foam roller, only be sure to take clean, do not confuse with those with the glue.
Before glue joints of vinyl wallpaper, we apply stripes to the wall, observing the drawing. Remember, the material with which you are working, sufficiently tight and braziness always looks extremely ugly. In places of outlet of the walls of the wires (switches, sockets), we make small holes before the cloth will completely close this section, and we derive the wiring to the outer side of the cut.
Then continue to smooth out. If the ceiling has a bias, for example, in the attic room, we apply a lane to the previous one, keeping the next cut for the corner nearest to the seam, and the second leave hang out freely. Then, pressing the cloth on the top edge of the wall, cut off the extra piece with an acute stationery knife.
In the process of smoothing, watch the air remained under the wallpaper, it is also necessary to try not to stretch the canvas, because the folds will appear. The overaction of glue is also diligently driven to the edges and then remove a clean cloth. If the air bubbles were still formed, carefully singe them with a needle and press the wallpaper canvas in this place, smoothing the roller. When we get to the corner, we try so that the strip moves to the next wall with the edge is not wider than 5 centimeters, especially if the angles are uneven. At the end of the work, it is neatly cutting up not yet sucked canvas on a plinth and make wider holes in places location of switches and sockets. Wallpaper without air conditioning and draft, without opening the windows and tightly cover the door.
Many people are interested in how to glue vinyl wallpaper. We will fulfill this wish, but at first we will help to figure out why these wallpapers became extremely popular and which constitute these finishing materials.
The vinyl wallpapers are taken from the middle of the last century, the creator of which were two American engineers, one of which opened the excellent properties of polyvinyl chloride, and the other put this material on the paper basis. Unfortunately, only in our time, people appreciated this unique material, which rightly became the leader of sales and all sorts of ratings. Therefore, the intersener's interest in vinyl wallpaper is quite natural, which is seen from numerous requests on the Internet. Subject " How to stick the vinyl wallpaper?"Constantly on hearing.
Today, manufacturers have been established by the release of two types of vinyl wallpapers, which are bred by their shareholder, in one case it can be paper, in another - fliseline. However, this is not the only difference, today in the market building materials There are on sale wallpaper of this category, part of which are foamed polyvinyl, thanks to which the magnificent structure of the material has been created.
It has an unusually dense, non-standard heterogeneity of the invoice, so that the wall surface can not be made to the perfect degree of evenly, which is a prerequisite for wallpaper of other categories. Small flaws and defects material will hide, while its surface will look impeccably smooth.
And, of course, the characteristics of vinyl wallpaper deserve attention - they are practically impeccable and comply with the requirements of our time.
Buying this material, you should pay attention to the icons applied by the manufacturer on the packaging of each roll.
First - This is a way of applying glue. The indicator is very significant, it should be strictly followed when sticking vinyl wallpaper. Because manufacturers are offered varieties, prescribing in one case to apply glue on the wall, in another directly on the back side of the wallpaper. These are completely two different production process. And now add another option to them, in which the wallpaper is supplied with a glue layer applied to them in the factory conditions.
Secondly, Spend some time to study the characteristics of wallpapers, which are divided depending on their confrontation efficiency by exposure to moisture and dampness:
The beginning of the walls of the walls with wallpaper is preceded by removal from the surface of the former finishing materials (of course, if the apartment is not from the new building). It is possible to remove old wallpaper quite easily, it is enough to moisten them with water (preferably warm) by means of a sponge or painting roller, wait a while so that they are well soaked in moisture, and then, using a spatula, separate from the wall.
In the case when the wall has been performed on the wall water-emulsion paint, There should be a drill with a metal nozzle in the form of a brush. And so regardless of the former finishing material, Old coating is subject to mandatory removal. Perform yourself this work is quite able to any inhabitant, the main thing is to be desire.
Then it is necessary to carefully examine the surface to identify and remove the identified defects and flaws. Cracks, recesses, chips and other little things can be sealed with a putty or plastering solution. The freshly abandoned leveling material must be given time for drying, after which the surface should be primed by a primer mixture deep penetration, dry and re-apply an aligning finishing layer of putty.
But since now we are talking about the pasting of walls by vinyl wallpaper, it is quite enough will be the first layer of putty, which, together with the removal of defects, will simultaneously be the leveling layer, which will remain to bring to the relative evenness of fine-grained emery paper and primer (and also give the primer time to dry). And if they will remain some roughness, the bulk material itself will absorb.
We draw your attention to the fact that when choosing a primer should be caution, because in the building materials market a huge set of these products. And you should choose special glue for vinyl wallpaper. But if it so happened that for some reason it is currently no, you can use wallpaper glue, which should be dissolved with water to liquid state. Such a mixture is also very good for the primer of the walls under the sticking of vinyl wallpaper.
Having finished with all the preparatory work on the wall with a plumb, it is necessary to apply a vertical line, it will become a reference line defining the correctness of the sticking of the wallpaper in a strictly vertical direction. It is very easy to perform this process - tighten the screws on one of the walls under the ceiling, to which led the thread of the plumb. The plumb itself will pull the thread, you will remain with the help of a pencil and a long line to spend a parallel line on the wall, which will become the starting line to accommodate the first wallpapers.
Once again we remind you that vinyl wallpapers have a high density that allows you to effectively cover small defects and flaws on the wall surface. Therefore, stopping your choice on vinyl wallpaper, when implementing preparatory work You can not spend time on the finishing equalizing putty layer, which contributes to saving labor costs and finance.
The wallpaper of this type is made quite large width, which helps to reduce the joints. More correctly and rationally, if you prepare wallpapers before starting the wallpaper sticking, the bands must be cut into so much so that they are enough for pasting all the walls of the room (for counting the needs of the bands, it is necessary to perform simple arithmetic actions). The length of the strip must be equal to the height of the surface of the plus of five to ten centimeters of admission to various unforeseen circumstances.
Then the glue mixture is going on, it is applied in accordance with the icon on the roll, that is, either on the wall or on the back side of the wallpaper. The glue is better to apply a painted roller, which will evenly distribute glue over the surface, while it is better to wash the surface with glue only under one bar, and after sticking it, move to the treatment of the next sequence of the wall.
After that, the top and bottom of the band are reduced together (the back of the inside), lift to the ceiling and, holding the top of the wallpaper strip, dissolve it to the bottom, watching it to lay exactly along the drawn line you have applied before. Further, we recall the strip with a rubber roller or a plastic spatula, at the same time squeezing air residues under the material. For a dense fit of the material to the surface, the leveling should be carried out from top to bottom and simultaneously from the center of the wallpaper strip to its edges. The subsequent entertainment of the blended wallpaper depends on the thoroughness of the execution of this process.
Vinyl wallpaper glued is much easier than paper, because unlike its analogues, the vinyl bands are stacked. Although some masters use the technology of their brazing stickers, however, they do this at the expense of small tricks - impose the following lane on the previous one with a nasky of about two or three centimeters. After mounting the second cloth, make a vertical section in the middle located one to another bands. Then the upper cut strip is removed, and the bottom, which is located under the second strip, should also be removed. After that, the edge of the second strip must be applied. It turns out a smooth junction, almost imperceptible to the eye. This technique speeds up the process of pasting and reduces the possibility of gaps between strips.
We told a variant in which the wall surface was glared, and if the wall strips are missing with glue, then the prepared wallpaper should be placed on the floor and melt the rear-side of the material with adhesive mixture. It is also better to make a roller, thanks to which you can achieve uniformity of the adhesive layer. Wallpaper should be applied to the surface of the wall 5-6 minutes after blasting with glue - this time is enough so that the material is well soaked. The further global process is performed by the same technology as when applying glue to the wall surface.
In case you smear the glue to the wallpaper strip, observe moderation, because quite a small layer of the mixture, the main thing is that the material was missed by glue carefully and evenly.
Also, after the location of the wallpaper on the wall, avoid stretching the material to the sides. And no less substantially - timely remove the remnants of glue, do not allow it to dry. It is better to make a clean soft cloth.
So, we figured out how to qualitatively caught the wall surfaces with vinyl wallpaper and it becomes clear that it is practically much different from sticking any other types of wallpaper. At least one to one to the main stages. Therefore, the manual, who at least once had to glue the wallpaper, can also perform the process of stickers of vinyl wallpaper, and moreover high level, not inferior to the work of a highly qualified wizard.
The main thing is not to hurry and follow the wisdom of the life advice - it is better to measure seven times than to cut off once.
Once time for any family comes overhaul One, several rooms or the whole apartment. Let's talk in detail about the technology of gluing vinyl wallpapers on the walls of the rooms. Will be voiced practical advicethat will help you yourself or with an assistant to make repairs.
Before dealing with optimal option gluing wallpaper, consider their views. There are two main varieties of materials:
Both varieties - bilateral. One side is a paper or fliseline, the material is glued to the wall. The second is polyvinyl chloride, thanks to her room after repair it will look elegant. These materials have been known for a long time, from the 50s of the twentieth century. Poklasika produced by special technologyUsing special adhesive mixtures.
For productive work, you need to prepare all the necessary tools in advance.
Before sticking, carefully prepare the work surface (wall). We are preparing as if they wanted to glue ordinary materials.
Important!
Do not use the putty, which has the basis of PVA glue. Vinyl wallpaper will not be transferred.
The second nuance - manufacturers are recommended to pasting the wall additionally gently and thoroughly primed. It concerns heavy, thick wallpaper. To stick the lungs, you need to remove all cracks from the walls, align the bulges, other irregularities. To do this, put a puttyle to the prepared surface in compliance with all technologies. It is impossible to allow it immediately after drying or after some time behind.
The technology is such that they first cut them into the required size of the strip. Pasting along the entire length of 10 cm on both sides. If you purchased the canvas with a pattern, then try to pick up the second neighboring band so that both are most docked.
Before chopping, be sure to look at each roll series. If it coincides, perfectly, you can begin training. Having found a roll with a different series, open it and see one shade of the canvas? If yes, you can use it in the design of the surface, if not, then set aside. It can come in handy in many years, if the pet hurts the plot, the spare wallpaper can be pushed a damaged piece of coating.
You need to glue the vinyl wallpaper. With this method there is a nuance: when our wallpapers are dried, they can suddenly "rush", noticeable gaps will appear in the form of tracks. Therefore, the material having a vinyl base, the adhesive is inflicted slightly less than on paper.
Do not pull them width when you stick. Cress the material to the wall of a special comfortable roller with a rubber surface or a brush, which has a short pile. Spatula Do not use. Pressed? Carefully, gently draw the tool on the seams.
Wallpaper with vinyl coating It is necessary to glue exactly just
Since these wallpapers when sticking the capricious, they are, like others, are glued with closed windows and windows to accidentally not create drafts. The material does not endure when the air temperature is sharply reduced or the humidity changes or changes. Therefore, remember that the ventilation will have to postpone and do not even turn on the air conditioner.
Look carefully that the adhesive mass accidentally did not hit facial Our canvas, otherwise it ruins him. Especially if you do not notice and remove it in time.
Water glue for vinyl wallpaper with water. How? This is written in detail on any package. Wait until the mass is sweeping, according to the instructions, it is about 5 to 10 minutes.
There are two main ways of applying adhesive composition:
What option is needed in your case? Read carefully on the roll packaging. If it is easier to say, if the basis on paper, on the wallpaper we apply the composition (you can on the wall, including), and if on the fliesline - only on the wall.
We try to glue the vinyl wallpaper correctly. They are not immediately pressed against the wall after applying adhesive composition. First, the wallpaper gently fold so that the base is to the base, and expect the glue to impregnate the canvas. Thinner material will be ready faster, and before with a dense will have to wait a little longer.
If you want the material on the wall carefully - glue is uniformly throughout the canvase and a rather thick layer, but at the same time, observing the measure. If everything is done correctly, the seams after pasting should remain as clean as possible.
How to glue the corners with vinyl wallpaper? Incorrectly combining the canvas in the corner - exactly where the walls of the walls. It is necessary to fly from 2 to 3 cm for one of the walls in the direction of work.
In the corners, the stripes need to glue slightly brass
Conveniently glue vinyl material with helper. One person climbs on the stepladder with the web upstairs and presses the wallpaper to the surface of the wall. The second remains downstairs and supports the lower part. At the same time, he thoroughly aligns the entire strip strictly vertically. To make it easier, many are careful in advance and spend a vertical line.
After alignment, the wallpaper is easily pressed, displacing the air bubbles formed between the wallpaper and the wall. To do this, use a brush - so faster and more qualitative than hands. The brush is carried out from top to bottom, then from the center spend to the edges. If you notice at the edges of the excess glue, immediately wipe the clean towel, fabric cloth, cloth. The main thing is to do it carefully, carefully that the composition does not accidentally hit the front part.
The extraordinary edges remaining after sticking under the ceiling and in the plinths we cut using a sharp knife. If the tool is stupid, do not be lazy - wear, otherwise, the blade doubts and unevenly breaks the edges. Under the edge of the plinth takes only 0.5 cm of material. It is best to remove the plinth, and then kill.
As for switches with sockets, make them up to work and remove them. Wallpapers are glued straight on the holes, and when they dry, they are cut through the contour of the nests and set there old or new sockets, switches.
After pasting, excess paper over the sockets are cut off
No matter how hard you try, and the last strip will be less standard size Rulon. Experienced people try to make these sites fall on the window opening or turned out above the door. But newbies may not work. How to be?
The output is simple. If a canvas range from 5 to 7 cm widely unclosed section, then on one side we can glue it, with another brand to the adjacent strip. Moreover, we try to make it so that the "unnecessary" part of the band is not glued, but remained slightly bent. As always, carefully drive out from under the canvas air with glue. Now we take a very sharp knife for the stationery and cut off an excess piece for the line. Do not press much, you can accidentally cut through the putty, and our task is only to remove an extra piece. Now, as always, we look at the edges tightly coincided.
From all written above, you can make several conclusions. Glue vinyl wallpaper is not scary and not difficult. The main thing is attentiveness, accuracy, properly prepared wall and competently selected glue.
Any dwelling from time to time required redecorating, and sticking wallpaper is the most important part of it. The modern market offers a large assortment of materials for every taste and wallet. For example, very popular vinyl wallpapers on a paper basis. They are quite inexpensive, but at the same time high-quality, reliable and very simple in care. But can we glue them correctly so that they will serve us as long as possible?
A huge range of colors, drawings and textures will help you create unusual design interior with vinyl wallpaper
The peculiarity of vinyl wallpapers on a paper basis is that their lower layer is made of paper. This determines the low cost of the product. For example, wallpaper with a phlizelin basis will cost more, although the upper layer consists of the same polyvinyl chloride.
In the production of vinyl wallpapers on a paper basis on a substrate by spraying or creating a film, vinyl is applied. His, in turn, foam or embossed.
It is this material, polyvinyl chloride, makes vinyl wallpapers with such universal.It is very resistant to pollution and mechanical effects, and its elasticity allows you to recreate a variety of textures and drawings. You can not only wash such wallpaper, but even paint them, which will greatly simplify repair work and expenses on them.
But not everything is so perfect, unfortunately. For example, a paper foundation has some drawbacks compared to fliselin:
As far as these shortcomings are tangible, every buyer is wave to solve himself. Most often, low price is a decisive factor, especially since its backgrounds are not very noticeable. This is evidenced by a great demand for vinyl wallpapers with a paper basis.
Choosing the wallpaper of this type, pay attention to their classification. According to the structure of the surface, they are separated into smooth and embossed, and according to the finishing method, they can be embossed or profile. Thus, vinyl wallpapers are divided into several types.
Example of vinyl wallpaper with silk screen
Wallpaper of paper-based compact vinyl
Wallpapers from heavy vinyl with thick top layer
Example of vinyl wallpaper with chemical embossed
In the process of sticking wallpaper, you may encounter certain difficulties. Invite someone from friends to help you: work will go faster, lighter and more fun.
The following tools will be required to work:
In addition, you need wallpapers themselves and glue. To his choice, come thoroughly: it is strictly not welcomed by the use of flieslinic glue for wallpaper with paper substrate. It is better to use glue with marking wagon, vinyl or express.
Choose a special glue for your type of wallpaper and use the instructions on the package.
Make sure that there are antifungal supplements in the glue. If your wallpaper is very heavy, it is better to choose special glue.
Some use PVA for sticking vinyl wallpaper. Yes, it is very firmly holding a coating, but it will later be difficult to remove it from the wall.
Before glued wallpaper, you need to make sure that the surface is dry. Check it easy: stick to the wall a small segment of a polyethylene film and leave until morning. If overnight on the film donkey condensate, the wall is still insufficient enough. You can also stick the usual tape, dramatically remove it and look at the sticky side. Properly prepared and dried wall will not leave its pieces on the glue layer.
Do not forget that when sticking wallpaper, even vinyl, the room should be warm, dry and windless. No drafts, included air conditioners and fans! Otherwise, the result of your work will be the surface in bubbles with which with time the wallpaper will start to spin.
The subtleties have a lot of subtleties. You will have to face joints, sticking in the corners, and the ceiling finishes will require certain efforts. But you will probably handle all these troubles.
Do not try to cut holes in the wallpaper wallpapers in those places where switches and sockets will be - they may not coincide. It is better to do it when the wallpaper will be crooked and light up slightly.
Cut the roll of wallpaper on the canvas required length, wake them with glue and let it be soaked
Another feature of the vinyl wallpaper is that when they are blending, you can not apply glue on the wall, it is enough to treat the cloth.
Leave sheets in this position for a few minutes.
It is at this stage that you will need an assistant. It is much more convenient if one person cuts out and, and the second on the stepladder sticks the canvas on the wall.
Carefully press wallpaper to the wall with a roller, excess glue clean the pure cloth
If you did not remove the plinths before work, be careful with the surplus of the wallpaper
Do not forget that the vinyl wallpaper on a paper-based after sticking should dry at least 2 days. All this time in the room must be supported optimal temperature (from 15 to 20 degrees Celsius) and absent drafts. Violation of these conditions can lead to the appearance of bubbles on the surface of the wallpaper.
You may encounter some difficulties when sticking vinyl wallpapers in the corners. There are two common ways to cope with this problem:
To stick the vinyl wallpaper on the ceiling, you will surely need an assistant
Vinyl wallpapers on paper basis is a great idea for pasting the ceiling: thanks to its ease, they are well held on the surface.
The process of sticking wallpaper on the ceiling is practically no different from the similar finish of the walls.Is that hands get tired much more, and you will have to do frequent breaks . Nevertheless, it is necessary to repel the starting line along the wall so that later to align the first wallpaper canvas.
If you first walked with vinyl wallpaper walls, and then started the ceiling, it is very important not to blur with glue already finished work. For this wall, the walls can be sealed from the top or fasten with painting tape flashes on them. After the end of work, you will easily remove this defense without leaving any traces.
