House, design, repair, decor. Yard and garden. Do it yourself

Evgeny Sedov

When the arms grow out of the right place, live more fun :)

2 mar. 2016

Content

Often wallpaper materials are the most familiar wall decoration. Their popularity has increased due to affordable price and ease of pasta, but not in all places. FROM smooth surfaces Any can cope, but in the question, how to glue the wallpaper properly in the corners, not everyone can prove himself as a professional. In order not to brake the repair process and make it better, you will have to resort to some construction tricks.

Features of shook wallpapers in the corners of the room

The salary of the straight surface of the wall is not difficult, but it is only worth reaching turning - the hassle starts. How to properly glue the wallpaper in the corners? Already experienced in this business, people recommend novice to observe several conditions:

1. Do not use the whole cloth on turn. Whatever even it seems to be - still turning out folds and skews, because some modern wallpaper materials give shrinkage after drying.
2. Do not start to bold from the very joint walls - it is not so smooth, as at first glance. It turns out that two panels are spoiled at once. Instead, you need to take the level and draw a vertical line.

There are 2 ways to glue the wallpaper in the corner:

1. To impose a web on top of each other and make a cut in the center of the adhesive. Cut parts remove.
2. Print one cloth, heading the edge of 1.5-2 cm per turn, then jack it - a prepared second piece of material.

Preparation of walls

Before starting, you need to produce preparatory work:

1. Inspect the shelves of the walls for the presence of irregularities. They need to be aligned with a putty, which will dry a couple of hours. After that, clean the surface with emery paper to achieve perfect smoothness.
2. Using the level of chalk, draw a straight vertical line by retreating from the joint of the walls by 4-5 cm. There will be the edge of the canvas.

Step-by-step technique

To start salable, you need to prepare necessary materials - All of them should be at your hand. The wallpaper sticker in the corners requires the following:

• wallpaper canvas of the desired length with a margin in a pair of cm;
• diluted in warm water glue, suitable according to the characteristics to your material;
• roller and brushes for applying glue;
• dry rag for erasing excess adhesive composition;
• brush for cracking closure;
• line;
• construction knife;
• stool to get to the top of the canvas.

How to glue internal angles

Here are the stages of work, how to glue paper wallpaper In the corners:

1. Applying glue. Thoroughly wake the prepared composition of the joint of the wall of the walls on top of the bottom, because the material is spacing easier and more often. Use where the roller will turn out, and where you need to have a brush.
2. First part. On the side where the material has already pasted, glue the following part so that it falls around the rotation of about 4-5 cm, as shown in the photo. Press the edge of the sponge. Strongly push the turn to the place to carefully fix it.
3. The second part of. Start another wall. Knowing the width of your material, measure it on the wall so that one edge of the panels came to the previously glued to 2-4 cm. Swipe, checking it on vertically. Apply the glue on the wall, glue the second canvas. Click edges with a sponge.
4. Trimming too much. Arm yourself with a ruler and a construction knife. In the center of the allen, make a vertical incision using a ruler. Gently tear off the walls of the top cloth and remove the bottom cropped part.
5. Final gluing. The part that was turned holes thoroughly wake the adhesive composition and re-glue to the wall, smoothing the edge and removing the excess glue. Perfect seam is ready!

How to salary external angles

The protruding parts are more noticeable indoors, so they must be performed particularly carefully. There are two options, how to swing the wallpaper:

1. The protrusion is perfectly smooth. Then just wrap the cloth behind the angular junction by 3-4 cm and glue. Do not cut it off, and the next glit according to the usual technology for the direct surface.
2. The walls are uneven. We will have to use another way.

The second method will not differ from technology for internal angular joints. Here's how to glue wallpaper in protruding corners:

1. The first strip is covered with an adhesive for an angular junction of about 4-5 cm.
2. Measure the width of the cloth and retreat another 5 mm so that when sticking, one part has driven slightly to another.
3. By line, make a cut in the middle of the adhesion.
4. The upper part will disappear, and the bottom remove, moving away the top cloth and sticking it into place.

Such methods are assumed to those materials that stick to the joint and do not give shrinking strains. So the seam will not disappear and there will be no lumen in the wall. For paper materials, these methods are not suitable - a 0.5 cm pad is required, so the first method is used when the nest is not cut off, but simply check for vertically with a plumb. If deviations detected, they carry out the line and cut unnecessary. For more aesthetic design, a corner for wallpaper is often used.

Planned or redecorating The apartment is unlikely to cost without such a labor-intensive process as design walls by wallpaper. However, today for decoration of walls is often used phlizelin wallpapers, having some benefits in front of their paper analogues.

For example, such wallpaper options are allowed to be subjected to wet cleaning, they remarkably hide the shortcomings of uneven walls and save their attractive design for a long time. In addition, phlizelin wallpaper is enough just to fix on the wall, because it is quite convenient in work. finishing materialwhich does not forms vertical, horizontal folds and bubbles. Traditional sophisticated outer and internal corners can be issued by phliselin material, without experiencing serious difficulties. For this, just need to take into account some nuances.

The easiest way to get a beautiful lawn in front of the house

You, of course, saw the perfect lawn in the cinema, on the Alley, and perhaps on the neighboring lawn. Those who at least once tried to grow a green platform in their own area, without doubt they will say that this is a huge work. Lawn requires careful landing, care, fertilizer, watering. However, only inexperienced gardeners think so, professionals have long known about the innovative agent - liquid lawn Aquagrazz.

For finishing the corners of the room, do not attempt to use a solid piece of wallpaper in order to arrange both closed in the corner of the wall. In this case, the wallpaper will "behave" with almost a guarantee, and the formed folds will have to be cut, which will adversely affect appearance walls. However, even if it is possible to avoid, a curve angle (unfortunately, this standard practice for domestic builders) can affect the further design of the apartment with wallpaper. After all, phlizelin wallpapers are applied on the walls of the "joint in the joint", respectively, the skew allowed during the passage of the angle will force the entire remaining web blades.

Fliseline Room Corners Finish

The correct blowing of wallpapers in the corners with wallpaper from nonwoven cellulose material is as follows:

If everything was done without errors, the junction between the stripes of fliesline wallpaper will be difficult, it will need to be treated with a roller or rag.

Outdoor

Features of pasting with wallpapers of external corners indoors

External angles in the rooms are much less common internal, but come across. The technology of applying flieslinic wallpaper in this case is almost identical to the passage of internal angles.

At the first stage, we are engaged in geometric surveys:

1. We measure the distance - from the edge of the last paste strip to the outer angle - and we prepare the next wallpaper band so that it is after fixing it on the wall "wrapped" with an angle of no more than 50 millimeters.
2. We determine the point of the wrapped strip close to the corner, it is from her that we will start glue a new wallpaper band.

Accordingly, measures are carried out to apply vertical strip and removing wallpaper residues.

By the way, if outdoor Smooth, as evidenced by not only a visual inspection, but also checking with the help of a construction plumb, it is allowed to use one wallpaper band. However, it should be borne in mind that possible discrepancies should not exceed 5 millimeters.

Paper wallpaper

Wallpaper is still popular with finishing works Inside the apartment. This is due to their very democratic price and the sticker way. It is worth noting that the paper wallpaper is not able to hide the serious defects of the surfaces of the walls and corners. The method of fixing paper wallpaper on the walls is not too different from similar technology with wallpaper from Flizelin.

The easiest option implies the sticker of this finishing material "Vakhlest". In other words, the wallpaper cloth is glued in the corner with a small intake (1-1.5 centimeters) on the adjacent wall, and the next strip passes directly in the corner itself. It distinguishes this method of efficiency, but here the visual effect leaves much to be desired.

Paper Wallpaper - Application Features

The second way to beat the wallpaper in the corners is suitable even for some "diluted" walls forming angle. The initial stage fully corresponds to the previous method, the only difference - the inlet on the adjacent surface is made somewhat larger. The next lane of wallpaper is also glued "Vangest", but its long-round side must be oriented along the vertical strip applied with a plumb. The canvas should lie down with overlapping in 2 centimeters, while having a common border with the adjacent wall. Then according to the applied vertical lines. special knife Both layers of finishing material cut forward, and after removing its residues, you can begin to further design the apartment walls. Do not forget to handle the cutting line with a special roller.

As you can see, the method of sticking in the corners of paper wallpapers is very similar to the method of fixing phlizelin wallpaper.

Finishing of external corners with paper wallpaper

External angles are found in the form of window slopes, decorative partitions from plasterboard, etc. In any case, the geometry of such an angle is extremely important, because such an angle, unlike internal, is constantly in sight. Therefore, possible defects of an external angle should be eliminated in advance and only after that begin to sticker wallpaper.

Wallpaper sticking technology in corners

The technology of sticking wallpaper on the outer corner is very similar to the second method of fixing the wallpaper on the inner corner. However, the "nestling" on the adjacent wall should not exceed 5 centimeters, this is due to the fact that a large ink in the uneven wall surface will be difficult to align. Depending on the quality of the wall and wallpaper, the appearance of folds is possible, they are eliminated by special horizontal cuts on the canvas. The next lane of wallpaper is glued close to the corner, but its far edge should pass along a predetermined vertical strip. Next with a painting spatula, building level Or the metal line we press the center of the launch and the wallpaper knife cut both web. After the remnants of wallpapers are removed, they need to be put down and handled the roller. The docking compound in this case will be shifted by several millimeters from the corner itself, but it should be so. Otherwise, there is a risk of tearing wallpaper as a result of a careless movement.

Small tricks when working with wallpaper

The key value when working with internal and external angles has a finishing material:

• It is not necessary to apply glue in advance to the paper, it is very high that they are soaked through them through and break in your hands. However, this type of wallpaper does not require trimming when the angles are passed. Due to the fact that the wallpaper is very thin, the docking connections are enough to try dry with a dry cloth or roller.
• Vinyl wallpaper, on the contrary, is better to treat glue in advance and give them to absorb it. Wallpaper from vinyl is quite tight material, and with in advance prepared The canvas will be easier to work.
• It is not necessary to apply glue on the fliesline wallpaper, it is applied only on the wall.
• The general rule for all types of wallpaper is what they must be glued in the premises where there are no drafts, air conditioners and heaters do not work.

Do not forget that the walls in front of the wallpaper sticker must be necessarily processed by primer. In addition, the glue must correspond to the type of such a finishing material as a wallpaper. Firms specializing in production different species Wallpaper, indicate the accompanying documents the most suitable adhesive mixtures for their products.

Required tools and materials

Tools and materials for pasting Wallpaper Apartments

In order for the design of the apartment with wallpaper, it is quickly and successfully, it is advisable to take care of the presence of the following tools and materials:

• dry rag or sponge to eliminate glue excess;
• construction hairdryer;
• brush;
• a vacuum cleaner;
• stewbridge or scaffolding.

RESULTS

Wallpaper, despite all their shortcomings, as the type of finishing materials used for interior decoration Apartments are among the most popular, this is due not only to their price, but also by the fact that they can be pasted without the help of third-party specialists.

Most of our fellow citizens are confident that possessing even a little experience repair work, It is possible to stick wallpaper efficiently and beautifully.

Perhaps this is how it is when it comes to smooth walls and straight corners.

But few of the apartments, especially it concerns unsuitable Khrushchev, can boast of indicators.

How to stick the wallpaper in the corners? Where to start it, from which side?

Next, choose anglefrom which we will start work. Preparing a piece of wallpaper desired size, smear it with glue, if necessary, they are covered and a piece of the wall for which it is intended. When using plastic corners, they also wake up the composition. Folding the wall, you can go out a few centimeters beyond the future sheet.

Adhesive first lane. If the work is carried out from left to right, then in the corner is applied left-hand side Wallpaper stripes. In all its length, it must be placed perfectly smoothly. Clean fabric or special device (plastic spatula or roller) The coating is smoothed over the entire area, moving gently and gradually, kicking out the air and removes bubbles. The wall to the nearest angle is completely covered.

How to glue wallpaper in inner corners

There are precisely angles of this type. For competent and smooth salary, you need to adhere to the listed recommendations.

The strip is glued so as to cover together with an angle and several centimeters of the adjacent wall (3-4). It is carefully pressed and smoothed by a clean cloth without a pile.

Then, on the adjacent wall using a ruler from the top angle, the width of the canvas is postponed with a minus mentioned 3-4 cm. This is done in order to stick the next strip relative to the previous bill.

Through a plumb or level along the whole wall, a line is held, which will serve as a reference. It should be strictly vertically, the band should be glued.

After that, you can move to the adjacent wall. As already mentioned, the next strip is glued on the walls of the Vangest line the previous line. Just like everyone else, it is carefully smoothed and pressed, especially in the place of the wall of the walls. Then, using a sharp knife, a ruler and, both layers of wallpaper rubber on the corner, unnecessary trimming are removed.

It is necessary to do it carefully to accidentally do not remove the desired piece of wallpaper. Then the edges of the canvas are waving glue, smoothing and pressing. Follow the air bubbles not formed. If you use this technique for finishing the angles, you can make an angular joint with almost imperceptible visually.

How to glue wallpaper on the outer corners

Meanwhile, along with internal, external angles are found in each residential building. This, for example, all familiar slopes.

To make them easier and carefully, it is advisable first. Unfortunately, it is not possible in each case. Then it will have to apply a method of misunderstanding.

How is it more convenient to do this?

As when working with inner angles, the layer of material with an adjacent wall is glued, at the distance of the previously mentioned 3-4 centimeters.

To ensure an even fit of wallpaper to surfaces, in several places it is allowed to gently cut them. When the canvas smoothed, the blade or sharp knife along the vertical face is cut off, except for the fine edge.

Then a large ruler or construction tape measure on the wall, the distance equal to the roll width plus five millimeters is measured. With the help of a plumbing from this point, we carry out the vertical line.

The next wallpaper band will stick, focusing on it. When gluing two adjacent bands will be minor toast, which disguises all possible defects formed when trimming the first piece.

How to glue in the corners with a picture

If we have to work with a coating that have a clear and intelligible drawing, it is important to ensure that the wallpaper sticker in the corners does not distort the existing pattern. Make it is not as hard as it may seem.

The main thing is not to forget about the need for some allen. In addition, glued the canvas in such a way that the edge will definitely match the plumb. Then, on the verge of an angle (edge), the second edge is cut.

Prevent the pattern shift is completely quite difficult, and small distortion can take place. But it will be so insignificant that it is most likely to know about him, you will most likely. Only a careful study of the intersection lines and compounds to notice it. If you fulfill all the recommendations on pasting inner and outer angles, individual material canvases will be shaken vertically, and the small distortion of the picture will not be noticeable.

Conclusion

For the salary of wallpapers in the corners there are small secrets.

Even if the joints are not too smooth, however, they will look neat and beautiful.

The main thing is to be patient and careful, to do all the events leisurely and carefully. Then the result will please you!

Like it, we can glue wallpaper. The point is quite simple. It is almost like glue children's stencils - except, by the way, such types of wallpaper, the adhesive layer for which has already been applied.

That's just the material much more and glue does not need a bottle, but a bucket. Therefore, we proceed to the case quite tearing, choosing the beginning of the treated surface.

Basic provisions

Corners - far from the most prominent place of the interior of any room, but it is the quality of their finishing and determines this class of work.

Here we will only define, to begin with, with what situations we can encounter.

Types of corners

The order of work will largely depend on what kind of angle will take us:

• internal between two vertical walls - there are such in any room, there are almost always no less than four;
• outdoor, also between the two walls - there may be no such thing, they can be avoided by separating the slopes of windows to the angle; But if there is an external angle, it will require the most of all work;
• inner horizontal downstairs, between the floor and the wall;
• the inner horizontal above, between the wall and the ceiling - the last two types could not be taken into account if you prudently approach the organization of these corners.

About materials and tools

Before you begin work, consider with what we will deal with:

• Fliseline wallpaper - they are the main cause of all our actions, the most famous finishing material for the walls. Wallpapers are performed on the basis of long-standing paper - in them 70% occupies a cellulosic layer, but with the addition of strengthening and give more flexibility of the synthetic component that ensure the wonderful qualities of this material. To work at the corners here, good flexibility, and from additives - high strength that will not give the material to break at the most inopportune moment.
  When it comes to wallpaper, their dimensions are especially important:

• in width, you need to count on 53 or 106 cm,
• and in length (height) - by 10.05 meters.

• Glue - you can use universal glue For wallpaper, but we recommend nevertheless special precisely for phlizelinov, which, by the way, is not suitable for any other.
• Rollers - it is advisable to stock whole set for all occasions:
  • for applying glue;
  • to smooth wallpaper, already on the working surface;
  • to work at the joints, and
  • to work at the corners.

• Reference, line, level, pencil, scissors - measure and cut a lot, but most importantly - from the very beginning it will be necessary to get an ideal vertical line on the wall, all further work will begin.

Helpful advice!
If you are able to strictly adhere to the obtained vertical in the future, it will be enough and one.
But we advise on all four walls, closer to each corner, carry out these lines that will allow you to control the process more accurately.
Vertical departure always leads to very unpleasant errors and even the need for complete rollover.

• The cutting tool is necessarily comfortable with a well-honed edge;
• Stretch, Kelma, a comfortable wide range - whatever, which will allow to get and control the cut line.

Nuances of preliminary training

The stage is preceded by very important actions to prepare the draft work surface.

As for the corners, it will be very important:

• when working at the top and bottom - to provide installation of plinths at the last line, after wallpaper, then:

• the task of fitting the junction simply disappears by itself, the edges will be closed by plinths, providing an ideal joint;
• in this situation, if you consider the standard height of the premises 2.5 meters, the length of the wallpaper is 10, and the height of the plinth along the wall is 5 cm, then the roll is cut into 4 pieces of 2.5, which are enough for four verticals, and without any waste ; Otherwise, given the allowances, it will have to cut more than 2.5, which means that 3 pieces will go to the case and one shortened will remain to the village or to the city;

• it is very useful to use removable plinths - so solving the problem with the docking, if in the future wallpaper will want to change;
• when working on inner corners - they need to strengthen the phlizelin paper ribbonwhich is glued directly to the putty, and on top of it also put off;
• on external corners - it is better to carry out more capital strengthening with metal or plastic corners, which are fixed with screws; Corners are attached to the shplotovka, and on top are also put off.

Helpful advice!
If you have no corners, we advise you to use plastic cornersThey are more convenient to select the necessary angle.
The variants of the strengthening corners are quite a lot, but, given that, on the corners, we will slightly cut the wallpaper slightly, it is better to use solid corners, without perforation.

• if we talk about the surface as a whole, then it should be:

• carefully sucked
• leveled
• protubed,
• saxplanovan I.
• coloring - at least emery manually, but better by machine.

Stroke work

Consider in order all the angles, from simple to complex.

Corners at the top and bottom

Everything is quite simple here, even if you do not manage to hide the material under the plinth:

• we cut the wallpaper with a switch above (or below) the plinth by 6-8 cm;
• we glue and bend the allowance of the plinth linewhat is convenient to do;
• then, using a spatula as a guide support, cut the battery with a knife along the entire length.;

• work must be performed while the glue has not grabbedThis will allow a small residue in 1-2 mm gently with a knife for the plinth line.

Angle

Here, first we ensure yourself with two reliable verticals on both jammed surfaces:

• first we glue the wallpaper on one side in such a way that the plot, width, not less than 2 cm, passed to the adjacent wall;
• we wait for the glue completely dry;
• usually it will be enough for the attachment of a neighboring piece.If you have done more, and it keeps well, then cut it no need, otherwise, be sure to cut, using a sharp knife and a spatula as a guide;
• we glue a piece on the next wall in bulk to the corner and smoke it special;

• there is always a temptation to avoid such a wrist, bend a piece in half the width and try to create an "ideal" angle from one piece; But, as practice shows, the wallpaper will start running in the future and the whole corner will simply move away; Nevertheless, we advise this way to keep in my head; If you have very high-quality, "non-running" over time, and even under glue wallpaper, then this option will be just perfect.

Helpful advice!
When sticking the wallpapers, in no case stretch them onto the glue - when the glue dries, the material will definitely "frighten", exposing wide joints.
In addition, be sure to determine what type of wallpaper at your disposal.
There are options that generally should not be glued, only jack.
Some glue only with a shift relative to a neighboring piece or even with a rotation of 180 degrees.

The article can find the answer to the question how to glue the wallpaper in the corners. It is worth considering the process of finishing with full responsibility, irregularities can rush into the eyes, thereby spoil the impression from freshly repairs.

Step-by-step instruction of sticking inner angles

When finished, the main problem can be uneven walls and resulting from this fold on the wallpaper. It should also be borne in mind that with curved walls of the jokes of woeful canvases can diverge.

How to glue an outer angle (outdoor)?

The protruding angle must be pasted by analogy with the internal, but there are small differences that you also need to take into account when working.

What if the corners are uneven?

Uneven walls Frequent problem of old houses. Before you start glue finish coatingIt is advisable to prepare preparatory work and bring the surface "in order". If visual angles are smooth and do not require overhaul, It will be enough to walk with a hard tissue, removing small irregularities and dust. If irregularity is noticeable with a naked eye, then it is better to carry out a little work before starting glue wallpaper.

Features of adhesive meter wallpaper

Wide canvas are convenient because allowing the finish with a smaller number of seams on the surface. It is more difficult to glue them, but the result is worth it.

How to dock in the corners?

It would seem that such a trifle how to glue the corners in the room can completely spoil all the work during incorrect execution. And if on the wallpaper also the drawing that needs to be customized is worth it to approach the finishing.

How to customize drawing in corners?

It is important that the drawing is continuous and smooth throughout the perimeter of the room. To do this, you need to combine the pattern, and crop excess.

1. The bands are also glued to the mustache. Leaves allowance on both walls.
2. Plastic spatula wallpaper pressed against the corner.
3. After sticking the second web, the wallpaper is trimmed by drawing. This method refers to wallpaper with a small pattern. For a large pattern, under the edges may be required.

Before glued, you must first prepare the material for work, spreading the coating on the floor and having studied the pattern. Segments are cut off after the selection of the drawing in height.

Features of trimming wallpapers in the corners

In order to get the perfectly smooth seam in the corner you need to correctly cut excessive.

1. After the wallpaper is pasted against the wall, a smooth metal line is applied, it can also be a spatula or rule. In order for the cutting line to be smoothly, you can use the level.
2. Excess the edge of the line is cut off with a sharp stationery knife, after which the upper wallpaper layer will go away.
3. Carefully comes up and getting the bottom layer of wallpaper is removed in the same way.
4. The canvas are labeled with glue and tightly pressed to the corner. As a result, the coating is tightly adjacent to each other.

Glue wallpaper in the corners is not so difficult, but special care and accuracy is required. Today there is a way of finishing, which allows you to perform work at all without jams, namely liquid wallpaper. They are applied with a smooth layer and do not require such difficulties as fitting patterns, widths, accuracy in rounded places and other nuances.