Due to the simplicity of installation, operation and safety of gas speakers Junkers They gain their popularity both in private homes and in ordinary high-rise buildings. This device will be very useful in families with young children, because because of the frequent shutdowns of hot water supply, the child may get sick, and constant heating of water on gas stove not very comfortable.
All German gas columns Junkers are equipped with various species Flatbed. This serves as the basis for distinguishing them from each other. Gas speakers are available in the following versions:
The first type of columns does not have a burning stamp, so the ignition in it occurs with two batteries.
If you look at the feedback from this version of the column, we can conclude that its service life is more than 10 years, which is a big plus in comparison with the analogues.
Junkers p is equipped with a piezorozhig, that is, the stammer that is installed in the device will be in the adjacent state constantly when the device works. It is not automated, so you have to independently adjust the water pressure in the system.
The form G is equipped with a hydrodynamic generator, which produces a pathele of the burner (there is no scatter in it). Such a device is capable of working at a pressure of 0.35 atm and is equipped with Hydro Power technology. Also this type of the column of Junkers produced in two sizes:
All components they have the same, the difference lies only in size.
The apparatus has both advantages and disadvantages. Advanced benefits the following characteristics:
Thanks to its design, Junkers will perfectly fit into any interior. The device operates at a gas pressure of 13 mbar. Such pressure is present in all gas pipelines in Russian houses. If you compare it with European pressure (20 mbar), it is significantly lower, which creates problems when buying other gas columns. The device effectively functions in multi-storey housewhere pressure in watering system Very low (running from 0.1 atm.)
Junkers has increased safety and low cost in comparison with its analogues. When changing the water pressure, the device will automatically select the power at which the water heating will be optimal. The device is collected by German designers and has a guarantee of 2 years. For proper installation and operation The device will be able to serve over 13 years.
Among the disadvantages are allocated The fact that in most modifications of gas columns Junkers has an increased level of noise. During the operation of the device, problems with heat exchanger and leakage in seals appear, which creates a risk to spoil flooring Under the gas column or at all are flooding neighbors.
Often the device breaks due to its improper operation. It happens that this is due to corrosion, poor water quality and jumps electric voltage. If a marriage was found after the acquisition, it is eliminated for free in the service center.
Paid repair approximately cost 1500 p. The price depends on the complexity of the breakdown. It is recommended to independently turn the device to the service in order to save on delivery or call a private wizard. The most frequent faults are:
Basically, these breakdowns occur due to the formation of a large layer of scale. In order to repair the device yourself, you need to determine the cause, purchase original spare parts, follow the recommendations of specialists and explore the basic rules for the repair of this type of boilers.
After repair, it is necessary to make sure that all the fixtures of the device are correctly fixed, and during its operation there will be no leakage of gas. Independently repairing the device is allowed only if there is similar experience. Only original spare parts purchased from Bosch should be applied.
The cost of the device depends entirely on the size (standard or mini) and its version (B, P, G). On average, the price of type B varies from 10 to 13 thousand rubles, on the view P from 6.8 to 9.7 thousand rubles, on the version G from 11 to 12 thousand rubles.
Each device is completed detailed instructionswhich describes the technical component of the device, installation, installation, configuration and care instructions. The manufacturer recommends not to install the device independently, but to confes the specialists from the gas service. After all, the wrong installation can not only break the device, but also to cause significant harm to the ineptly installer.
The device has a large number of positive feedback from satisfied buyers. They consider it a reliable, safe and affordable apparatus.
Junkers existed before 1932. From this point on, the company was redeemed by Bosch Gruppe, which, however, did not affect the name of the water heaters produced by the unit.
Outflow gas columns Junkers (Junkers) are available in several modifications, differing in the ignition principle, as well as the type of combustion chamber. The domestic consumer is popular with flowing boilers working using opt burler. The average service life of the UNCERS column exceeds 15 years.
In the internal device of gas flowing columns, the Junkers uses exceptionally high-quality materials. All water heaters undergo mandatory testing and are subject to certification.
More information O. specifications Speakers of the Junckers can be found from the following table:
Specifications | Model column junkers |
|||||
Power and water flow |
||||||
Max. Nominal thermal power PN (kW) | ||||||
Min. Nominal thermal power PMIN (kW) | ||||||
Heavy Power (adjustment range) (kW) | ||||||
Permissible pressure of the supplied gas |
||||||
Natural gas H G20 (MBAR) | ||||||
Liquefied gas (butane / propane) G30 / G31 (MBAR) | ||||||
Gas consumption |
||||||
Natural gas H G20 (m³ / h) | ||||||
Liquefied gas (butane / propane) G30 / G31 (kg / h) | ||||||
Number of nozzles | ||||||
Hot water |
||||||
Max. Permissible PW (bar) | ||||||
Water volume switch in extreme right position |
||||||
Increase temperature (° C) | ||||||
Duch range (l / min) | ||||||
Min. PWMIN operating pressure (bar) | ||||||
Water volume switch in the extreme left position |
||||||
Increase temperature (° C) | ||||||
Duch range (l / min) | ||||||
Characteristics flue gases |
||||||
Necessary thrust (mbar) | ||||||
Waters of flue gas flow (g / s) | ||||||
Temperature (° C) | ||||||
In the labeling of the water heater, detailed information regarding the principle of operation and internal device. Disassembled in abbreviations will help table with decoding designations:
Gas pressure adjustment table |
||||
 | Natural gas H. | Bhutan / Propane |
||
Number Identifier | for reconfiguration at 20 mbar | |||
for reconfiguration at 20 mbar | ||||
for reconfiguration at 20 mbar | ||||
Connection pressure (MBAR) | ||||
Max. Pressure until the nozzle (mbar) | ||||
Min. Pressure until the nozzle (mbar) | ||||
After connection flowing water heater The passport is put mark on commissioning. From this point on, the Junkers column is plans for warranty service.
To clean the junkers column at home, you will need to do the following:
Repair of gas columns Junkers with their own hands leads to the manufacturer's refusal of the manufacturer's warranty service.
The description of the breakdown and the methods for eliminating the Junkers gas columns are provided in the table:
Fault | Elimination |
|
| The ignition burner is blocked. | Clear. * |
| Gas is fed in insufficient quantity. |
|
The water temperature is too low. | Check the position of the power regulator and set at a higher power. |
|
The burner is turned off during the operation of the device. |
|
|
Reduced duct water. |
|
|
* can only make a service and repair master |
||
Gas speakers Designed to heal water in apartments and houses that do not have central hot water supply. The devices are easy to use, safe, allow you to adjust the degree of heating.
All Junkers water heaters are adapted to operate in Russia and have a number of advantages:
The columns in the method of ignition are divided into three types:
Series in - constantly burning stamp is not available. Rijigue comes from two batteries. Turning on the column automatic, there are several security systems: control of thrust, fuse, ionization adjustment of the flame. The flow of water and the temperature are adjustable depending on the water pressure in the water supply. There is a fault indicator. Junkers series in Made from high quality copper and will serve at least 15 years. Models: WR 13 B, WR 15 B, WR 10 B (minmaxx).
Series P - Piezorozhig. The spinner burns constantly. Power and water flow are adjusted separately. Control flame thermoelectric. Models: WR 13 P, WR 15 P, WR 10 P (Minimaxx)
Series G - Hydropower ignition technology. Minimal water pressure 0.35 atm. There is no burning stamp, the ignition is carried out from the hydrodynamic generator. Gas water heater Series G provides hot water At the same time, 1-3 watershed points. Models: WR 13 G, WR 15 G, WR 10 G (Minimaxx).
All models are available in two sizes: standard and mini. Equipment of both versions is the same, the difference is only in dimensions. The price depends on the size of the apparatus and the need for delivery and installation. The average cost in Moscow is reflected in the table.
|
The lineup |
Price, ruble |
||||
|
standard |
Height, mm. |
Width, mm. |
Depth, mm. |
||
| WR 350-3 KDP. | WR 13p | 8 200 | |||
| WR 350-3 KDB. | WR 13B. | 10 700 | |||
| WR 350-3 KDG. | WR 13 G. | 11 400 | |||
| WR 400-7 KDP. | WR 15p. | 9 600 | |||
| WR 400-7 KDB. | WR 15B. | 12 000 | |||
| WR 275-1 KDP. | WR 10P. | 6 700 | |||
| WR 275-1 KDB. | WR 10B. | 10 100 | |||
| WR 275-1 KDG. | WR 10G. | 10 600 | |||
If buying a new model does not afford, you can find a good used device. He is an order of magnitude cheaper.
Possible breakdowns
Junkers appliances design is one of the most perfect today. But breakdowns still happen due to improper operation, voltage drops, scale formation, corrosion of the case. Factory marriage in all service centers is eliminated for free. On average in Moscow, the cost of repairing a gas column Junkers 2 000 rubles. If you call the wizard to the house - it will be more expensive if there is a technique in the service yourself, then cheaper.
Characteristic faults:
1. Goes off the wick ignition. The cause can be a breakage of thermocouples, valve or chimney gas sensor;
2. It does not heat water. The reason is a breakdown of the heat exchanger;
3. The water heater is noise and overheats. The reason is a radiator breakdown or a score scale;
4. The housing is leaking. Problems with gland or heat exchanger;
5. Gas the spark of ignition. The reason is broken the flame controller;
6. Spontaneous shutdown.
Is it possible to repair yourself? Sure! For this you need:
Therefore, the elimination of any malfunction of the gas column should be carried out by a specialist with special skills and knowledge in this area. Repairs must comply with GOST and standards for this type of work. Only in this case can be calculated on long-term and reliable operation, eliminating the risk of explosion and gas leakage. Original parts can be purchased at BOSH dealerships. Thus, the new hydroarmatura will cost approximately 7,000 rubles, the stall is 500 rubles, and the electronic ignition unit is 5,000 rubles.
The apparatus has both advantages and disadvantages. Advanced benefits the following characteristics:
Thanks to its design, Junkers will perfectly fit into any interior. The device operates at a gas pressure of 13 mbar. Such pressure is present in all gas pipelines in Russian houses. If you compare it with European pressure (20 mbar), it is significantly lower, which creates problems when buying other gas columns. The device effectively functions in a multi-storey house, where the pressure in the plumbing system is very low (running from 0.1 atm.)
Junkers has increased safety and low cost in comparison with its analogues. When changing the water pressure, the device will automatically select the power at which the water heating will be optimal. The device is collected by German designers and has a guarantee of 2 years. With proper installation and operation, the device will be able to serve over 13 years.
Among the disadvantages are allocated The fact that in most modifications of gas columns Junkers has an increased level of noise. During the operation of the device, problems with heat exchanger and leakage in seals appear, which creates the risk to spoil the floor covering under the gas column or at all are flooding neighbors.
Specifications | Model column junkers |
|||||
Power and water flow |
||||||
Max. Nominal thermal power PN (kW) | ||||||
Min. Nominal thermal power PMIN (kW) | ||||||
Heavy Power (adjustment range) (kW) | ||||||
Permissible pressure of the supplied gas |
||||||
Natural gas H G20 (MBAR) | ||||||
Liquefied gas (butane / propane) G30 / G31 (MBAR) | ||||||
Gas consumption |
||||||
Natural gas H G20 (m³ / h) | ||||||
Liquefied gas (butane / propane) G30 / G31 (kg / h) | ||||||
Number of nozzles | ||||||
Hot water |
||||||
Max. Permissible PW (bar) | ||||||
Water volume switch in extreme right position |
||||||
Increase temperature (° C) | ||||||
Duch range (l / min) | ||||||
Min. PWMIN operating pressure (bar) | ||||||
Water volume switch in the extreme left position |
||||||
Increase temperature (° C) | ||||||
Duch range (l / min) | ||||||
Characteristics of flue gases |
||||||
Necessary thrust (mbar) | ||||||
Waters of flue gas flow (g / s) | ||||||
Temperature (° C) |
Of course, the operation of any technique does not always go smoothly, it is worth being prepared for everything. Fortunately, a significant part of the probable malfunctions arising from the Junkers gas column is easy to solve independently.
The reasons why burner does not ignite, really a lot.
Sometimes the Junkers column does not light up, and sometimes the device is turned off itself.
In addition, the spinner can clog out from the inside, which is easy to fix clean. The abundance of rust, dirt in filters due to waters of poor quality and electrodes leads to similar consequences. Finally, the installation violation, the covered valve on the pipeline pipe and wire problems are also common causes of interruptions in the work.
There are still several common cases. If there is no spark at the instrument with autorun, then maybe there is no ionization current, which means that water does not flow. Iskra goes out when the flame controller broke. If the column does not heat the water, then the reason may be in perforation of the water block membrane, contaminating the tubes or incorrect assembly, but most often - in the heat exchanger breakage.
When the water heater makes too strong sounds and heats up, this suggests that the radiator broke or scored scored.
The leaking case is the consequence of heat exchanger problems or a seal.
About how to light the gas column Junkers, you can learn from the video below.
Often the device breaks due to its improper operation. It happens that this is due to corrosion, poor water quality and electrical voltage jumps. If a marriage was found after the acquisition, it is eliminated for free in the service center.
Paid repair approximately cost 1500 p. The price depends on the complexity of the breakdown. It is recommended to independently turn the device to the service in order to save on delivery or call a private wizard. The most frequent faults are:
Basically, these breakdowns occur due to the formation of a large layer of scale. In order to repair the device yourself, you need to determine the cause, purchase original spare parts, follow the recommendations of specialists and explore the basic rules for the repair of this type of boilers.
After repair, it is necessary to make sure that all the fixtures of the device are correctly fixed, and during its operation there will be no leakage of gas. Independently repairing the device is allowed only if there is similar experience. Only original spare parts purchased from Bosch should be applied.
In the columns with Piezorozhig, the scarlet should be buried constantly, because when the crane of hot water opens, it should break the main burner. The attenuation of the stobnant turns off the gas supply column so that the gas does not accumulate inside the apparatus.
The spinner can go out if:
If the gas column does not turn on at all, read another article.
Samoa frequent cause Atoys of the stobnant call a faulty thermocouple. Its main function is to overlap gas access to the column if the device works unstable. As soon as the spinners, the thermocouple fixes the lack of heat and gives a signal to turning off the gas. However, if the thermocouple itself is damaged, it causes fitheel attenuation.
The situation is no less common when dust or some garbage fall into the nozzle. Their diameter is very small, so even a little contamination may prevent the burning of the stamp, as a result of which the thermocouple is not heated enough.
The fact that problems have appeared with the stall and it can go out at any time, prompts the color of his flame. In a normally working wick, the flame will be blue by 90% and may include some red specks, and its tip can be yellow. If the flame of the ignition burner is predominantly yellow or orange, it means that the phytyl works incorrectly, the thermocouple will be heated enough, with the result that the burner will go out.
About others possible reasons Attening the stobnant, see the next video.
To better deal with the reasons why a gas column can be fused, it is necessary to understand the principle of operation of such a device. Just having studied the essence of the water heating process, similar to the device, you can talk about its faults.
Before starting the operation of the gas column, you need to get acquainted with the instructions
There are a lot of manufacturers producing gas columns. These are also known to the whole world costly bosch and grain, and more budget analogues like columns Oasis, vector, Evva Suite 5514, Beretta, Avangard, Astra, Mora. In any case, the basic principle of operation in all above the presented models is the same. The only one, there are columns automatic and semi-automatic, but the difference between them is insignificant.
Main elements, gas column:
Thus, there is no reservoir for the accumulation of water in the gas columns. Passing through the heat exchanger, the liquid heats up in a matter of seconds, thereby ensuring the constant flow of warm water at once in several water intake points.
Natural gas is used to heat the water with a gas column. Such raw materials are at times cheaper than electricity, and the popularity of gas speakers is impoverished.
Knowing a gas column device, you can understand why it goes out. We describe you the main problems, and tell me what to do in this case.
If you are interested in the gas column "Junkers", then you should consider the features of different models that relate to a specific series. For example, the equipment of the series in does not have a constantly burning stamp. Rosge is carried out from two batteries. The column turns on automatically, possesses several safety and control systems.
You can use the flame ionization adjustment functionality and rely on the operation of the fuse. The temperature and flow of water are regulated depending on how water pressure will be in the water supply. You can learn about the faults by display. The columns of this series are performed from high-quality copper, which can serve for 15 years. The gas column "Junkers" can also be related to the R series, the equipment in this case has a piezozhig, and the stall will burn constantly. Flow and power are adjustable separately. Through the thermoelectric system, the flame intensity is controlled. In the equipment, which relates to the G series, the manufacturer has provided the ignition technology. The most minimal pressure of water at which the column will operate, is an indicator of 0.35 atm. The device does not have a burning stamp, and the ignition is carried out by means of a hydrodynamic generator. If you prefer one of the G series columns, you can expect to connect the equipment immediately to three points of water intake. All models may have a minimum or standard size. Both versions have the same equipment, and the difference lies only in dimensions. The cost depends on the apparatus and the need for transportation and installation.
If the column works badly, it turns off quickly and slowly turns on, then you may have encountered one of the above problems described. In this case, you need to find out the reason, and if it is not very serious, try to eliminate it yourself. Let's talk more about several of the most common problems to cope with whom you can without the help of the master.
If the gas column goeshes, it is impossible to operate it
The most common problems, due to which the wick is not lit in the gas column:
These are the three most common reasons, because of which it may not work as Chinese and the branded column. After conducting simple manipulations, you can cope with a similar problem on your own.
Installation and connection is better to entrust the specialist who has been instructed to work with such a type of equipment. In addition, he will be able to suggest which original parts should be purchased, to diagnose the equipment and prevents any malfunctions. Nevertheless, even a professional must follow the instructions that are sold along with the product itself.
Junkers characteristics suggest that the device is ideally adapted for Russian conditions. It is adapted to pressure, which is supported in Russian gas pipelines, and is equal to 13 millibers. In addition, the system is capable of working with low water pressure, inherent in Russian water pipes. Junkers is enough 0.1 atmospheres to perform provided functions.
Such a gas burner is able to heat from 11 to 16 liters of water per minute, which is considered a very high indicator. In addition, the flame power is automatically changing, depending on the strength and size of the water flow. Constructions are safe and able to serve for decent time. Devices are able to provide quick heating of water and look great, which explains their popularity worldwide.
Strict design, variety of models that differ in productivity, design and ignition system, affordable price And the simplest management belongs to their main advantages.
It should be remembered that some actions can lead to a breakdown of the gas column. Junkers will be broken if there is no influx of fresh air. In addition, breakdowns will occur when using too long hoses leading to a decrease in pressure, simultaneously opening hot and cold cranes. Naturally, the lack of periodic prophylaxis will also lead to negative consequences.
Above it was already indicated how to turn on the Junkers column - it is done using a valve and a piezoelectric element that can burn wick. It is worth the burner, and it will work throughout the day. Moreover, as soon as the hot water crane is open, the boiler will be automatically connected. Change the gas pressure and water pressure will turn out, switching two adjusting handles.
If it is decided to clean the gas equipment, it is done according to a specific algorithm.
If the smell of gas appeared, it is forbidden to use electrical switches and telephone in the zone of finding gas burner
It is important to immediately block the gas crane, open the windows, ventilate the room and call the specialists who carried out the installation of the equipment. To prevent dangerous situations, near Junkers do not store liquids and objects inclined to ignition
When the room temperature drops below zero degrees, the burner is turned off and emptied.If before the winter months this procedure was not carried out, then by connecting the device in the next season, it is necessary to check whether water is heated.
The only right solution will cause a licensed specialist from our service Center For cleaning and adjusting the stobble. Check the functions of the thermocouple and gas control system. Gas smoking can be distributed on the main burner, which will also need to take care of the wizard. Usually, if the wick goes like during operation, the commissioning of the work occurs by fullcleaning the gas column.
The cost of the device depends entirely on the size (standard or mini) and its version (B, P, G). On average, the price of type B varies from 10 to 13 thousand rubles, on the view P from 6.8 to 9.7 thousand rubles, on the version G from 11 to 12 thousand rubles.
Each device is completed with a detailed instruction, which describes the technical component of the device, installation instructions, setting up and care. The manufacturer recommends not to install the device independently, but to confes the specialists from the gas service. After all, the wrong installation can not only break the device, but also to cause significant harm to the ineptly installer.
The device has a large number of positive feedback from satisfied buyers. They consider it a reliable, safe and affordable apparatus.
In addition to the above problems, other problems may arise that adversely affect the operation of the column. You can also cope with them yourself.
So that the gas column is not rotten, there should be no drafts in the room
Other reasons for swelling column:
If the column goes out when the button is released, then the satellite antenna of your neighbors is installed above the chimney. In this case, you need to reduce the flame or turn off the device and contact the gas services.
The typical column consists of a casing that is connected to the chimney through the nozzle, the heat exchanger (the best - copper), the gas burner, the ignition system, the sensors and the mechanism responsible for supplying the gas. The gas column is pretty simple.
Its principle of operation can be considered on the model, which has a piezoejig.
You can set the required water and gas consumption.
If the junkers gas column does not ignite, the reasons for this can be in external factors that are not related to the state of the main equipment.
Fault | Elimination |
|
1) The west flame went out again. 2) The ignition flame lights up only after several attempts. 3) Flashing yellow flame. | The ignition burner is blocked. | Clear. * |
1) The west flame goes out when the hot water crane is opened. 2) The hot water temperature is insufficient, weak flame. | Gas is fed in insufficient quantity. | 1) Check the pressure reducer and replace it if it is not suitable or damaged. 2) Check whether cylinders with gas freeze (butane) during the operation of the device. If the cylinders freeze, put them in a less cold place. |
The water temperature is too low. | Check the position of the power regulator and set at a higher power. |
|
The burner is turned off during the operation of the device. | 1) worked the temperature limiter 2) Traction control device worked | 1) Turn on the device again in 10 minutes. When a malfunction is reappearing, call a specialist. 2) Check the room. Turn on the device after 10 minutes. When a malfunction is reappearing, call a specialist. |
Reduced duct water. | 1) insufficient water pressure. 2) Water taps or mixers are contaminated. 3) Water armature clogged. 4) clogged (covered with a lime bloom) heat exchanger. | 1) Check and fix. * Check and clean. 2) Clear filter. * 3) Clear and, if necessary, remove the lime bloom. * |
* can only make a service and repair master |
The main difference between different models of the gas columns is the way they are ignition, whether it is a product. junkers., Bosch, Neva or Suite. Today it is very rare to find a device that is lit with the help of matches, so this option is not even considered.
The most popular columns today are units with a piezorozhig. They just click on the button located on the device panel. In addition, similar aggregates provide for the possibility of setting the desired temperature of the supplied water.
Speakers with an electric vehicle - the most expensive option that allows you to significantly save gas. Turning on the device occurs in automatic mode of water flow. Acquisition of such products allows you to save on an energy source and get heated water with maximum conveniencethat justifies the high cost of the column.
Modern gas speakers offered by famous trademarks, as a rule, have three-level protection:
Equipment is protected from overheating using a hydraulic safety valve.
The reasons for the fact that the water heating device goes out, there may be the following:
If the quality of the water supplied to the room is unsatisfactory (for example, rigid, with a large number of lime impurities), a metal lattice filter is clogged. To restore the normal functioning of the unit, it is necessary to clean (replace) the mixer filter. Cleaning can be produced by conventional detergents to remove rust and scale
Also, it is important to clear the column itself from spectal formations.
For the membrane examination, the bolts are unscrewed that fasten the front panel of the column.
When examining the membrane draws attention to its form (so that there were no deformations), the presence of any chips. . In case of detection of such defects, it must be replaced
And it is better to choose a silicone membrane, since its surface is more resistant and elastic.
In case of detection of such defects, it must be replaced. And it is better to choose a silicone membrane, since its surface is more resistant and elastic.
In this regard, the service life of this part will be longer.
To install the membrane, it is better to use the services of specialists, which will undoubtedly be safer. In addition, when calling the wizard, you can simultaneously and make overall cleaning of the unit, carry out full diagnostics of the device.
The reasons for the attenuation of the gas column may also be the following:
If you decide to buy such a column, then read the reviews on the useful site "Ozzovik". Everyone described his column and set the estimates. My feedback is old enough. http://otzovik.com/review_1713020.html.
Now I would put the fourth four of this column. I recommend buying. Usually everything is treated without spare parts. From the "minuses" of the column, I will note a large price for spare parts. Fortunately, they break not often.
If anyone is interested, I post here for the Istruction on Bosch and Junkers Gas Speakers
Instructions for gas column /upload/file/quickdir/201104111631310. Instructions for columns Therm. 4000 O Type R.PDF
Instructions for the gas column of junkers /upload/file/quickdir/gazovaya_kolonka_bosch_junkers_wr10_13_15p_1.pdf
Briefly I have everything. To climb into the column yourself, or call me, solve you.
Services and prices https://gazmaster34.ru/ustanovka-gazovyh-kolonok-i-kotlov.html
My contacts
I hope the article was more useful to you.
Two main reasons for the gas column goes out:
Initial actions in cases of termination of the unit:
Important! In case the gas column in the off state exudes the smell of gas, it is important to block all the valves, ventilate the room and call the gas services. .
To clean the device, which supplies gas for burning (nozzle) such actions are carried out:
In addition, the most common cause of the attenuation of the gas column is described in this video:
The range of products produced today in this market segment is incredibly diverse, so the consumer is difficult to navigate without prior preparation and consultation of the professional. Modern gas speakers for water heating are stylish design, as well as a practical and convenient control panel.
The product under the Junkers trademark produced in Germany embodied most of the wishes of the most demanding buyers, which ensured him stable popularity over the years. No less worthy devices are devices produced by brands such as Bosch and Electrolux.
Related records
