Plasterboard cabinets are not so rare, but appearance You can rarely distinguish them from ordinary embedded structures. Such cabinets often replace partitions or interroom wallsWhat makes it possible to use space more efficiently. Describe your own hands, the drywall cabinet is not so difficult. To begin with, you will have to make a project, acquire the appropriate materials. After that, the framework is erected, it is trimmed with plasterboard sheets, executed finishing work. Shelves for such a closet can be made from different materials, in the presence of experience, it is recommended to conduct wiring and mowing small lED lightsthat will perform the role of backlight.
The partition cabinet made of drywall do its own hands will cost much cheaper the works of the master.
Plasterboard differs numerous advantages, among which:
So where to get started on the building of the cabinet? It is important to have a drawing and assembly scheme in your hands. Today I find such schemes are not a problem. Suggested already ready solutions, among which you can choose the most suitable. If there is no such scheme, it can be ordered. When selecting the drawing, it is necessary to consider which sizes is the room and the place where the installation of the cabinet is planned. The drawing shows all sizes, the position of the shelves, the door, drawers and other things.
When the drawing is ready, it is necessary to proceed to apply markup on the surface of the floor, walls, ceiling. The lines for the guide profile are noted, it is done with the help of plumbing, construction level, metal line and pencil. If there is a need, part of the finishes from the walls or sex are cleaned, although usually no such measures are required.
Back to the category
For the frame assembly, a predetermined drawing is used, it is impossible to start working without it. The design of metal profiles, specially intended for drywall, is not recommended to choose a tree, although it is possible. Wood should be carefully dried, to handle the antiseptic, and there are no such problems with a metal profile. If using wooden bars, when drying, they can deform. Not always the framework racks are able to withstand the load. Therefore, it is better to pay a little immediately and acquire metal profiles. Steel galvanized, aluminum are not always suitable for such work.
Fasten the frame on the marked lines. The first profiles to the ceiling and the floor are mounted, after that the guides are already installed. Wash between vertical racks do not need to be done big. After that, the suspensions are mounted to which the structures will be mounted, they are installed in the guides on the floor and on the ceiling. In those places where the design will touch the wall, use a special sealing tape. This allows you to make a frame more reliable, prevent deformations during operation.
Horizontal profiles are applied to provide additional stiffness, they are fixed on the racks. All fasteners are carried out using metal screws. During the assembly, it is necessary to prepare and guides for boxes, providing regiments. If large loads are assumed, it is necessary to further strengthen the racks and guides.
Back to the category
The walls of the walls are simply performed, for this it is necessary to post and cut the sheets. This markup is made after the frame is ready to avoid unnecessary material costs. Marking is applied simple pencil Both the ruler, the cut is performed with a sharp knife, a hacksaw or an electric bike. After cut, all edges carefully handle so that they are smooth.
Plasterboard sheets are fixed on a frame of self-drawing, the skin is installed quickly. Self-tapping heads during fasteners need to be slightly to completely draw, they should not perform above the surface. During operation, it is necessary to observe accuracy in order not to damage the surface.
The procedure for the work is not limited, but it is best to start with complex, hard-to-reach surfaces, after which it is to carry out the cover of the main part.
This will speed up the work, make it better. After necessary construction level Check the horizontality and verticality of all designs again. If everything is in perfect order, then you can proceed to the finishing stage, which includes training and decorative work.
Back to the category
The finishing stage of the manufacture of the cabinet of the sheets of GLC is a surface finish. There are many options, it all depends on which requirements are imposed on the surface of the furniture, what is the style of the interior. Before starting the finish, the surface is required to prepare. For this, all the joints of the sheets and the fasteners are put off. Typically applied 2 layers of putty. 1st - on the joints and location of fasteners with a narrow metal spatula, literally pressing the mass. Next, you need to use a special reinforcing tape, which prevents cracking during drying, after which it is applied with a 2nd layer.
When the 2nd layer is dry, it is necessary to clean the surface from excess so that it becomes perfectly even smooth. After that you can already perform decorative finish. Here you can show your fantasy fully. The simplest is the staining of the surface (Fig. 2) or gluing wallpaper, but can also be applied decorative plaster. It all depends on the overall interior and whether it is necessary to single out the design or, on the contrary, hide it. For corridors, the option is suitable tile. For the latter option, it is necessary to provide a more durable profile at the design stage so that it is able to withstand the weight from the tile.
Back to the category
To make your own hands the cabinets partitions from drywall, it is necessary to prepare materials and tools. Nothing is expensive and difficult, but before buying you need to carefully calculate everything. For convenience, the drawing is preliminarily drawn up. Profiles, plasterboard sheets and fastening elements are calculated based on the size and features of the design. The presence of shelves and doors, drawers, are envisaged.
Tools necessary for work: construction laser level, Pencil, perforator, screwdriver, scissors for metal, metal spatula.
Of the tools and materials for work it is necessary to cook:
Sliding door-coupe is best to order separately, such services are provided today with many furniture factories and companies engaged in the installation of built-in furniture. It will not only cost cheaper, but also better, since it is not always possible to build such a door with your own hands so that they do not flip, did not fall out.
A person needs a personal space to feel comfortable in own home. Let it have a small corner, but insulated and, to some extent hidden from prying eyes. The closet partition copes with the task of effective zoning.
The cabinet will turn into a partition, if it is put in the middle of the room. Such a judgment is rude, but the tenants of the Soviet "Khrushchev" did that. In this way, the "room" was separated from the village of Student, the "cozy nest" for the newlyweds and a corner for friendly gatherings. If earlier in the closet, the partition was seen only practical importance, now this is a designer reception.
Apartments of dynamic people who value comfort are performed in the style of minimalism and functionalism. Here, furniture, in addition to the main purpose, performs an additional feature. Combined and embedded structures are welcome.
An example of a radical permutation: replace the compact locker to zoning the room cumbersome cabinet along the wall. The apartment will be lighter and more spacious, and places for storage of things - more.
Erecting stationary partitions requires overhaullike dismantling. Planning such a project, it is already difficult to decide on redevelopment, even when identifying errors. For furniture partitions there are no such problems. These are mobile designs, and modular options are also transformed. For the studio apartments with a good solution will be a wardrobe with an integrated TV, installed as a functional partition between the kitchen and the living room. The lower shelves may have a sash, and the upper is better to make through. So the sun's rays will fully illuminate both zones.
To divide the living room, the cabinet can be used as a temporary partition. The design is installed on the wheels and is located along the wall, and in the evening or on the occasion of the arrival of guests overlap part of the room.
In constructions to order it is easy to realize bold designer ideas. Individual projects reflect the character of the owner: restrained and laconic, spacious with large and deep shelves, open racks with a chaotic arrangement of shelves of different sizes.
1.Scaph coupe
Reliable and durable design on monorails with metal rollers. Sliding doors are made of photo printing, mirrored panels, matte glass. The use of a double-sided cabinet compartment for partition allows you to create two separate storage locations.
Selecting the doors in different design, the design includes in zones with different styles. When delimiting the bedroom and children's room from the side adult zone Mirror doors are installed, and from the side of children's - with bright floral patterns.
2. Built-in wardrobe
A complex and overall design completely overlaps the passage and has a doorway. It consists of several blocks. The design of plasterboard includes a frame of a metal profile, which is attached to the walls, floor and ceiling. The blocks are present with sliding doors, upper cabinets with hinged doors, lower retractable sections, open shelves for books and decor. From the cabinet furniture, partitions with high noise insulation are obtained.
3. Cabinet with additional retractable mechanisms
In one-room apartment it is important to maintain an open space, not forced by furniture. In tempting look like ideas with a folding bed or a retractable computer table. Mechanisms increase the cost, but stylishly look at the kitchen combination - combination with a tea table or bar, aphrodium for aquarium, a colors stand.
4. Two-way cabinet
The deaf wall is not allowed in the zoning of the room. Double designer cabinet is represented by a compartment or rack partition. If the area allows, on the one hand, they make a normal depth of 60 cm, and on the other, it is reduced to 30 cm. As a result, the partition is obtained by a width of 90 cm. This is a lot for small-scale apartments, so the owners choose the shelves with shared access.
5. Wardrobe Stellazh
Open shelves and high racks are indispensable when the room is zoning with one window. Such structures skip the light and make the room more spacious. Racks are suitable for dividing the living room and kitchen, where the task of complete visual insulation is not set. Each kind of designers determine their purpose in the interior. In some cases, the partition becomes the center of the room, and in others - invisible.
Before carrying out the separation of the room to the zones using the cabinet, you need to think about the partition to affect the interior. A small area use open racks or a cascade of modular elements. Closed massive cabinets to the ceiling climb the room and create a feeling of cramped.
The bulky double-sided cabinet as a partition will be appropriate between two spacious rooms. Such furniture takes useful meters, but it is not noticeable on a large area.
If the room is cut into the room without a window, then the upper shelves are made through and without doors, solar rays. Also, they cannot be forced boxes and large decoration. Another option is furniture with human growth or lower.
Filling for children make ergonomic. Large and high shelves will fit large toys and educational books.
Installing instead of walls in the room built-in wardrobe with coupe and entrance doorIt is used and as a full partition, and as a dressing room. Manufacturing and assembling such designs is better to entrust professionals.
Multifunction cabinets are not appropriate if the bathroom zoning or a narrow bedroom is carried out.
Complex designs will require noticeable financial expenses.
With full blows, the passage is placed in the closet, sometimes hiding sliding doors, otherwise the partition will not give the necessary noise insulation. An attempt to save on the material and the mechanism will be wrapped up rapid wear.
For close rooms, narrow racks are selected, because they are lungs and occupy little place. Such a lightweight design is unstable and requires fastening.
Classic zoning cabinets occupy large square. To properly plan and avoid gross mistakes, consult your designer. An experienced specialist will be able to catch all the nuances of your apartment, which are already invisible for you.
People often have a task to divide or a regular room for several zones, but to install bulky walls of bricks, drywall or wood is not possible. Maybe this is a removable housing or a shortage of finance - it does not matter, but it is necessary to solve the problem. There is a simple and more accessible output. Couple wardrobe, ordinary cabinet or simple rack in skillful hands is the same functional partition. By setting the listed things in the right place, you easily share space without arranging troublesome roads.
 |
 |
|
Double-sided wardrobe is usually chosen for the premises that need to be overcoiled. For example, that optimal option For the children's room, where there are several children of different ages or one-bedroom apartmentswhere the big family lives. Contrary to many concerns, such permissions not only does not reduce the living space, but also visually makes it more spacious.
The closet partition zonizes the room, serves as a storage location and looks very effectively due to an unusual design. You can make it not only for clothes, but also for storing books, children's toys, placing television equipment and a lot of other. On the one hand, it can be a classic cabinet, and on the other hand library or video. Furniture-transformer is optimal even for close apartments, because it makes an unnecessary purchase of chest of drawers, Tumb, shelves and many other things.
Double-sided wardrobe - this is:
The wardrobe can be embedded in the niches in the walls, if any, either split the room with a classic way. The partition from the cabinet is also called interroom, because it may well blame one living room into two full rooms.
Do not fulfill all these works on your own. There is a risk of incorrect zoning and excessive bells of space. It is best to order a double-sided cabinet in a good company, and it will do all work in 2-4 weeks.
Double-sided cabinet - optimal choice For the studio apartment, where the kitchen and the living room are combined. You can burn out the smells of the kitchen with an elegant cabinet, which, besides, will help solve all problems with storing things. Perfectly suitable similar furniture And for the hallway, if, for example, to demolish part of the wall and replace it with a closet partition.
Advantages of double-sided cabinet:
Double-sided cabinet models are actively used in Japan, so as external decoration Often choose bamboo or rattan or photo printing with the image of Sakura or Garden of stones. Best choose harmonious design both sides of the cabinet, and not dissoning with each other. If you use a tree, matte glass or other natural materials, then the second side of the cabinet must be appropriate. The exceptions make up cabinets for children, where each of the living children can have their ideas about decorating.
You can place the order of the two-way cabinet in our company, which is located in Moscow. You can choose the photo option in the catalog or develop your own individual project. In any case, the solution for the choice of furniture design, internal filling will always be yours. However, given the complexity of the model and the fact that it actually becomes part of the room, it is still worth consulting from experienced designers.
Want to know the cheapest redevelopment option to the stylish designer living space? The answer to the question is simple - the wardrobe is needed here.
Remember, our grandmothers stood an old wrapping monster, which was destructed the bed from the rest of the room? Now designers offer a similar option, but in an ultra-modern version.
Sooner or later at the owner small apartments There is a thought that it would be nice to get a comfortable bed instead of a folding sofa. Or he will acquire a family and the need arises to highlight the area for the destruction of children. In this case, install the wardrobe partition, sharing the room into two parts, - perfect solution. But with this division, as a rule, the window remains only on one side of the cabinet, and in the separated zone does not penetrate the light. This is solved by embedding LEDs into the cabinet case.
Some people install such a wardrobe instead of a wall at the junction of two rooms.
You can decorate the facades by any materials based on the budget, preferences and interior style. It is worth noting that the mirrors visually expand the space, and the doors with the photo printing will be given the mood of the whole room.
