For quick and uniform heating of the room, you can use the buleryan furnace (Buller, Breneran). Region of its use - residential and production structures, greenhouses, shops, warehouses, country housesCottages. Distinctive trait This mechanism is that warm air does not accumulate around it only. Opening everything interior doorsYou will access heat in all rooms.
The braneran furnace is invented by Canadian engineers, which as a foundation took the drawings of the convection-tube boiler of slow burning.
Buleryan - a device of domestic production.
This is an all-welded design made of steel. On the sides, it is wicked by a large number of pipes. It has a stack with a wide hermetic door, equipped with a confusion, made in the form of a pipe with a turning point (choke). It is with its help that the power of the heating device is adjusted, the process of heat energy is controlled, the required temperature is set.
The device of some booleric models is equipped with a graded scale and limiter. If you need to stop the operation of the device or stop the craving, the choke overlap. Below are the drawings of the furnace.
At the bottom of the furnace is steel under or cast iron grille, at the top of the structure - a horizontal partition with holes that does not reach the front wall about ¼ of the fuel length. Air for afterburning is closed from there.
The upper space, isolated with a partition, is a survival chamber when operating in mode. Going from there gases go to the horizontal segment of the chimney, called "Borov", its length is 0.8-1 m.
The burning mode in the stove of the brandaran switches using a smoke choke (chieber).
Boilers have a chimney with a diameter equal to the size of a puddle. In the smoke throttle flap cut 1/4 part. Such a device does not allow to stop the thrust, in any case will be released into the pipe.
Economyzer is located above the smoke throttle. This is the vertical section of the chimney, well isolated asbestos. It is designed for driving flue gases. Oblocked, they are trying to expand, which contributes to the formation of a gas cork. The combustion process decreases, the cooling plug in the end disappears, the combustion increases.
Thanks to the economizer, this device has an efficiency of 80%, without it - no more than 60%. The operation of the buller without this element decreases to 2-3 years.
This heating device works as follows: cold air from the floor, entering the connected nozzles, passes through the elements located on the furnace.
Heaving, it comes out of the upper nozzles and evenly heats the structure. After 10-15 minutes after the extracts of the design, the air in the system heats up to 100-120 ° C.
Unlike classic heating devices, brandage boilers take the air for hurrying from the furnace. For the secondary air masses of individual phones. The amount of air automatically changes depending on the type of fuel and the mode of operation of the furnace.
The second raisin of the buleryan furnace lies in the design features of its furnace. The batteries of the heat exchanger pipes are made in such a way that on 2/3 they are drowning in the curvilinear walls of the furnace. Due to this, up to 70% of the heat released in the combustion space in the mode, are given in the air of the pipe system. 10% of thermal energy is distributed over the metal body of the instrument and also heated air.
You can damn the boiler with wood waste or residues from the cardboard products, firewood. It is impossible to use stone coal. Fuel in a similar device is consumed slowly and economically. The bookmark it must be carried out not more than 3 times a day.
To quickly warm up the room, it is necessary to initially lay the fast-burning fuel in the stove, paper or cardboard. They are burned, while the choke and the Sewber should be discovered completely, and the door of the furnace is closed. The acceleration laying should completely turn over 3-4 minutes. You can control the process of burning through the glass in the door or threatened.
After burning bookmarks, large lamps are laid, peat or pellets. The choke pissed down to the required position. Schieber must be closed on ¾, that is, until it stops. From the pipes with air temperature of 60-70 ° C, the furnace cools up to 50-55 ° C.
In addition to the fact that these heating boilers provide fast and uniform heated at home, they have other positive properties:
In addition, you can make a bike buleryan with your own hands.
Such a device needs insulation of outer pipes. To place it, you need to highlight a significant space. In such a device, the fuel combines with a minimum residue, as a result of which he smokes, so the pipe has to withdraw a height of more than 3 m from the top level of the furnace.
Also, negative qualities include the appearance of condensate in the chimney and the smell that may appear in the room.
In order for the private house's heating is reliable and high-quality, the boilers with water contour often use. They are heated due to movement in the hot water system. Such a device is a cylindrical housing that consists of 2 levels. The lower is a flue design, its purpose is the fuel ignition and temperature control. The top level of the boiler with water contour is a gap surgery.
The purpose of the unit is the heating of water in a large volume. It is equipped with special devices that distribute about 10% of thermal energy to heating, and the remaining percentages for heating fluid entering the system or drive. Thus, private houses are provided with appropriate temperature conditions.
Copper with water contour It is necessary to fill with distilled water and antifreeze. Then the system will be protected from freezing, if the house does not live constantly.
Water Buller drawings are presented below.
Make the bake of the buleryan with their own hands hard enough, it is necessary to be an experienced welder.
To make the boiler, the drawings of which are located below, require the following tools and materials:
welding, Bulgarian, metal cutting scissors, tubular, hammer, thick-walled pipes (diameter - 50 mm), metallic corner (25 * 25); Metal sheet (thickness - 5 mm).
Check the operation of the device for welding work, materials for weldability, work in the manufacture of seams.
Here are the drawings of the Breneran furnace.
The boiler has posted low power And it can be used in garages, greenhouses, hospostroy. For the heating of a private dwelling, it is necessary to increase its parameters and the number of pipes by 1.5-2 times.
You can make the furnace on your own, sticking to the next specific sequence of work.
The ovens are chosen depending on the area of \u200b\u200bthe room. They have a design at a distance of at least 1.5 m from the wall. It is lifted above the floor (this will increase the force of thrust and heating rate), setting on the podium from non-combustible materials. To avoid fire from falling sparks and coals, a metal sheet is put under the furnace. Installing the bake of the buleryan is better in separate rooms to accidentally do not burn.
With the rise in price of gas and electricity, the word "buleryan" began to meet more and more often. For places where state heat sources are missing, Buleryan is a desired dream. If you believe advertising, then there is nothing more economical and more convenient. Is it really? Consider all the advantages of this heating unit, as well as its underwater stones, that is, flaws.
The article present useful reviews of the exploiters of this unit, which will help you avoid many mistakes and more likely to learn about Bowleryan.
Buleryan is a solid fuel stove that heats the room on the convection principle. The roots of this furnace, whose analogues today make everywhere, go to a simple Canadian logger. But the license for furnaces on this project belongs german company "ENERGETEC GMBH". And on the Russian expanses there is an analogue manufactured by the German license - "Breneran" from Laoterm CJSC.
Externally, it is possible to note the similarity of the buleryan with burzhuyk, but it has a great potential for heating the room. It is a steel barrel that has a bunk fiber, which is enveloped from 7 and more air pipes. The design also has in itself everything that other furnaces - a furnace door, an air supply regulator and a smoke damper, but there is no pallet for cleaning from ash.
High efficiency is due three ways of heat exchange:
Buleryan is a device that combines three functions immediately - directly furnaces, a carrier and a gas generator.
The work of the bulery furnace is based on the principles of dementia Woods in the lower combustion chamber, followed by the release of gases. They are called generator gases, because, burning they are able to generate a lot of additional heat.
E.ti stoves can not be called an aggregate, which "squeezes" all potential energy from generator gases. To do this, there must be a special catalyst and air supply under pressure, and in addition, the temperature is much higher than the mark that ordinary bulene gives.
Buleryan works in two modes:
Important! Buleryan issues the promised efficiency only when using dry wood material, which there is a lot of generator gases during combustion.
To appreciate the bake of Buleryan to the fullest, will pay attention to its positive and negative qualities.
Of the written previously seen some indisputable pluses Works of this furnace, but we grouped all the characteristics that are spoken in favor of Booleryan:
Now about those arguments that can be attributed to negative sides Furnace works:
As you can see, what is the principal idea of \u200b\u200ball the analogues of the buleryan furnace, namely burning along the type, at the same time causes and weight side effects.
Sauce, tar in the pipe and the burning of dust are the main problems that the exploiters of these heating units faced. How users respond to these problems, and what solutions they find them to minimize them, you can read in reviews.
The third year with a bulery and very satisfied. Our discharge oven 02 is heating 300 cubes. For 4 hours he warms the house to +18 at a temperature on the street -25. After the house is warm, overlapping the air, and it works on one bookmark about 10 hours and 1 hour cools. We have less consumption of firewood than that of neighbors who drown in the furnaces of other structures, 1.5 times.
There are several drawbacks:
A) I tried to pull the adjacent room through the corrugations, as the manufacturers write, but no normal air circulation turned out. Some familiar for this purpose set channel fan, It is said that the effectiveness has grown and heating goes faster. True, the fan is noisy, and the air vents around the house are minus, although there is for what to suffer. Well, we just open all the doors in the house and so good the entire cube is oppressed.
B) for me a substantial "bonus" from the work of the buoyanchik - clusters in the chimney pipe and emission is flying to the roof. Moreover, these sediments can periodically flamm in the pipe and therefore need to follow this case. Despite the fact that I have a trumpet-sandwich, it is very warm at such ignitions, so you need to regulate. But this nuisance, as they say, we will survive.
In general, we are satisfied and the best alternative gas boiler not.
User Moscow, Domochea Forum
The fifth year to Kochgarim Bowleryan and everything is fine. And it turned out to be with us so - my husband gave this miracle to each other, since it was wrong I was installed and could not coat. They made too low chimney, and this could not do this.
It is designed for 100 cu. m., but we have only 50 cubic meters. per hour heats up to +15This is despite the fact that in the room it was up to that -7 (specifically sequel). At night, we dislike the thick logs and they burn until the morning. It stands at night on the mode, we sleep quite normally. Tried to drown and dry sins, heated the room to a complete Tashkent. We like that leaving him can be left like this - close the damper and he himself will go through time.
Raw material and truth is burning perfectly. Be sure to clean the pipe at least once a year.
By the way, the neighbor laid down a buleryan brick and says that he now keeps the warmth longer.
User forum about the bulery furnace
Most likely, many users of this furnace face with condensate problem in chimney pipe. Some are despair, meeting with difficulties, but many still find the causes of problems, eliminate them and share with others:
I will tell you how we walked with the speed condensate in the pipes - two weeks and the pipe is clogged under the urban. Pipes burned like matches ...
The whole problem is that it reacts even on a slight cooling of the pipe. And we had a pipe through the wall in the kitchen and on. Horizontal trumpet i was scored not soot, but coke. It turned out that the kitchen without heating and there is colder than in the rest of the house, and significantly. Therefore, the condensate accumulated in places where there was a craft for cleaning, that is, just a gap and a brick is inserted. We corrected this thing: the metal pipes were insulated, the cracks in the brick strokes were embellished asbestos. And it became pretty good!
And yet, the pipe was short, and there was a fly on the roof. Now we have been taped there something like a attic and a pipe has become as many as 8 meters - now I think nothing like that will not.
Nikolay, Dachnik Forum
Tip! The exhaustive advice from specialists does not say that it is necessary to use pipes like "Sandwich" or insulated pipes heat insulating materials. However, it still does not cancel the fact that the buleryan will have to recall from time to time.
Also members of the forum are divided by the doctors to clean the chimney:
I am a pipe clean the cable for cleaning the sewer, only it needs to "fluff" at the end. I have a cable for 10 meters, which consists of a variety of lived. Cleans this device is just fine.
Reply to the Internet Forum
Some users are quite detailed experience in the exhibition of pipeswho will come in handy many wishing to have a buleryan:
I have a type of type 01, which I heating 70 m 3. Refunnant, I am satisfied with the third year. True, the pipes had to change, since in 2 years the galvanized pipe was across sulfuric acid, which is in condensate.
After it, I installed a special thermotrub with an internal stainless steel AISI 304 thick 0.5 mm thick (enough) - resistant to acids and heat-resistant, Outside galvanized. Inside this design of the type of sandwich is naked mineral wool. Outcome: Insulated pipe almost does not collect soot and condensate and burning has become much more stable!
About long burning, then my dry acacia is burning up to 10 hours a maximum, but the pine is burning like a match - 2-3 hours.
User of Nikolaev, Forum Masters
At the expense of "omnivities", the buleryan also hosts many stories, in which it is written that this unit takes everything that burns - from being covered to the tire, but this is not quite so. Perhaps it applies to garage heating - I slept and left, but not for heating at home.
In the first year, the pine trees, because it was a lot, as well as all saint garbage: old painted windows and platbands, boxes, and so on. But it was extremely, firstly, there were often outbreaks from the fact that gases were gathered in the chamber and suddenly lit up, the smoke went into the room. The error was still that I decided to save the first one and a half meters of the 6-meter chimney did without insulation, so that inside the room was also from this segment of the heat transfer. Bad fuel plus this puncture - for this season chimney was completely scored. Now abandoned pine and garbage fuel, using dry aulh. One bookmark is enough for 12 hours - I have a buleryan 03.
User Mr. Radomyshl, Forum Masters
No matter how the manufacturer's advertising product praises, he still has some nuances that someone calls disadvantages, and someone features of work. Rate all the "For" and "Against" buleryan furnace, reading the presented reviews and video of this furnace. If you agree once a year deal with cleaning pipes, as well thoroughly work the chimney pipe, then you can seriously think about the purchase of Bowleryan. Remember that for its use you need a permanent stock of dry wood.
The heating unit developed in Canada specifically for mobile brigades of lumberjacks has won recognition worldwide due to high efficiency and safety in operation. The Bullerjan wood-burning furnace (Bullerjan) is used as a heat generator for air and water heating of private and country houses, household buildings.
Burnjan Oven (Breneran)
The task of the designers was to create a compact and light solid fuel unit capable of quickly slowing down the room. At the same time, it was important to ensure simple control of the work of the furnace, take care of security - minimize the risk of random burns and eliminate the penetration into the carbon monoxide. Consider a detail the device and the principle of the Boolery.
The cylindrical or chopping body of the stove is equipped with built-in curved duct tubes. The main part of each pipe is located inside the housing and is heated by the flame. From the bottom end of the pipes is suused with cold air, during the movement up, it has time to warm up. On average, the stove pumped 4-6 cubic meters of air per minute, quickly heating the room.
The furnace chamber is divided horizontally to three compartments. In the central, incendants, fuel is stacked. In the lower compartment accumulates ash. The top compartment is separated from the middle sheet with the holes - it serves as a secondary chamber for burning pyrolysis gases, and they burn there not completely - the final afterwards occurs in the chimney pipe.
The furnace housing is equipped with a hermetically adjacent widescreen door. It is equipped with a nozzle with a damper - the throttle allows you to adjust the intensity of fuel combustion by changing the amount of air entering the furnace. To adjust the force of thrust on the outlet of the furnace, the gate valve is mounted. Setting the work of the furnace is produced by changing the position of the flaps.
Constructive features Furnaces buleryan The Bullerjan stove in the original design is equipped with an economizer - a device that allows you to show up pyrolysis gases to get a maximum of thermal energy from the fuel. The heat generator with an efficiency of the efficiency reaches 80%, without this device, the furnace efficiency is about 60%.
The secondary burnout of the combustible wood gas occurs on the horizontal section of the chimney (from 15 to 30 cm), which is securely thermally insulated with non-combustible material. Due to the accumulation of gases on this section of the pipe, the temperature of the medium increases and the flame flashes regularly, the combustible gases flare up, increasing in volume. As a result, a gas plug is formed and the combustion stops without access. Next, the process is cyclically repeated. The frequency of gas flareness depends on the installation of the furnace.
The air-heating furnace of the buleryan is completely safe - even if you leave the windshield door open, the carbon monoxide will not enter the room. The metal case during the operation of the unit is heated to 50-60 ° C, so contact with the furnace does not threatens to a person with a burn.
If you mount the air ducts, you can feed the heated air into the neighboring room, providing air heating.
Buleryan in combustion mode works only at the first stage - for 20-30 minutes after the ignition. During this time, the room has time to warm up. During the rest of the time, wood fuel should be twisted, highlighting combustible gases. If the unit is forced to constantly work in intensive mode, the metal case will quickly priece, while a significant part of the heat will be disappeared with smoke gases.
Heating of room furnace Breneran When burning oven, it is important to use dry, fast burning fuel. In the process of ignition, the choke and the gate valve must be open to provide high traction. When the first fuel laying turns into coals, put large-format firewood or briquettes. Having laid the firewood into a warm oven, it is necessary to cover the girlfriend and the throttle, adjusting the air intake.
Attention! The furnace in Vullerjan is not designed for the firing of brown or stone coal, anthracite because of too high temperatures combustion of such fuel.
Installation of the bulery furnace is performed in accordance with fire requirements. It is important to observe the distance to the walls, which depends on the surface of the surface:
Heat chamber diagram for heating unit The base under the bake of the buleryan should be non-combustible. The podium is laid out of the brick or simply fit on the floor of the sheet of steel on top of the non-flammable heat insulator. A steel sheet in size 500x700 mm must be located in front of the door of the furnace furnace for air heating.
Installation of the bulery furnace requires competent chimney pipe mounting, it can be:
The height of the pipe depends on the power of the heating unit and is indicated in the passport of the product. The minimum height is 4 m, the minimum cross section is 120 mm. The chimney is allowed to withdraw through overlaps and through the wall with the installation of the heat insulated passing unit.
Buleryan with water contour (Breneran Aqua) is a modification of an already known furnace, which is designed to operate in autonomous water heating system To warm up several rooms in the house.
If air heating Installation First of all, it is intended for small country houses, garages, workshops and greenhouses, the Boolery of Aqua is a full-fledged boiler that is suitable for organizing the heating of an individual residential building.
Buleryan with water circuit in design is similar to air option The stoves, but in this case, by pipes, a fuel combustion chamber, circulates the coolant.
Stove Breneran with Water Contour The boiler functions as follows:
Breneran Aqua also works in wood fuel, thermal energy It is mined by direct combustion of fuel and burning pyrolysis gases. Combustible gases are burned in two stages - the main part in the upper chamber of the furnace, the remaining - in the economizer, which is equipped with chimney.
The most energy efficient fuel for Aqua Breneran is wood. It is allowed to use peat briquettes, extruded woodworking waste, but their thermal returns are lower.
Buleryan with water circuit has several advantages over the heat generator of the same type, but for air heating and other units:
Breneran Aqua with water loops The disadvantages of Aqua Breneran can be attributed:
In accordance with the rules of fire safety:
Rules for installing buleries If the water loop bulene is connected to the gravitational heating system, then to effectively circulate the coolant required:
Attention! When calculating and installing the pipeline, it is important to observe optimal angles Tilt of pipes to ensure the normal movement of the coolant and avoid the formation of air traffic jams.
If the furnace is used as part of the system with a coercive coolant feed, it is necessary:
Diagram of a buleryan device with water circuit For the strapping of furnaces Breneran with water circuit, pipes are used from different materialswhen choosing should consider them operational properties and installation features:
Polypropylene pipes and fittings for strapping heating system The coolant in the heating system based on the heat generator Breneran with water circuit can be the usual or distilled water, non-freezing fluid.
Water is a cheap and affordable coolant. Its disadvantages include the properties to freeze at temperatures below zero degrees. Water is recommended to fill in the system if it is designed for non-stop operation in cold period of the year. As a coolant, it is impossible to use water with a high metal content. It is desirable to establish a system for filtering and water treatment. Installing a special tan will help avoid problems associated with the defrosting of the water circuit.
Non-freezing liquid is suitable for heating systems that winter time years are operated with interruptions. The use of antifreeze makes it possible to survive a decrease in temperature in the house to -20 ° C. The minuses of non-freezers should be attributed to high fluidity - increased requirements for the contour tightness. In addition, the cost of antifreeze is significantly higher than the cost of water. To calculate cash investments in the purchase of non-freezing coolant, it is required to calculate the volume of fluid in the system. For this, the volume of the pipeline, all radiators and the water contour of the furnace are summed.
The type of the stove of the buleryan is selected depending on the needs - for dacha house Or economic structures easier to use air heating unit. In a house with several rooms, including on different floors, it is more convenient to use the braneran boiler.
Gas-generated long-burning furnaces have gained great popularity in countries with a harsh climate, where the temperature below zero degrees is kept for several months. Inexpensive, reliable and economical. And if such an oven has a water circuit, then it becomes indispensable. After all, it can be used, as for air heating in a residential or production roomSo for heating at home, cottages or garage.
Let's analyze the main species presented on russian market, on the example of the stoves of Breneran-Aquategen or Aqua Breneran, having different reviews from the owners and the liveshchers. And also consider them specifications, principle of operation, the lineup and prices.
This is probably the most famous and popular furnace of this type. The basis was taken by its prototype - this is (buleryan). Then the engineers were somewhat finalized and, holding a heat exchanger in it, made it possible to use it not only for heating the surround air, but also for heating the heat carrier in the heating system.
Device of the furnace Breneran-Aquategen (Fig. 1)
The housing of the stove is welded from steel and covered with heat-resistant enamel of black. Inside this furnace, there are two combustion chambers: upper and lower. In the bottom chamber, the process of producing gases from solid fuel, and in the top - after hurrying these gases, with subsequent heat generation.
On the sides are 2 collectors with built-in injectors. Two chiebers are installed to adjust the power and mode of operation on the furnaces: in front of the door (4- Fig. 1) and on the chimney nozzle behind (3.5- Fig. 1). For the supply and output of the coolant on the unit of the unit there are two threaded collectors (1.2- Fig. 1).
The chimney diameter can be different, depending on the type of aqua-brande: from 120 to 180 mm.
Furnaces Aots Breneran-Aquatene are several types:
- Aots-6 Type 00
- ADOT-11 Type 01
- ADOT-14 Type 02
- ADOT-16 Type 03
- Aots-19 Type 04
They differ from each other with dimensions, power, combustion chamber volume, weighing. It is selected on the area of \u200b\u200bheated room. The smallest eats up to 100 m3, the largest to 1000 m3.
Specifications Long burning furnaces with water contour Breneran-Aquategen
Specifications Breneran-Aquategen
For the Brenran-Aquatance furnace, almost any solid fuel is relevant: firewood, peat, cardboard, chips and sawdust, except coal and coke. It must be remembered that for proper work Such a stove, you need to ensure that the lower chamber can be completely filled with fuel. In this case, the manufacturer guarantees work on one of the hard fuel laying up to 8-10 hours.
Using the water contour of the furnace Breneran
Such a snack of long burning can work both in the open and in closed systems Heating. For a closed system, it is necessary to buy additionally and set the following equipment:
- circulation pump
- Membrane expansion tank
- Safety Group (Safety Valve and, and Pressure Gauge)
For proper application Furnaces in systems with natural circulation It is necessary to observe a certain slope of the pipes of the heating system. As well as an expansion tank open typeTo be placed in the upper point of the system.
Everything is shown in more detail on the photo diagram below.
Furnace installation scheme Breneran-Aquategen in open system Heating
Advantages of the Breneran-Aquategen-Water Contour furnace
- High work efficiency in long-burning mode
- Ability to work in open and closed heating systems
- Ability to align with, without reworking the old system on plastic (polypropylene)
- Democratic price from 15000 rubles
Disadvantages of the furnace Breneran-Aquategen
TOTAL
Long burning furnace with water circuits Breneran can be suitable for rooms of different volumes. But at home such a furnace will look not very aesthetic. For it, a special boiler room is ideal, it is also possible to use it for heating the production workshop or garage, etc.
For the heating of a private house, I would still advise to consider others, more modern options long burning furnaces with water contour. For example, domestic has proven not bad. Or consider imported analogues, but in this case the price of the furnace will be higher, and significantly. Therefore, you will have to choose. And, finally, small video overview.
If not going to unnecessary details, the water loop bulene can be characterized by several words. In essence, it is a design of high-quality metal with pipes welded to it. A feature of this device is that it contributes to convection, that is, uniform and very rapid warming of the entire room.
Outwardly, the whole design is a boiler in which wood materials need to be placed. Since such a furnace can work exclusively on wood fuel, before purchasing it, you need to understand how profitable it will be. Since in big cities this natural material It is quite expensive and you need to go to specialized stores.
Buleryan with water contour is a furnace that works on the well-known law of physics. The whole principle of its work is that the hot couple rises up, and the cold goes down. Thanks to this feature, even the smallest stove with a water jacket is able to warm up more than five cubic meters of air. At the same time, the boiler is not increasing, that is, the room does not lose its oxygen.
Buleryan is considered an economical furnace, since fuel costs can be reduced.This is due to a special survival chamber, in which all the gas obtained during the combustion process is burned. As a heat exchanger, a casing is used, some manufacturers call it a shirt. Inside such a casing is at least six pipes, which are tightly adjacent to the ceiling chamber. As a result, it is possible to observe that heat is much faster than the water.
A coolant is served in the upper point of the entire heating system. After that, it goes to radiators and back to the oven. It is there that the crane is installed to drain the coolant. Thanks to simple principle Works - Booleries are able to quickly warm up any room and not dry, while all oxygen.
Each furnace has a number of indisputable advantages over others. Very frightened from where it will be installed and what spent the buyer agrees. It is necessary to understand that the furnace itself costs a lot of money, but its operation will not be free.
The main features of the stove of buleryan with water circuit:
Due to the special location of the pipes, the boilerian increases the heat transfer. Cold air comes to the lowest tube. Heated to a certain temperature, it extends all over the room. Note that, unlike other furnaces, which work with the help of firewood, at the buleryan, the design is thought out to the smallest detail. Not only firewood is burned in the furnace, but also fire products. Therefore, to achieve the desired result it will be necessary to use less natural material.
Note! To date, there are only two options of the buleryan. First works to meet the needs hot water, and the second at the same time on heating and water.
To date, the water contour is not difficult if it uses the necessary methods and materials for this. Before the installation itself, you need to decide on the place where the furnace will be installed. Note that it can be put almost anywhere in the building. The only thing to do is to keep the distance to the wall in the length of the half meter.
Water heating scheme with boiler
After installing the furnace, it must be connected to the heating system. During installation, most professionals recommend using reinforced pipes. They will never be deformed under the influence of high temperature, as well as most suitable for the heating system.
At the end of the installation of heating nodes, crimping is carried out, as well as filling with the water of the entire system. After that, behind the work of the buleryan - the stoves with a water jacket must be needed for some time. Only as proper montage and its boiler will work properly.
Never forget about security! Therefore, the wall, near which the furnace will be installed, you need to be treated with a special non-aggravated material. It should be applied to a height of approximately a meter from the top point of the furnace.
Before making any purchase, you need to understand how profitable it will be. In the modern world you can find a boiler that will be incredibly beautiful, but very expensive in its use. Therefore, you need to find a balance in aesthetics, price and cost of operation.
The main advantages of the buleryan before gas heating:
Unlike gas equipmentBeerryan does not need to specially care for. You only need to read the chimney and do not forget to regularly put firewood.
The boiler called the buleryan with water circuit has only one drawback - these are the cost of fuel. However, the difference in gas heating costs is not so great. Considering that at the installation and installation phase, it is possible to save significantly - the buleryan can be confidently called a profitable heating option for each consumer. In addition, such a boiler can be chosen decorative brick And create the illusion of an old Russian oven. It will look very stylish, beautiful and original.
