Many designers prefer not to leave the corners in the apartment are untreated and add to the interior unusual solutions For this part of the apartment. For other scenery can serve as protection if there are animals or small children in the house. Fragile angular covered walls requires attention and additional protection. Therefore, this article discloses the question of how to arrange the angles of walls in the apartment, the photo of examples will also be found.
One of the most problematic areas in the interior decoration is external angles.
There may be many reasons for the use of such a building material. In this case, each trace a different result of the work. But most often it is due to the need to align the corners in the apartment. Unfortunately, builders often face such an embassy and have to carry out an additional stage of repair to make the room visually completed.
Decorative corners help these problems.
To make the right geometric shape, it is necessary to prepare a working surface. For this, the previous coating is removed: wallpaper, whitewashes, plaster. Next, the builders are carried out in the form of spraying with an antiseptic and cover the new layer of primer.
Corner protects the surface from mechanical damage, allows you to hide some flaws in the finish, place a transition from one material to another, close the tile ends or panels.
Using a special corner, which is sold in every professional construction store, set the necessary form on the corners of the walls. At the same time, it is possible to measure the deviations and evenness of the surface obtained. At the end of the work at the angle, special metal fasteners are glued and additionally processed the new layer of finishes.
There are many options for using corners in the interior.
After performing small construction manipulations, the angle is fully levels and the necessary visual effect is achieved. In difficult cases, absolutely any finishing materials can be used: starting with plastic panels, ending with plasterboard elements.
Some difficulties occur when finishing angles other than 90 °, for this requires special, so-called. Folding, corners.
In addition to the target to align the surface data construction work Engaged to decorate the surface. A wide range of materials allows you to beat the angles and make them real elements of the overall interior concept.
They can be used to design both outdoor and inner corners walls.
The trim of corners in the apartment provides for the use of various decorating elements. This allows you to achieve completeness and aesthetic attractiveness. Everything else, such manipulations are used to save space.
The angles can perform the role of niches for embedded furniture or fully cut to arrange leisure areas.
Different finishes of the corners are accompanied by appropriate objectives. So, if there are small children or animals in the apartment, the corners are processed in order to additional protection. A sharp effect can deform the desired shape and spoil the interior.
Their use in this case protects the end of the slope from damage and does not give the wallpaper to unwind, which is quite often occurring at external corners.
Amateurs unusual design prefer non-standard corners. It can be embedded furniture or arrangement of additional space. Different building materials can be used as a finish with the purpose of influencing the interior.
Excellent idea for saving a place in the hallway.
Special protective corners are used to protect. They differ from among themselves not only by the method of fastening, but also the place of use.
In addition to the technical, an aesthetic load also carries the angle profile.
The range of such products includes the following variations.
The use of a white corner gives the completion of the window to the window.
The use of corner finishing will allow to achieve several goals at once:
A profile contrasting with slope and wall decoration can create the desired color accent or become an independent original part of the interior.
Depending on the material used, you can achieve different decoration options. Stone finish will make any room unusual. Plastic materials Assist to achieve completion and simplicity.
Silicone can perfectly add children's rooms their abundance color Gamma. and high protective functions.
Designers prefer not to extract the corners, but to clean them. So, additional niches appear at the site of the usual room walls. They perfectly help to save place, because other furniture and even household appliances are inserted there.
Such a "chip" in the interior can be used in bedrooms for bookshelves, in the corridor for shoes and in the kitchen for the technique.
Bold designers practiced to get rid of corners. Instead, they equip an additional deepening, where you can accommodate:
The corner of the room can be transformed into a practical rack for books and souvenirs.
Additional Information! In addition to the above, recesses can be applied with other purposes. Fantasy does not know borders and you can come up with any options for convenience and comfort in the apartment.
Finishing the corners in the apartment with decorative corners - This is not easy process. It costs due attention to pay the choice of material. The overall concept of the result depends on this.
From the material of the corner depend on it appearance, specifications and scope.
Such accessories is an inexpensive decorative material for finishing their polyvinyl chloride (PVC). The building material is highlighted by alkali resistance and acids. Small weight greatly simplifies the installation process. Also PVC panels are not demanding of care.
The monochrome corner palette contains about 30 shades.
When cracking or deformations, you can easily replace the details to new ones. At the same time pleases affordable price. A large range of products will allow you to choose the necessary dimensions, shades and even the form. Key benefits should include moisture resistance and ease.
If necessary, the white profile can be repainted in any other color.
Attractive and flexible material that has found its application in the trim of the bathroom. High resistance to water allows the use of a product in a humid environment of this room. At the same time, the corners themselves are flexible, which allows to mount them even on uneven surfaces.
The main drawback is weakness to household chemicals. Therefore, the process of care for this protective product is complicated. For cleaning it is necessary to use non-aggressive chemicals Or a conventional wet rag.
This material is pretty soft and well suited for rooms where small children are often present, because Reduces the risk of a child to get damage by hitting the angle.
Builders prefer transparent silicone corners due to the ease of installation. The design is attached by removing the protective film that covers the sticky base. No need for mounting optional equipment or mixture.
This material will always remain the leader among others. building materials According to the criterion of aesthetic attractiveness. This option Finishing the corners in the apartment will help create a special atmosphere and emphasize the unusualness of the design solution.
Decor corners in the apartment is best flexible stone.
Such material is relevant to use owners large apartments. Since Sam decorative rock It takes quite a lot of space. In a small place, its installation is considered irrational.
The decorative stone in the corners will look very beautiful.
TO key features It is worth attributed:
The use of stone is appropriate in apartments with a large square.
Universal material that is widely used for decoration arches, shelves, ceilings, walls and any openings. The fragility of the material does not allow mounted in order to decorate the room. When installing, it has to add an additional stage of construction, which includes fixing the design with putty or other mixtures.
Plasterboard is distinguished by affordable and acceptable price.
Now it is clear how to decorate the angles of walls in the apartment. With this construction trick, you can protect fragile surfaces from damage. And also add an unusual "raisin" to the concept of an apartment interior.
To complete the finish, a profile from any of the above materials can be applied.
Today, decorative corners on the corners of the walls are an important element of the decor. They help protect problem areas from mechanical damage. Their installation prevents damage to the road, gives the framing the interior of the finished appearance. We will tell about where such elements can be used, from which materials they are manufactured, as attached to the surface.
Corners - the most problematic place. When repairing their repair, it is difficult to make a beautifully arrange. Wallpapers pasted on them, after some time, go out and dug. When furnaces are driving in the room or during permutation, there are often damage to solid large elements, which leads to an occurrence of a sloppy appearance. Prevent all this can be prevented if you buy decorative corners for the walls and install them at the stage of finish finish. They will completely close the ends, allow you to form a smooth transition of one material to another, cover some sins of poor-quality work of the malaria.
Decorative Corners - Decor Element, Having Finished Completed Appearance Source Design-Homes.ru.
In addition to purely technical function, the angles are aesthetic load. If a white profile close the perimeter of the window opening, the window will look better. This technique is often used when, according to the design requirements, the window is not covered with curtains, but is executed using blinds. In this case, the color of the corner must coincide with the color of the wall finish. When the contrast is applied, the profile acts as a separate decor element. It immediately rushes into the eyes and becomes the original part of the interior.
Designers love to apply corners decorative and for external framing of the doorway. Especially it becomes relevant when the wall thickness is larger than the width of the door box. This difference is completely closed by good, and then the angular elements are superimposed on top of them, the color of which completely coincides with the color of the door.
Need to additional defense External angles of walls, arched openings, protrusions and niches. Installing the corners will prevent the risks of their damage from a random strike. It is relevant when the walls are simply twisted or saved by wallpaper. In addition, it is easier to make cleaning and eliminate traces of hand. If the corners are closed with a plastic profile, follow the cleanliness will be easier.
Corners can close the ends of the wall, decorated with ceramic tiles or wall panels. Often, such materials of the edges remain not stitched, so the edge looks unavoidable. Profile installation helps to completely hide such a defect.
Another scope of application is to decorate the external corners of the structures collected by plasterboard. Today, the technology of creating open shelves, racks from this material is actively used. Shakes closed by a profile look more aesthetic.
Arch, the angles of which are closed with a decorative corner
With the help of decorative corners, you can make a framing for large mirrors, cover the plinths, any joints that take the angle shape. There are profiles under the plaster, models for ceramic tileProfile products for bathtubs, furniture.
The appearance of products and their technical specifications depend on the material from which profiles are made. It determines the scope of use.
For the manufacture of such corners, aluminum, brass or steel is used. Corners made of brass and steel have a smooth well-polished surface. Aluminum profile is represented in three species. There are on sale polished samples, anodized products, or decorative coating corners.
Most often such products are used in the furniture industry, but designers love to apply them when the walls are drawn up furniture shields, MDF or chipboard sheets. In this case, a metal profile is selected, painted in the tone of the main material. Unscured metal corners are suitable for framing mirrors, paintings or posters placed under the glass.
The masters use metal corners to create a base for installing light suspended ceiling designs like "Armstrong". With the help of them you can install the lungs plastic panels. They are able to act as anti-slip overlays or as protection edge of the structure from chips and cracks.
Their main scope of use is the finish of the external or internal ends of the walls, covered by a block house, plaquene or clapboard. Move from expensive or cheap wood varieties, so they have a different price. They can additionally paint and lacquer, create on the surface with milling machine Different patterns.
Recently, designers love to use the reception that allows you to cover the wall ends, assessed by wallpaper or painted painted. This is permissible only if there are strictly straight surfaces.
Avatars.mds.yandex.net sourceChoosing this option of finishes, it is important to take into account that a wooden corner is a fragile product, with the slightest effort it can break or crack. To spoil his attractive appearance is capable of excessive moisture or long overheating. Therefore, they can not be fermented by walls and window openings in the bathroom or in the bath.
Wooden corners - fragile product
Elements made of wood with a joinery glue or PVA glue. Liquid nails are suitable for designated purposes. If the walls are not concrete, it is possible to mount wooden corners with finish nails. In this case, the gap between the edge of the profile and the head of the nail should be at least 10 diameters of the fastening element.
Such products are ideal for the frame of the corners of the wallpaper. They are very soft to the touch. If they close the corners in the nursery, the children will be less injured. Silicone profile has only one disadvantage: its transparent texture is unable to close the finishing defects from an extraneous eye. This must be taken into account when choosing and buying products of such a plan.
Silicone profile - a great tool for ensuring the safety of children Source d.allegroimg.com.
On our site you can find contacts construction companieswho. Directly to communicate with representatives, you can visiting the exhibition of houses "Low-rise country".
With the advent of polymeric materials, the possibility of decorating residential premises was noticeably expanded. There are corners with smooth surfaces, with a complex relief, artfully imitating the texture of plaster stucco. Unlike a plastic profile, the thickness of the shelf they have more. This makes it difficult to the installation process, but the appearance of the finish from this wins. Polyurethane corner creates a solidity effect. In addition, it can be additionally painted with paints applied in the finish, and there is no plastic profile.
In the manufacture of products used pressing technology. It allows you to create decorative profiles of various shapes. They are not afraid of moisture, temperature drops, serve for a long time.
Manufacturers offer universal white polyurethane corners, they are best suited for painting. There are profiles whose texture is skillfully imitates the tree. Beautifully look at the products, which have a smooth part painted, and the upper ornament is decorated for gold. Such corners are ideal for classic interiors. They are attached to a special glue composition. For these purposes, you can also use liquid nails.
Such products have a smooth smooth surface. They are made of polyvinyl chloride. Manufacturers produce collections in which products are presented by thirty shades. There are profiles that imitate the surface of the tree, metal. The scope of application is not limited to physical parameters, so the plastic profile is used quite wide. For design arches, flexible corners and arched articles are available.
Mounted plastic profile on the posted wall simply:
To glue plastic to the surface of the wallpaper, it is important to make sure that the canvas firmly "sit" on the walls of the walls that the glue under them is good dry and provided a reliable clutch. Otherwise, under the severity of the ceiling, the wallpaper is bothering and hang. It is better to glue corners, a few days after sticking wallpaper.
The video describes how to glue plastic decorative corners:
This material is also used to make a decorative profile. In the process of its creation, two strips of the same size are fastened with a duct film. It is superimposed by S. front face. Its color and drawing coincides with the color and pattern of MDF. It is possible to use such products to decorate external corners, and for the framing internal. The degree of corner is not important.
Note!The corners made of MDF undesirable to exploit in the interiors of rooms with high humidity.
In this way, the angles of walls, trimmed MDF panels Source www.meister.com.
So that the premises of the room harmonized with its filling, it is important when choosing a profile to take into account different factors. It is important to pay attention:
If the choice falls on wooden corners, designers advise to pick up the color and texture of the doors or floor finish. Then it will look organically. If you wish to save, you can buy corners of plastic under the tree.
When creating laconic interiors with a stylistry of minimalism, the choice of metal corners becomes justified. They look good in high-tec, in the loft. Shelf width need to choose such that it completely covered the end of the corner. It is necessary to pay attention to this if the walls are covered with panels, plasterboard, if the insulation and sound insulation is additionally carried out. Such edge structures are always uneven, the angle decorative well closes all defects.
Usually the angle between the slope and the wall is greater than 90 degrees. In order for the selected profile to be well to lie on it, it must be slightly bent. This can be done with metallic, and with a plastic corner. For this, experts advise the product to put on a flat surface with one edge, and then put pressure on top of hand and brush from the entire length of the corner. In the cold season, such a procedure should be done after the product of the day breaks into the room, and will take room temperature.
The video describes how the metal profile is installed on the ceramic tile:
Decorative corners help solve many tasks. They improve the aesthetics of the finishes, protect the walls of the walls and their internal angles from mechanical damage. There are products inexpensive, mounted them are very simple, so if necessary, you can experiment and try to improve the design of the finished interior.
Go to your postal service right now by clicking on the icon
and you get unique selection Soviets by exterior decoration Houses from the manufacturer with 18 year old - experience!
Important! If the letter did not come, be sure to check the "Spam" folder and move the letter to the "incoming" if it fell there.
The beauty of the facade is in the common picture, which consists of invisible at first view of the details. But there are no unimportant little things! And the trim of corners of the house occupies a special place among them. Here you need a well-thought-out system of elements that will decorate the house, combine with the main finish and at the same time strengthen the most vulnerable places of angular joints of the panels.
So that the house with the siding finish had an aesthetically completed view, the company "Alta-Profile" has released a system of finishing elements "Alta Decor". This collection includes outer angles.
The collection of facade panels "Alta-Profile" is harmoniously complement figure outdoor angles. By structure and color, they correspond to panels, be it brick or stone. Corner finishing can be performed:
"Time" various combinations of figure outdoor corners and facade panels and choose the most suitable with online programs "Alta-planner".
The "Alta Decor" collection also includes the universal trim of the corners of the facade of the house, which can be used absolutely with all the finishing materials of the "alta-profile" - horizontal, vertical and foamed siding, a block house and facade panels. In addition, such a system can be mounted with other types of finishes - for example, on the plastered facade.
The corner finishing system consists of the base and overhead finishing elements of three different sizes. Combining them between themselves, you can achieve interesting design effects. Options can be a lot, and the choice depends solely on the taste of the owner and the desired result.
The corner finishing system is roughly mounted as siding and facade panels. Since the angles are more often than the walls, are subjected to high loads, preferably mounted on a metal crate.
A flat profile of the crate is used to set the corner finishing system.
In the process of finishing the corners, the following rules must be followed:
The coal finish system "Alta Profile" comes out not only as an addition of siding and facade panels, but also with plastered facades. In this case, from the fastening base profile, you need to cut off the mounting shelf for fastening, and consolidate this profile on the wall using self-tapping screws. Next, the installation of the overhead items is performed in the same way as they are installed when finishing the house by siding or the facade panels.
Such a system will become an attractive accent, if the house is decorated with decorative plaster, and will also help strengthen the most vulnerable places of the facade.
Outdoor angles require additional strengthening. Plastering in this place is most often satisted. And the panels in the joints of the joint also need protection. The system of finishing the outer angles "Alta-Profile" helps solve this task.
The trim of corners allows you to create a bright and unique design of the facade of the house. For facade panels, you can choose curly outer angles that repeat the trim of the facade or contrast with it.
For siding I. decorative plaster "Alta Profile" has developed a universal system of finishing the corners. Due to the combination of various geometric shapes, you can make the facade of unusual.
The corner finishing system is very simple, without the use of special equipment and tools. Correct with work can even beginner.
Finishing elements are made of environmentally friendly plastic: they are durable, they do not fade into the sun, they are not afraid of moisture and temperature drops.
In addition, the materials for finishing the corners can be purchased with siding or facade panels "Alta-Profile". You do not have to spend time in search suitable materials. Our specialists as accurately calculate the required number of profiles and planks. A certified assembly brigade will set them in accordance with all the requirements of the manufacturer. You only need to choose what you want to see the facade of your home and, in particular, will be the corners gently strengthen the finish or become a bright and attractive design element.
If you firmly decided not to go around corners of the apartment When decorating it, you probably know that in order to achieve the goal can be done in several ways. Namely: to put something in them, paint or cheer photos, fill the shelves. But if you still have a question as place angle, you just look for an idea for inspiration or implementation. So you went to the address! We picked up somewhat interesting for embodiments and easy to implement the ideas of decorating the corners.
So in the angle of a small home gym You can put a whole house on a magnifying oak, then the walls should be written accordingly. Complicated? But your efforts will be paid with more than! And interestingly, and relaxing, and healthyly saving.
Fill the angle of the hallway with a special romantic content with the help of this simple, but very cute picture.
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
2. Fill the angle of furniture objects or design elements.
Builder's book
If you are interested in oriental motives, then use the case and install a carved scroll in the corner. She, of course, will not hide the corner, but at least decorate it.
Builder's book
Builder's book
But in the hallway, you can place a high table on decorative legs in the corner and put a vase, lamp or candlesticks on it. Elegant, cute and affordable.
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
3. Place in the corner of the shelves and shelves.
Builder's book
Builder's book
Builder's book
Builder's book
4. With the world on a thread or a few more interesting ideas Corner decoration
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
Builder's book
In a dark-dark house, in a dark-dark corner, this lamp looks just great! And he can give the room a special charm and chic. Maybe you should try?
Repair in the apartment acquires a finished view only if everything is correct and neatly decorated constructive elements. Manufacturers finishing materials They offer decorative elements for any types of coatings: plasters, plastic and MDF panels, wallpaper, wooden lining.
A latter role in the visual perception of the interior is played by decoration of the angles of walls in the apartment. It is them that they lose their attractive appearance faster. Having moved around the apartment, people hide the corners shoulders, scratch the tolerated objects. Quickly erased surfaces covered with wallpaper.
Protection of the angles of walls is achieved by overlays from various materials.
In addition to protective functions, the corners decor disguises minor disadvantages of finishes and inconsistencies of materials used, for example, ceramic tiles.
Important! For the design of walls decorating with panels, a decorative corner must be applied.
Metal corners for walls will help protect the surface from pet damage. Often to return the housing attractive appearance for a while, the decorative trim of the corners will help. Framing of photo stocks border ribbon Press the image view of the picture.
Corners are applied in cases:
Understanding the importance of the problem, manufacturers produce products for all types of finishing works:
Note! Docking decor from several elements beautiful decision Will you call. The standard length of decorative corners is 2700 and 3000 mm, it is enough to decorate one corner in the apartment. When you purchase, it is necessary for each angle to acquire a separate decorative element.
The design of arched corners has some features. One side of such products is less than another, thanks to this, the product becomes flexible, which allows you to stick it without cutting one of the parties. Without such an item, it is not necessary if the wall surface is made of plastic or MDF panels, drywall, lining.
Manufacturers produce corners of any colors. When choosing, you should be guided by your taste and the overall idea of \u200b\u200bthe decoration of the apartment.
In general, it should be kept in mind the rule: to protect the angle, an element is applied to one tone of darker the surface itself. In this case, the lines will be clear, the overall style of interior decoration is emphasized. If the room uses materials painted "under the tree", such as linoleum or laminate "under the boards", it is desirable to apply corners performed in the same style. Decorative stripes are glued to wallpaper.
The width of the sides of the corner is selected, taking into account the dimensions of the arched construction and the parameters of the room: the height of the ceilings and the thickness of the wall in which the discovery is made
It is necessary to comply with the proportions: what more premises, above the ceiling and the thickness of the wall, the wider the side of the corner is selected. A narrow decorative element will not emphasize the details of the interior. Conversely, a wide corner looks unnaturally in a small kitchen or hallway.
On a note. In the special literature and among builders, the side of the corner is called the shelf, it is provided for by GOST. The same name is the side of the beams and channels, to which the load is applied.
When finishing the premises, the tile necessarily appear, where its ends are visible:
You can hide the ends of the tiles, curing their paint, placing the decorative lining, or do not touch at all. Beauty by room This finish will not give.
Elements made from aluminum or plastic alloy. Coloring plastic products occurs in the manufacture. The paint is introduced into the plastics. This allows not to worry about the safety of the shade throughout the entire period of operation.
Metal parts are polished and covered with varnish. For different colors use thermal or chemical methods Staining.
One side of the corner has a perforated protrusion. It is mounted on the surface of the wall or protrusion. When laying, perforation is filled with glue for ceramic tiles, and after drying, the product is reliably connected to the wall. The opposite side is made in the form of internal protrusion. It includes a tile laid on the adjacent wall.
Attention! When buying a corner, take into account the thickness of the ceramic tile. The dimensions of the protrusions and recesses on the decor elements should coincide with the tile thickness.
In addition to decorative properties, the corner helps equalizing the walls.
For the design of joints in three planes use special linings.
For finishing of the inner corner, profiles of a special form, steel or aluminum corner are used.
Decorative corners on the corners of the walls are applied to design indoor rooms. Surfaces covered with plaster, wallpaper, are separated by decorative elements in the form of lining.
The design of the corner allows you to bend it in different directions. Due to this, such a finishing element is suitable for the design of external and internal angles (sharp and stupid), the size of which can be any: from 90 to 170 degrees.
Important! Manufacturers for the entire line of MDF panels produce corners with a similar color and texture finish. Taking into account the large variety of shades, it is desirable to simultaneously acquire MDF panels and decorative elements to them.
For registration of straight corners, corners of polyvinyl chloride are suitable. They are produced with different walls in size, which allows you to hide various gaps in width.
A separate type of decorative corners can be considered good items for plastic panels, they can be found under the name of Moldings. Moldings reliably hide from the view of irregularities allowed when circumcised panels.
Elements are attached to the surface of the surface with self-draws or nails, if the root is wooden. This serves as an additional strengthening of the design. For any type of connection, you can find the desired molding option. An essential disadvantage of such decorative elements can be considered the lack of a variety of products in color, which are mainly available on sale.
Solve the white color of the plastic panels helps textured corners.
The surface structure of the surface allows you to choose the desired option for plastic panels of any species and paintings. It is much more profitable and, we can say, "richer" look at the walls of volumetric textured finishing elements made of cast polyurethane.
The angles of walls covered with lining, as a rule, decorated with wooden elements.
Such finishing elements look harmoniously in the interior, they are not exposed to deformation when fluctuations in temperature. Fasteners are carried out by special nails with a reduced (secret) cap or with glue on liquid nails.
Natural materials are gaining great popularity in the decoration of apartments. One of them is a natural stone.
Council. Natural stone covering the entire surface of the wall, it appropriate looks in spacious buildings. To decorate small areas, stone is used strictly dosed.
The fastening of natural stone is made using building mixtures to the prepared surface.
A stone corner on the wall to stick to the wallpaper will not work. In these cases interior decoration It is made by corners of artificial material. Elements made of foamed polystyrene (foam), and they are covered with hard plastic. This makes them resistant to abrasion, scratches with random touch and blows of various objects. It looks good such elements, being glued on the wallpaper of light tones.
In cases where the walls are decorated with panels made under artificial stone, special corners are used.
There are starting elements to start finishing from any venue.
Part of the wall of the kitchen, which adjoins the sink, hobs, cutting table, necessarily needs protection. The tile, as a decorative finish, is inferior to the place of glass, mirrors, decorative panels from an organity. It is difficult to produce solid surfaces with solid surfaces, therefore, there is a need for the design of the corners, the junctions of the adjoining of different materials.
In such cases, successfully apply various elements. For example, a metal decorative corner looks profitable when designing glass or mirror mosaics. Relevant in conditions high humidity Corners of polished or painted aluminum look. Details from MDF apply here inappropriate - their service life will not last long.
Decorative angles on the walls are an important component of the interior design. Correctly chosen elements will make unique decisions in the apartment decoration, extend the service life to the next repair.
