The summer cottage is the territory where it is possible to give itself freedom to carry out numerous experiments and torturing. This is manifested not only in the interior design, but mainly in the design of the garden or the garden. The inventive and ingenious hosts are not long been guided by expensive and standard methods for the arrangement of their sites, since there is a lot of alternative solutions in fact for all areas of activity.
There are several varieties of vertical beds that allow you to optimize the use of free space. Non-standard designs - an excellent opportunity to create an interesting garden design, garden, cottage plot.
This variety of beds in most cases is used to grow decorative plants or spicy herbs.
Materials for manufacture:
Length drainage pipes Regulated in accordance with the wishes of the landlord. However, it should not be made bulky beds, because they may complicate movement on the territory.
Creating a garden
Stage 1. Create a container. To do this, we take the drainage pipe, cut down along and put on two sides with special plugs.
Stage 2. We take prepared metal holders, put them on the resulting carcasters for the beds.
Stage 3. We do in the pipe hole. They are made in those places where metal fasteners will be.
Stage 4. Delighted through the cable holes made or durable rope.
Stage 5. Fix the cable / rope with fasteners.
Step 6. Fill out the seeds obtained by clay and soil.
Stage 7. Look at the garden beds.
Stage 8. Let the pipes to the selected place. Sometimes there is a special wooden crossbar for this, or rather the design in the form of the letter "P".
Stage 9. Alternatively, you can make a special design for pipes.
Important! The gardening from the drainage tubes is not distinguished by resistant to a strong impetuous wind, so it should be selected for it, which is not blown away from four sides by the winds. Otherwise, the frame quickly collapses, with all your efforts.
The garden, made of a plastic bag, is another modification of vertical beds. It is extremely compact, functional and interesting outwardly. You can make such a bed in a couple of hours.
Materials for manufacture:
In order for the garden to turn out to be strong, it is recommended to pay special attention to the thickness of the polyethylene film, which in this case will act as "frame" design. The minimum film thickness is 0, 2 millimeters.
The process of creating a polyethylene bed
Step 1 . Cutting 2 rectangular segments of the film, the size of which corresponds to the size of the generated bed. For each side, you should leave the allowance equal to one and a half centimeters. The recommended bed diameter is twenty centimeters.
Step 2. We cross the rectangles among themselves, leaving unconceded only the top of the bag.
Step 3. Send a handle to the future bed, the strength of which will allow to withstand the weight of the bag filled with soil. It should also be considered that when watering the weight will increase.
Step 4. Fill the bag of fertilous land.
Step 5. Make horizontal cuts on a bag in twenty centimeters. They are needed in order to plant seedlings in bed.
Step 6. Space seedlings.
Step 7. Regularly water the soil and add the necessary fertilizers.
With these simple actions, you can get cheap and useful beds.
An integral element of each country area is a compost pile. This is a place where all sorts of biochemical reactions occur, providing fertilizer creation.
To create fertilizers that will satisfy all requirements for them, you should thoroughly consider several key steps: creating a container and directly correctly manufacturing the most compost. We will tell about each of them.
Stage 1. We take eight reference columns of the same length.
Stage 2. Processing the bottom of the wooden columns by motor oil or tar.
Stage 3. Drop the columns to the ground so that they are reliable and stable. If the compost box is located next to the fence, then 4 columns (that is, one side) you can attach to the fence. This will avoid the need to dig 4 yams.
Stage 4. Between each two neighboring columns you feed the crossbars in such a way that in the end it turned out three independent sections. Be sure to leave the slots that will perform the functions for ventilation holes.
Stage 5. In two sections, horizontally nail the boards up to half the pillars height. In these places it is assumed to create two small doors.
Stage 6. The remaining section will be a large door, so you should navigate only one board. It should be located at the very bottom in a horizontal position, that is, as ordinary crossbar.
Step 7. Install the covers. To do this, you can use one large one-piece board.
Stage 8. Install the workpieces prepared in advance.
Stage 9. We provide doors with handles and leaks.
Stage 10. We process wood using special impregnations.
Stage 11. Color the box in any color that matches preferences.
Many gardeners mistakenly believe that any components can be hung in a compost bunch. In reality, "ingredients" should be carefully chosen to create the right biotrement.
Among the required components of the compost heap, the following components:
All items in randomly mixed in a heap. To accelerate chemical reactions, it is recommended to cover a bunch of tarpaulos (this is especially true in the absence of a box).
A trip to the cottage with the family suggests the presence of entertainment elements on the site that will delight children. The most common way to take young dachensons are swing.
To build a swing on your own - the task is not easy, but quite perfect. Of course, you can always take a stick, tie it with a rope and hang the design on a tree, but it is difficult to call full swings. Real craftsmen prefer to build comfortable designs with a comfortable seat for seating.
Constructive components:
Indicators:
Creating a swing
Stage 1. Extend the ropes between the logs.
Stage 2. Watch the ropes each log.
Stage 3. We release the rope out.
Stage 4. Tighten the ropes on 3 nodes.
Stage 5. Fix the swing on the tree.
Important: Such swings are calculated only per person.
There are several types of garden tracks that can easily be done with their own hands.
Step 1. Remove the sidewall from the tire using a knife or saw.
Step 2. Cut the tires.
Step 3. Will withdraw the space with corrugated stripes.
Step 4. Color the paint path.
Step 5. Sprinkle a stone crumb.
This is an economical option for those who do not want to break their heads and spend time on full-fledged garden track. The tire track is usually used for gardens, as it is easily fit into the ground.
Stage 1. Drag the plugs in different colors.
Stage 2. Dump a small trench.
Stage 3. Drive support to strengthen the future track.
Stage 4. Construct formwork using boards.
Stage 5. Install the struts on the edges of the trench.
Stage 6. We put in the ridge of the trench crushed stone and carefully tamper.
Stage 7. We make a solution from sand, cement, glue and water.
Stage 8. Pour the solution into the trench.
Stage 9. Press the traffic jams in an arbitrary order. It is interesting to watch even colorful stripes.
It is the simplest and fast methods Make a garden path, not acquiring expensive materials.
The expression "in the farm will use everything" turns out to be more relevant when it comes to canices. From this plastic container, you can make a large number of indispensable tools that are actively used in the process of dacha.
For the manufacture of this tool, we need only a sharp knife and directly container.
Stage 1. Cut the bottom of the canister.
Stage 2. We note on the container the cut line for the scoop so that the knob from the canister is a handle of the future tool.
Stage 3. Cut off the extra material.
Due to these simple actions, we get a great scoop with a comfortable handle.
Materials:
Manufacture
Stage 1. Carefully my canister so that there is no smell in it.
Stage 2. Cut the vertically to the canister into two parts.
Stage 3. On the table, we make a groove using a woodworking machine.
Stage 4. We apply glue to the Faneur and insert the canister into the lower part.
Stage 5. Color the resulting shelf with a canister.
Of course, such a design will not withstand greater weight, but it is quite good to store small parts.
Materials:
Stage 1. I pierce the top of the canister.
Stage 2. We make stencils from paper.
Stage 3. Apply it to the canister, we supply the marker.
Stage 4. Cut out big holes With scissors.
Stage 5. We fold the prepared canisters into several rows, taking each row by waying the rope under the tank handle.
Stage 6. We reinstall all the rows around the perimeter for greater strength.
Stage 7. If the cabinet is planned to lean to the wall, then weiss it to the surface.
Stage 8. We put heavy items in the lower row - stones or bricks.
The result is quite a spacious and functional rack that will help get rid of the question of storing many small details.
Be destroyed and bold in the incarnation of your ideas. Good luck!
Homemade for the house is small popular among urban residents.
After all, today the market of all sorts of goods is represented by the broadest assortment, among which it is easy to choose something suitable for themselves.
However, in order not to spend the extra amounts of money for trifles, as well as to improve their own skills of skills, you can create all these items with your own hands.
Among useful homemakes for the house can be found as such:
Homemade with their own hands can be the most different. From beauty to practicality in their development there may be one step, and that proof is an interesting shelves from cruel cans from coffee. For such a craft you need:
We begin the creation of a homemade shelf from the hardening. On the back (day) of each jar, you need to make an opening that serves as a fastener to the wall.
However, do not necessarily do in every bank on the hole, but if your regiment has large sizes, there must be at least 2.
Instead of glue, you can use the drill and drill in each jar in the hole, which are bred by nuts and screws with each other, but with glue, of course, it is easier to work.
To the homemade for the home unexpectedly did not fall apart, already on the wall, it should be used very durable glue, for example, the one that is used in the repair of shoes. Can consist not only of tin cans, but also from glass.
Glass cans Can become a useful homemade for storing small things.
If there is an animal in your house, and somewhere in the storeroom or the old monitor dust, which is no longer working for a long time, either will never be used, you can quickly make a house house from it.
To do this, it is enough to simply unwind screws from the device, remove the body and separate it from the insides, including the screen. Next, we connect the details of the housing with the same screws, thoroughly wipe the monitor from dust and proceed with decorating.
As an ornament for a cat house, you can take the usual paint, which covers the entire surface of the house you created. But there is another way: take watercolor paints and show off the former monitor with patterns at its discretion.
Hanger - homemade with your own buttons
For seed hairs, we need:
You can cover the hanger with a cloth and sew buttons on the fabric, looks too beautiful enough.
.jpg)
Thread hangers
It is the hanger itself. You need dense threads that you wrap the hanger and get a wonderful homemade home made by your own hands.
To secure the threads, add glue PVA on the hanger.
All homemade homemade is very useful, as they give new life Old things and make beauty and creativity in your home.
Make your home much more comfortable crafts made from old items and things that can be returned to the second life. Some manufactured homemade for household With your own hands, you can significantly save home budget, facilitate work or make the surrounding interior more interesting. And even if difficulties arise in the process, their overcoming will cost.
Almost in any house there will always be any set of instruments necessary for the economy. But sometimes there are situations when to work in your own workshop or garage requires any device, which is no longer possible to purchase in the store or it is very expensive. In this case, the output can be found by making it yourself.
This metal heating device will become an indispensable assistant in a home workshop. Mountains can be safely used to make original items using artistic forging. It will be truly unique forged items.
For the mining, it is best to use an empty gas cylinder with a capacity of 25 liters. Its ends are cut by a grinder, and the door of the mountain and its rear will be made of the cut-off pieces. The inner part of the balloon is covered with a refractory ceramic wool, which is capable of withstanding the temperature of more than 1200 0 C. From above, it is cooked chamotte clay (fuled), withstanding temperatures up to 1500 0 C. On the bottom of the mountain after a lining, chamotte slabs or refractory bricks are stacked.
The hole is drilled on top and a small slight is inserted, which allows inserting a nozzle of a burner burner, which can create in a mountain temperature more than 1000 0 C - is quite sufficient to heat the metal to a certain temperature suitable for forging.
In the manufacture of such a lift, cash spending will be much less than buying a factory model. For its manufacture, you will have to spend only on materials, half of which may be found in the garage.
Materials required for lift assembly:
For the lifting mechanism, it is best to use a manual winch with a worm transmission with a maximum load of up to 500 kg, which is attached to one of the stracks of the crane-beam.
The design does not take up much space in the workshop, easily moves through solid coating and is quite convenient for removing the engine from the car.
The main highlight of this rack is its small amountBut at the same time it can accommodate a large number of tools, and if it is necessary to - quickly move it to any place or neighboring room. It is very convenient to use such a rack in your workshop or when conducting construction and repair work in large roomsEspecially when you need to carry out tools often.
The rack can be collected on the basis of a collapsible rack of plastic installed on a homemade platform with wheels (trolley). The platform is made clearly under the size of the rack of a metal corner with the shelves of 45x45 mm or a plywood sheet with a thickness of at least 10 mm. For movement, furniture metal wheels are used.
To the rack additionally you can make and fasten the mounts for building levelsExtension cords and other tools that can be stored in a hanging position.
There is no financial opportunity to buy, for example, any of the new furniture in the furniture salon or make an order for its manufacture. But you can always get out of this situation, making the right thing with your own hands, while making it attractive and unique, using remedies for this.
The kitchen apron is a wall surface between the worktop and mounted cabinets. Usually this part of the wall is facing tile. But for its coverage it is possible to apply many other materials, for example, gluing wine plugs on the wall.
Such an exclusive decor looks pretty great.
Before the sticker, each plug is cut along a length of two halves with a sharp stationery knife. The wall is preferably painted in black, which will emphasize the seams between the corks.
The plugs are glued onto the wall using liquid nails in a chess order either with a specific pattern, as ideally exactly it is unlikely to lay them out, and curved rows will visually look disgusting.
The plugs themselves are not afraid of moisture, but quickly dumps and are poorly laundered, so it is best to close them with a glass screen from a calene glass. True, it will have to spend a little to spend a little and order glass in a special workshop, where they will cut it on the specified size and make holes for sockets and fasteners.
Glass fixes to the wall anchor dowelsthat can be purchased almost in any construction store.
Although the apron, decorated with wine stoppers, may be expensive, but the result achieved will cost this.
The surface of the table top, as well as the wall, you can decorate traffic jams and cover with rotable glass.
Fastened on the wall folding tableiK saves some square in the apartment. In the crowded state, it can perform from the wall at a distance of no more than 10 cm and does not interfere with anyone, but in the unfolded form it can replace a full-fledged table.
Options where you can use a hinge table fixed to the wall, a lot. Here are just a few of the most basic:
Probably nothing is better than refreshing under the jet of water hot summer day, especially if he passed the work in the garden. Naturally, only the souls will solve this problem and remove fatigue accumulated in the day.
The shower can be installed on their own without attracting assistance, the main thing is to choose the place for it and decide on the type of shower cabin.
Three types of cabins stand out among summer showerwho can freely build on their own:
Installing a simple shower is made in this way:
Cabinet can be seen by boards, plywood, slate or simply cover with tarpaulo or cellophane film with folding pads.
The topic of construction or repair, probably, worries everyone. And, of course, everyone who does it wants to end it with minimal financial costs. Therefore, if you want to save, you can make some materials for construction own forces. For example, it may be a wall sip-panel or such a useful tool like vibratinglitis, the need to which often occurs in many landlord owners.
For their manufacture, you need to prepare a flat rigid platform. Putting a sheet with a thickness of a thickness of 10-12 mm rubber spatula with a thickness with a thinker with a rubber with teeth on it.
Then to glue the sheets of foam of the brand 25-30. After that, on top of the stacked foam, the adhesive mass is applied to the bottom slab, and the second sheet of OSP is stacked on top.
If simultaneously is made by several stacks stacks, work should be performed quickly until the glue is freezing. Usually in this way you can prepare for more than 4-5 panels at a time.
After the workpiece for the formed plates you need to create pressure using the press. Since at home, naturally, hydraulic press No, it can be replaced with a thick plywood sheet laid on the harvested sip-plates throughout the plane and twisted for 2-3 hours, for example, several bags with cement, sand or other cargo. You can take advantage of even a passenger car, having stopped on a plywood sheet according to a pre-made overpack.
After the glue is finally dried, the homemade panels will be ready, they can be folded into a separate stack and begin in the workpiece of new panels. Made panels should be left without cargo still, after which they can be used for their intended purpose.
To make homemade vibrating plates, you will need to cook:
From the narrow sides of the plate, retreating from the edges of 80-100 mm, make an incision with a grinder about a depth of about 5 mm. After that, get the edges in the direction of the outbreak at an angle of about 25 0 and weld them. The bend is needed so that the vibratinglitis does not immersed in the material that seal it and fluently moved along its surface.
Then across the plate at a certain distance designed to fasten the electric motor, two channels are welded with shelves down. Through in advance drilled holes In a channel, with the help of M10 bolts, an electrovibrator is attached to them.
The handle made from the pipe is attached to the vibrator through soft rubber bushings, which can be bought in the auto parts store or in a construction store in the fastener department.
Thus, you can make a lot of things useful in the farm, having spent only part of the money that would have to pay when buying a finished product. We just need to make some effort and have certain skills.
Nothing brings joy into the house as a thing created by her own hands. True, different selfiems For the house not only fill the life with bright colors, but also give the interior a uniqueness and a kind of highlight. And certainly about such a thing (let it be a little bauble) it is impossible to forget. And it is not so important that it is homemade wood for home, from paper or plasticine. Options and methods of manufacturing various things - millions, and today we will look at a few of them. So how to do interesting homemade for home?
It would seem that such a little thing is a jar of coffee. However, even from it can be made a beautiful, comfortable and useful shelf for storing economic stories. Often in such tanks are kept various souvenirs and memorable photos. Practical benefits from this homemade a little bit, but such jars look very harmonious.
1. First, in the jars, the drill or a special knife-plowing holes (in the upper and lower 3, 3, and in the walls of all others are 2 points).
2. Next jars are bonded among themselves. Nuts and short-sized nuts are used as fasteners. By the way, to obtain the desired (beautiful) result, you will need to have at least 5-6 such jars.
3. After in the tanks, a hole under the screws is made. In the bottom of the jars located in the upper part of the design, 1-2 holes for fastening the shelf to the wall are made. Finished homemade is screwed by a screwdriver or a screwdriver. For this, a dowel is driven into the wall.
Everything, now homemade for the house is introduced into the case. Be sure - a different little thing in such jars is definitely not lost. Thus, you kill two hare at once - decorate the interior and get rid of the mess in the house.
The clock on the CD is also very interesting and original option Interior decorations.
As can be seen, the design of this device is very original, and therefore it will be organically looked against the background of any interior (perhaps it will become its highlight). Made such "smart" homemade houses for the house in minutes. In more detail about all stages, we will tell you a little lower.
So, how to make homemade hours do it yourself? To begin with, you will need to prepare the appropriate materials - CD / DVD CD (the design of its front part is chosen at its discretion) and the cover-case for it (the distance between the walls should be at least 0.05 centimeters). It is very important that the latter item does not have any chips and scratches. To facilitate the work, you can purchase ready-made clock and then simply replace the standard dial.
Must be a shooter, otherwise the homemade will not work. You should also make numbers. Their total of twelve pieces should be. It can be cardboard, paper, or plastic circles. Their thickness should not exceed two millimeters. Rhinestones can be used as decorations. You also need to prepare about 30-40 centimeters of wire, a piece of skin or tissue and superchalter type "moment". The main all this design will be the CD. We will redo it in the first place.
First you need to place the disk on twelve equal parts and glue the numbers to the marked points. At the same time, the sectors should not go beyond the outer diameter of the device. How are homemakes are made for home? After the sectors, proceed to the hour yourself - remove the arrows and place them exactly in the center of our disk. By the way, in front of their fastening, you can stick some interesting photo on the disk, which will make the design of the clock even more original.
To increase the size of the arrows, use thin metal strips. To achieve the desired result, it is enough to apply glue on them and gently arrange the item exactly along the entire surface of the filling elements. The same shooter mechanism is attached to back side disk.
So, the base of the clock is practically ready. The next step is to do the holes in the device along the contour of the shooter. The field of this disk is installed in the case. The mechanism itself is displayed out through the hole and closes tightly. Now, with the help of wire, the stop is made, which is glued to the back cover. So that it is more durable, rushing a piece of fabric or skin on top of it. It will make the emphasis not only strong, but also beautiful, since the extra part of the wire no longer gaps on the clock as before. All, homemade hours from the CD successfully manufactured. It remains only to insert a battery of the AA type and set the time. By the way, the battery can also be made with your own hands.
As we know, this fruit contains a lot of acid, respectively, with the correct actions, the lemon can be turned into a real mini-battery.
Of course, the charge from such a "battery" is not enough to work household appliancesHowever, for the functioning or charging of the mobile phone of this current is quite enough.
In the course of the work you will need such tools like a knife, soldering iron, drill, iron pin, as well as several pieces copper wire In isolation. Among other subjects, it should be noted the need for a single glass or a glass, a pair of wooden sticks and the same amount stationery buttons. And, of course, the main source of energy we will have lemon. An orange can also be applied, however, the acids in it are much smaller, so the charge will be minimal.
First, lemon is cut in half. It is necessary so that it gives more acid necessary for lemon is fixed in the glass so that it does not ride on the table. Next in its pulp, copper and iron pins are inserted throughout the perimeter at a distance of 0.5-1 centimeter. "The minus" we will have an iron, but "plus" -med.
All pinways are attached to the wires of the wire. They will perform the function of the power supply connector. All items are connected sequentially.
At the final stage in battery compartment Sticks are inserted. It is important here to observe the polarity. Contacts are pressed against the contact group. The container remains open throughout the device charge process.
So, we found out how to make useful homemade for home with your own hands. Successes in your endeavors!
