The stand for the soldering iron is an indispensable attribute of the soldering installation. It can be purchased at any construction store or on the market. However, its cost is large enough. In order to save own funds, a stand is manufactured for except financial issues, its functionality is considered. That is, it can be used for various needs in the farm or in the manufacturing workshop. Many products have enough options. All of them are distinguished by the complexity of the design and the amount of time spent.
As mentioned earlier, the stand for the soldering iron, with his own hands made, - a convenient device that performs many functions. First of all, it is a protective surface that prevents damage to property.
Before working with a soldering installation, it must be warm up. In this case, the metal body heats up to high temperatures.
The quality item is necessary for those people who perform many works with soldering. For the manufacture of such a device, like a soldering iron stand, no special skills and skills are required. The process uses simple and affordable materials and tools. The finished device is easy to handle. The self-made stand for the soldering iron should consist of separate elements. First of all, special containers for rosin, flux and department for mixing them are provided. Some models are equipped with a box where small details are stored. Soldering stand is suitable for any device, regardless of its power and heating degree. In the manufacture of the design, the location of these containers should be taken into account. Everything should be so that the master it is convenient to solder.
Buy finished stands unprofitable because they have high cost and small dimensionswhich are not suitable for all types of devices. Therefore, many users are asked as a question: "How to make a stand for the soldering iron with your own hands?".
Before the start of manufacture, you need to prepare materials. To do this, purchase the following components:
When all these details are purchased, you can start making a stand.
So, there are several holes in the plate. They will consolidate the tanks for rosin and alcohol. Installation of cans is performed easily. Capacities should be easily inserted into the design, as well as tightly lay down to each other. After these procedures, it is necessary to make support. It is made by bending the base.
If necessary, each person can make special racks that raise the design to a certain distance. This is done for convenience in the process. Preparatory work End on the processing of a duraluminum sheet with a file with a file or emery paper. Corners should not have acute ends.
So, proceed to the assembly of the coach for the soldering iron. Prepared support must be consolidated to a wooden bruster.
This can be done with screws. Next, the addition of harvested small containers is performed. They are attached to the base with a special adhesive or epoxy resin. Many masters are also installed between the racks a small container. It can store small details that will be needed in the process.
Stand for the soldering iron from the wire was gained great popularity from many masters and lovers. It can be made from the usual canning can. Simple details are applied during the installation process:
First you need to make a spring. The first thing to do is to buy a wire in the store. Some people remove it from other indoor devices. It should have a sufficiently large thickness so that the soldering iron warmed up to large temperatures does not destroy it. In addition, only high strength material will go into operation. The finished product should spring.
Cut off the required wire length and thoroughly align. To create a spring, a large diameter pencil is used. Holding the wire, carefully screw it on a pencil. As a result, a dense spiral should be. At its end, a special attachment in the form of an ear is made. For these purposes, pliers are used.
The next step is to prepare canning can. In its day, the hole of small sizes is drilled.
This can be done with a nail or drill. Next is going to the soldering iron stand. The prepared spring is inserted into the jar and with the help of a bolt and nuts fasten the design. To ensure a more durable mount, the washers are used. This method is quite simple. Stand for the soldering iron can make every person. It does not require much time for its manufacture, as well as special tools.
More and more people prefer to use exactly this species Stands. Its essence is that it is equipped with a special device that independently adjusts the degree of heating of the soldering iron. Therefore, the device does not overheat and does not fail. The stand is different from other species in that it is necessary to connect to the power supply. For the manufacture of an option with a power regulator, you must take such items:
After all the necessary details were purchased, proceed directly to the assembly of the stand.
To begin with, the size of the installation is selected. Based on these information from the plywood sheet, the base is cut. Next, the transformer and other details will be attached to it.
Manufacture this option Does not take a lot of time, and also does not require large financial investments. As a base, a wooden bar is served on which the fuse sponges are attached. They can be different sizes. It all depends on the personal preferences of the masters.
First of all, the main advantage is mobility. Homemade stands use people who are often engaged in soldering, working within several workshops. Not always at hand there is such a design. However, it is easy to make it. In addition, it is not necessary to separately wear rosin and tin in different tanks, since now they are stored in special jars on the stand. therefore homemade installations We are successful not only among lovers, but also from professionals.
It happens that it urgently needs to use the soldering iron, and there are no supports for it.
In this case, there is no time to look for the necessary details, and run on shopping. Therefore, it is better to make a simple, but also reliable design. There are many options, but there is the fastest. Stand can be made in a few minutes. As a base will be the usual wooden barber, and stands are screws or nails. They are driven into the cross cross-cross. Thus, the stand is formed, which solder the soldering iron and keeps firmly.
When soldering elements, a stand under the device must be present. This auxiliary equipment It is expensive, so it's better to make it yourself. Such a process will not take much time, forces, as well as save funds.
The main tool of the home radio amateur is a soldering iron. Unlike other devices, it is impossible to just put on the table (workbench) during operation. Why? Right! He is hot. Therefore, you will need a special stand.
There is a lot of diverse tools on sale, from a simple holder to a whole complex called the soldering station.
In most cases, the soldering iron is needed to perform urgent repair work. If you are not a professional "self-relocine" - the tool is usually dust in the box on the balcony, appearing on the world once or twice a year. In such cases, many use the first item as a stand.
However, if you make a very little effort, the stand for the soldering iron, made with your own hands will look no worse factory. Especially if you regularly seize electrical stakes.
In old radio magazines, you can find drawings, how to make a stand with an economical load switch.
The design is simple, but convenient and efficient. If you do not want trouble with contacts - we make a simple functional stand. Again from the experience of Soviet radio amateurs.
Stand for the soldering iron with your own hands is necessary when working with a tool. Factory devices are mainly not practical and do not have additional functions that make up work significantly.
Using something as a stand usually leads to the burnt surface of the table, spoiled by tin and rosin clothes, hands burns.
Work on the "knee" is rather not comfortable and takes a lot of time. The costs of time and material investments in the manufacture of the stand are insignificant, the convenience and speed of work compensate all the efforts to manufacture the device.
The basic requirements for substitutions defined by exploitation:
The size of the product will depend on the power and sizes of the soldering iron.
Figure 1. Standout scheme to a soldier for automatic temperature adjustment.
The most common option manufactured within an hour. For the bottom, you can use a segment wooden board Thickness of at least 15 mm. The width and length are determined by the soldering iron model. The tree of wood does not play a big role. It is desirable that the material is dry.
Surfaces are desirable to overtake or handle the sandpaper.
Then from the steel wire with a diameter of 3 - 4 mm, two racks should be taken. Typically use welding electrodes, freeing them from the coating and processing the emery skirt.
In the form of a rack look like the letter "M". The front of them should be higher, the average bending is somewhat already, but the soldering iron must lie freely, without fixing. The rear rack is slightly lower, the bending is wider. The lower ends of the racks must be sharpened on the sandpaper or file. Then both racks to score into the board, respectively, the sizes of the soldering iron. The sting of the soldering iron should be in the air, the heating element should be located on the front rack. If a segment from a solid wood is used for the base, it is desirable to drill two holes under the rack of a depth of 4-6 mm and then score them.
A flux and solder bath can be made from an old MBM type capacitor required size. He does not need to cut down the bottom at an altitude of 5-8 mm, and pull it. The resulting bath must be rinsed with solvent or alcohol, degreased it. After drying, the bath must be fixed on the ground, approximately in the middle between the racks. For fastening, you can use a pair of nails or small screws. In the absence of a capacitor, you can use a suitable cover from a canning can or any other tin bath. The thickness of the tin should be small, otherwise when working with a soldering iron of small power to melt the solder will be difficult.
Stand is ready to use.
Back to the category
The main lack of soldiers is their long-term initial heating. When working with the schemes, the soldering is needed periodically, and the soldering iron must be kept on, otherwise the work process is significantly lengthened.
In addition, the soldering iron overheats, the solder and sting are oxidized. Simple schemeMounted on a soldering iron stand will help maintain a tool at a lower temperature, quickly warmer when used.
For the manufacture you will need:
The base for the stand must be a few large sizes than in the previous version. A socket and microswitch is desirable to arrange side from the site of the soldering iron.
Figure 2. Heating regulator circuit.
In the case of the socket, you need to install a diode, connecting it to one of the sockets of the rosette, the polarity of the connection is not important. The power cord is connected by one wire to the second socket of the socket, the second to the free entry of the diode. The microswitch is connected by normally closed contacts parallel to the diode.
All connections and diode are preferably isolate any affordable way. The microswitch must be fixed on the base and set the movable bracket to switch it. The soldering iron lying on the stand must press the bracket lever with its weight. The bracket will switch the microswitch, the contacts will open. The soldering iron will be connected to the voltage of 110 V. The power consumed from the network will fall at twice, the temperature will fall accordingly.
When raising the soldering iron, the bracket will rise, the contacts will be closed, for a few seconds, the soldering iron warms up to the required temperature.
To monitor the presence of voltage into the socket or on the basis, you need to install the voltage indicator (any available).
Usually, when using such a stand, they often forget to turn off the soldering iron at the end of work.
Back to the category
This scheme allows you to slightly stabilize the work of the soldering iron when the voltage drops and jumps in the network. Unlike the variant described above, instead of one diode, you need to install a diode bridge with a smoothing electrolytic capacitor at the output. For manufacture, it is necessary:
To control, you will need two pairs of normally closed contacts. You can use two microswitches or contacts from the relay open type. Contacts must be closed with a lid of dielectric material.
One pair of contacts (Fig. 1) turns off and connects one of the diodes of the bridge, the second is a condenser. In the working position, nutrition on the soldering iron enters the bridge and smoothes the capacitor, in non-working - through one of the bridge diodes.
The design and dimensions of such a stand will depend on the available elements. The main elements are similar to the previous versions. Make a movable bracket to switch contacts from the relay used, deleting the core and winding.
Small prehistory. I have long wanted to do Normal stand for soldering iron but did not know where to start. I recently got into my hands the lid (I don't remember exactly), which lied for a long time in the box.
She snapped me on the idea of \u200b\u200bconstruction.
For the manufacture of the stand I used:
- "Unknown" cover (stand);
- Phaneur;
- Wooden Staff;
- self-tapping screw;
- nails;
For a start, I removed everything too much from the lid.
On the sides were left »Tags," which will play the role of attachment.
Then it was drinking from plywood 3 planks. Since the bottom cover is not even, for convenient mounting to the base, the substrate was revealed. 
Of the three dug dusts:
In the "tongues" I drilled holes. After them, screwed two identical planks to the screws.
In order for jars with fluxes do not fail, a small planker was cut out of the plywood, two small staps were cut to the ski.
I nailed this smell on the carnations to the ground, putting the podlocks under it.
The septum into the lid was cut out of the tin. From tin, which was cut off from the lid, I bent a stand on a soldering iron. The partition was screwed to the screw to the base through the holes in the lid. The stand screwed to the plank without holes.
Under the apartment on which the soldering iron will fall, I drank 2 strokes and nailed them on the carnations.
In a part of the lid with the partition, I placed a sponge. Cellulosic sponge for washing dishes. Sponges that sell specially for cleaning the soldier sting, no difference from cellulose sponges for washing dishes, only in size and price. Sponges for dishes are much larger, and cheaper at the price. This sponge was bought in a household store for 30 rubles.
From the sponge was removed the lower part. I also cut it in the size of the lid.
For the manufacture of the device you need to use materials that are not strongly heated, it is practically no heat. Good alternative option - This is equipped with a homemade stand with special legs. The minimum design functionality is:
In addition, you can also add a number of additional functions to which:
How is the stand for the soldering iron with their own hands? Below we give a few most simple waysFrom which you can choose the most suitable for you.
This design allows you to work as comfortably with a glass, not spending effort to keep the soldering iron and two parts connected simultaneously. It is quite deservedly called the "third hand." For its manufacture, the following techniques will be required and accessories:
First of all, you need to prepare the basis for the future stand. For this, three niches are freserving in it. The first two will be 
Used to install cups from candles, and the third is for a cleaning cloth that removes the solder from the soldering iron. After that, all work is performed in such a sequence:
Such a stand does not require significant financial investments, but makes it easier to work with the soldering iron.
In Chinese online stores, you can order ready-made kites for home soldered stationswhich quickly collected in the system adjustment and tool power monitoring. You can also make a regulator with your own hands using such components as:
How to make a power regulator from all this? The answer to this question you will find in the scheme below.
The board can be made independently. It drills holes for parts and conductive tracks are performed.
If you have a minimum experience in working with printed posts, the manufacture of the regulator will not be difficult. Install it can be directly on the soldering iron stand. If the device is planned to use the power to the power above 100 W, it will take use an aluminum radiator that will divert the excess heat from the simistor.
A soldering iron with a power regulator will allow working with small parts and LEDs, will provide the ability to adjust the device under your needs. In addition, it will help reduce the load on the device and extend its life.
The stand in this case itself can be made of a rectangular screaming of a board or chipboard. A steel plate is screwed to it with self-tapping screws, an inverted letter "P" with cutouts to install the soldering iron. Additionally, it is possible to install tanks for rosin and solder (all the same cups from decorative candles).
