There was an opinion that the laminated floor is pretty simple. We will not dispute it, but in the process of work, depending on specific circumstances, certain difficulties may arise. The most common problem occurs when it is necessary to connect one coating with another. Such a situation occurs even when the entire apartment is caught up with the same laminated material. Anyway, you have to meet with the question of how to keep the laminate between the rooms, use the thresholds or to do without it. It all depends not only on the design decision, but also on the technical preparedness and expense of the styling specialist.
The junction between laminate and laminate is performed under the following circumstances:
Using the combination of laminate, you can perform all sorts design solutions. For example, it is possible to visually increase the size of the room. To do this, docking the same coating indoors without installing thresholds.
Combination different materials It is possible to create a unique interior. You can roll the laminated panels of different shades or textures in the space of one room. Board connection is made in accordance with the general design. 
Note: Currently, the combination of two floor materials during the design of the room becomes an increasingly used artistic reception, as a result of which the interior design of the room acquires a special charm and uniqueness.
Recall that to lay the laminated panels, the base is required to prepare well, align and clean from all pollution. For bumps of two outdoor materials, this condition is also necessarily.
For docking laminate with laminate, it is necessary to foresee that the panels can have a different thickness, it is 6 - 12 mm. The most good way is to acquire laminated boards, the substrate is the same thickness to avoid the smallest difference in the height of the surfaces. It is very good if the materials of one manufacturer will have to be allowed so that they have the same type of lock connections, the same strength class, and therefore the service life.
How to dock a laminate with a laminate, with a booine or without a neck, and which profile apply for the junction of the laminate?
There are several options to docile laminate with laminate. Consider the most common and less complex.
Most often, the connection of laminated surfaces occurs when switching from one room to another, i.e. in the doorway. Here you definitely leave the technological gap. With its absence, it is likely that the formation of deformation, swelling of the floor surface. Left gap must somehow arrange. How to close the jokes of the laminate?
Laminate junction in the doorway To our joy, all these questions have long been thought out, the answers for them have long existed, our task is to take ready solutions And correctly apply them. Coating manufacturers produce a variety of components. This includes: substrates, plinth, connecting plates for laminate. The planks for the connection are called a threshold, molding, a profile for the connection. They differ in shape, and are made from various materials.
According to the forms, the docking strips for the laminate can be divided in this way:
Considered products carry a decorative load, but not only. When installing the laminated floor, the presence of a technological gap, which the connecting profiles are made hidden, protect against damage and allow us to have aesthetic appearance.
The connecting profiles are made from various materials.
There are several ways to design a joint line:
With all its advantages:
The case in their serious shortcomings:
Aluminum moldings can be mounted by open-ended by applying dowels and screws. On the aluminum plank, ready-made holes for self-tapping screws, which are sold together with a metal spawning.
Aluminum threshold, open mount The decorative method of fastening - more attractive looks, attachments are not visible, it is hidden under a decorative nozzle.
The mounting profile is connected to the base with self-draws. The decorative nozzle is stacked on top, pressed until it clicks. It closes the traces of fastening, and the joke looks pretty.
How to fix a universal profile:
Quite often occurs such a combination of materials. Both coatings have high quality, but it is necessary to make them right and aesthetically arrange their joint. From this depends the strength of the floor covering and interior of the room.
Consider the case of the connection: the thickness of the linoleum is much smaller than the thickness of the laminated panels with the substrate. There are two connecting paths in this case:
Conclusion
Now you know how to connect a laminate in the junction with a linoleum, how to connect the junctions of a laminate with a laminate between the rooms, it remains to be left to reality. Large problems with dusting coatings will not arise if everything is done according to the instructions. If the connection line of the complex shape or too long, it is better to entrust the combination of surface connection to those skilled in the art.
From such small but important momentsAs the design of coatings, the level of repair and the overall interior of the repaired premises depends.
How beautiful to docile linoleum with laminate
The floor covered with linoleum is quite popular among buyers, as this material is easy to clean, and it is possible to use it for a long time. Its price is also quite democratic compared with other options for creating a surface. But nevertheless, this flooring has some problems during operation: the linoleum cannons are disconnected, which leads to their bloating, which is why it is quite rational to combine several types of materials, such as linoleum and laminate. But how to connect laminate and linoleum, while not damaged none or another material outdoor coating?
It is necessary to add that the floor covering is practical, economical and easy to use, which caused the growth of its popularity among buyers. Therefore, it is important to know how to docile laminate and linoleum in such a way that when connecting these surfaces, it is a guarantee that you can use a sufficient period of time.
One of the main conditions of successful dusting is the understanding of how these materials are harmonized between themselves and whether to combine them.
In addition to accounting for the combination of flooring among themselves, when they are laying on the floor, it is always necessary to remember: if the thickness difference is quite large, the laying of the floors will not be successful. When docking surfaces, the same problem may occur - they often have different thickness.
But nevertheless, it is now possible to solve the problem without docking when laying a different kind of surfaces - for this you can use staks for joints and compounds of floor coatings.
We make a joint
How to dock laminate and linoleum, what types of slats can I use for this? The empty staps for connecting the joints are often used in the threshold zone, since they can easily hide the end outdoor materialAnd also additionally fix. If the side side is quite thick, you can apply a decorative angle.
What role are the connecting and empty slats play in the coating connection process, from which they are produced? The connecting sheets not only serve as retainers in the joints zone of floor surfaces - they can also perform the function of designer decoration. The options for docking materials are quite a lot - they are made in the most different styles From the imitation of gold to the tree, the circle of choice is quite wide.
Material options for manufacturing
They are made of aluminum, plastic (laminated). Anodized from aluminum more racks to use at the entrance than laminated.
Plastic are not highly popular among buyers due to the fact that they are amenable to erasure, have a lower level of strength compared to aluminum.
The most stable is the brass joints. Of course, the price is somewhat higher than aluminum or plastic. It is not always possible to apply this species, as they are not decorated, they remain the same species as the brass itself, the color and the form do not change, but you need to remember that they fill.
How can I fix the docking strip?
To do this, take screws that should be screwed to the floor. The mount can be made in a secret way without using screws - this is possible if there is a special groove on the back of the strip, in which the screw can be fixed on the opposite side.
In addition to fixing with screws, you can consider the fastener using the glue if your gender is made of tiles.
Thus, the combination of floor coverings can be quite harmonious if you select similar styles and the corresponding design. Surface connection will not be difficult if you use connecting strips that there are quite large number of options.
The word "repair" sometimes causes shock from many people. Indeed, in the process of converting housing there are many problems.
For example, one room may have several assignments, and then you have to combine different types Coatings, in particular, this is a linoleum and laminate.
The complexity is that the thickness of these two materials is different - linoleum is thinner 3-5 times. If there is a combination situation, this question can be solved, knowing how to dock linoleum.
It is necessary to do it very carefully, taking into account the differences on the floor. Adhering to a certain technology, you will definitely get the desired result.
The linoleum is the most common, used as an outdoor coating. It is not strange, because it has a number of benefits:
But he has and cons - linoleum sheets can be deformed, from air from them. This leads to the formation of waves, which looks not quite aesthetic.
Therefore, it is best to combine several outdoor materials.
An excellent option for such a combination will be a combination of two materials, we will now understand how to stick linoleum and.
Laminate recently scored many fans among buyers and specialists, because the price of some of his species is not particularly higher than on linoleum.
At the same time, the material is quite practical in operation and easy to install.
Therefore, the joke should be made to produce qualitatively that this combination would light up for a long time and even pleased the owners' eye.
This type of joints looks better and neat multi-level. Such an effect can be achieved using special moldings and lining.
First of all, you need to align the difference in levels. This is done with a dense material, which is recommended to sash under linoleum.
As a rule, for this purpose is used (multilayer). Having made the perfectly smooth floor of one level, on the junction, as a rule, impose a bar or threshold.
It protects the edges of the material from damage, and improves appearance. Now the docking of laminate and linoleum, with the help of mounting foam, as well as different sealants.
They will be able to make seam any width. But to work with these materials you need to have a special skill, because without experience you can make a lot of mistakes.
Most often when docking various outdoor, you have to deal with different heights. Such a task will be helped to solve the thresholds and connecting strips, which smoothly and elegantly hide the transition from one material to another.
This method will help to hide the joint with the floor level difference to 1.5 cm. In addition, such a threshold will reliably fix the linoleum and laminate, and the transition will be not only even, but also neat.
Material for the threshold can be plastic or aluminum, and some cases and. The most ideal and durable version will be a metal threshold.
Unfortunately, he will not always be able to fit into the overall interior. Often there are direct thresholds, but you can make curved. They are attached with the help of self-tapping screws, a height of one level with an outdoor coating.
There are many other devices for closing the joints. They are made of various materials. Most often it is planks and moldings from durable, wood or aluminum.
Very rarely apply such material as bronze. Turning to the construction store, any manager will tell you and help you decide on the choice of this issue.
Fasteners are divided into such types:
Hidden way fastening technical features Very similar to the open way. The difference lies in the structure of the plank. It consists of two parts - the lower is no different from the first option, and the surface of the smooth plate, which simply snaps up, giving the aesthetics of the appearance.
There is an embodiment of the tile and linoleum connection without applying slats and thresholds, the method is more complicated by the usual, but very spectacular. In this embodiment, it is necessary to put these two material on the same level, but so that the linoleum is slightly overwhelmed on the tile.
It is necessary to prepare the following tools: a sharp knife, a spatula, to apply glue, directly the glue for the glue of linoleum, special adhesive for the joint, which has a needle nozzle, roller and greasy tape.
First of all, it is worth gluing the material in the joint area. Linoleum sheets should be turned out at the junction, 20 centimeters are quite enough. Then the spatula needs to gently apply glue and press the material with a roller.
After performing all these actions, you need to glue pieces:
Scotch is needed to protect the material from the hit of glue, which can spoil it.
The video material shows cold welding of linoleum:
This method is more often used for commercial linoleum. In this case, the seam will stand out, but it will also become durable and neat.
Professional repairmen most often use such, since they have everything necessary equipment. The welding of the seam is performed by a special additive cord that is made of plasticized PVC.
For this process, the temperature reaches 300 -400 degrees. In this procedure, there is a softening not only the lace, but also a linoleum, which is then processed using a presser roller.
As a result, the seam is neatly cut. At the beginning, you need to make V-shaped holes that are previously cleaned. To perform such a seam, the linoleum should be qualitatively glued.
In conclusion I would like to note that there are many hide outdoor seam between coatings. Previously, Linoleum was simply nailed to the floor with nails.
Modern technologies that do not stand still offer a lot of lighter and aesthetic options. To solve this task, it is necessary to approach responsibly and explore all the options so that you please the result.
Compatibility and combination of flooring can very harmoniously fit into your interior, connecting elements that are now very difficult to achieve this result.
To choose optimal option Docking, it is worth considering the color range of outdoor materials, as well as carpets that will spread after. Only harmoniously selected color solution Create comfort and beauty in your housing or office.
One of the most common materials used for floors is linoleum. It is easily fit, easy to care, does not cause any problems to the owner during operation, the period of which is worth noting, very long. However, that the coating look harmoniously and served all the stated time, it is important to sit correctly. And during the laying of linoleum there is such an aspect as right docking The edges of two separate canvases. How to dock linoleum among yourself? Get an answer and get acquainted with all possible methods You can in this article.
Docking linoleum - the process is quite simple, although it is performed strictly according to a certain regulation. But the connection of two separate canvases will be directly dependent on what method the material will be laid and what it is.
Linoleum dock - Features
Severe two main types of linoleum - commercial and household. The main difference between them is the thickness of the material. Commercial linoleum is much thicker and stronger than the usual household. Because of this, it is more difficult to combine it, but it has high strength and durability. So before laying the material will have to make a choice, which view will be used. Also there is semi-commercial linoleum.
Tip! Buy linoleum thinner 3 mm even for laying in the apartment is not recommended. It is very quickly wearing.
Despite the seeming monolithium, the linoleum consists of several layers. The top layer is facial, which is made of PVC. It is from its thickness and will depend on the strength and wear resistance of the material as a whole. Thus, just and can be allocated:
In addition to the facial, Linoleum has other layers:
From above, linoleum can be covered with moisture-resistant varnish, which will not only improve the appearance of the coating, but will provide additional defense decorative layer from external influences.
It is also necessary to decide what color, with what pattern the material will be used. Coloring selection is now very large - linoleum can be monophonic, and can have any ornament or look like a stone or imitate the boarding floor. There are drawings resembling carpet or tile. Material must approach color gamma To the overall style of the interior.
Attention! If the linoleum has a complex geometric pattern, then in the joints of the joints, it must coincide. Therefore, it is necessary to buy material with a reserve necessary for docking the canvas. Accordingly, the cost of acquiring linoleum will be increased.
Linoleum laying methods with a subsequent docking there are two - laying of bribes of therapy or butt into the joint. The first laying option has some drawbacks:
That is why this method of laying a linoleum is not recommended to use and better drain the canvas of the joint into the joint. The most important thing is after the material flooring to connect two canvas so that there are no moisture or garbage for them. Fortunately, there are several convenient ways of docking. We will get acquainted with them and look at what more convenient to use when installing linoleum.
linoleum Tarkett
The docking of individual linoleum canvases is made to achieve the following purposes:
4 basic methods of linoleum docking are distinguished. They can be carried out both with adhesives, and through additional elements. Types of docking seams:
We will get acquainted with all the methods of docking the material closer.
This method is a joint processing between two cuts with special glue for linoleum. The composition, acting on the material, is able to dissolve it, penetrating deep into the structure of the linoleum, and the frozen, reliably connects two separate canvases. Glue is pretty toxic and working with it carefully, observing safety and ventilating the room. Otherwise, it can be easily poisoned by pairs of substances contained in the composition of the adhesive.
The method is easy to perform at home, easily glues and household linoleum, and commercial. But only comes in the event if the gap between the slices of the material is small. Also, the methodology does not require the acquisition of some special equipment. And the seams between two cuts will be completely invisible for the naked eye.
It is important to remember that the welding of this type is not used for a material having a warming felt layer on the involving side. It is also not used for thick multilayer types of linoleum.
Adhesives belonging to the discharge of cold welding, there are three types. Each of them is suitable for processing a certain category of seams.
Table. Types of adhesives for docking linoleum.
| Name | Characteristic |
|---|---|
| The glue is used to connect the cloths of a new material, just brought from the store. Suitable for gluing and household, and commercial linoleum. The glue is very liquid, therefore it is recommended to process them only small gaps and, it is desirable to work only with a dense material. To work with glue, you must purchase a greasy tape and use gloves. The deadlines for drying the adhesive composition are about 30-40 minutes, after which it is possible to walk without fears. |
| The glue composition is suitable for processing material with a thickness of up to 4 mm. It is often used for docking or repairing linoleum, used in use. Allows you to stick the canvas lying with big gaps. This glue is sufficiently thick and does not require the use of painting tape when working with it. |
| Such adhesive is used to connect Linoleum from PVC, which has a polyester base. Suitable for docking and new, and used material. Often used for gluing linoleum to chernovoy semiBut rather expensive and is usually purchased to glue the web used for commercial purposes. |
cold welding for linoleum
Important! When working with any type of glue, it is important to ensure that the composition does not get on facial material. Otherwise, the canvas will be damaged. Delete drops of glue by erasure is not recommended - it is better to wait for it drying and cut off the drop with a sharp knife.
Step 1. Two linoleum canvases are stacked by a mustache about 5-6 cm. It is necessary to create a high-quality cut and good docking.
Step 2. A section of two linoleum canvases is made in the middle of the adolescence. To do this, the markup is applied using the ruler, the smooth line is stuck.
Step 3. The cut is most convenient to produce using a metal line. It is well pressed to the material along the previously applied markup. Next, the sharp knife is cut. Both layers of material are cut at once.
Step 4. The resulting linoleum trimming is removed as a result of the previous procedure. It turned out a neat junction, which is even now invisible to the eye.
Step 5. The linoleum junction is punctured by the usual painting scotch.
Step 6. At the place of the docking of the canvas is cut with greasy tape, also using a knife.
Step 7. A special cap equipped with a needle is screwed on a tube with cold welding glue.
Step 9. After applying glue, it will be waited for about 15 minutes so that the glue grab.
Step 10. The malarious tape is neatly removed. Full drying of glue lasts about 40 minutes, then you can move around the floor.
Hot welding is the most complex type of linoleum docking, which is the most reliable. Unfortunately, he involves the use of a certain type of equipment and is therefore rarely used in everyday life - mostly only for commercial use. Yes, and for household thin linoleum, it is also not suitable, because it is capable of overly melted the coating.
On a note! The temperature of the equipment and materials during operation on the hot welding method reaches about 450 degrees.
Linoleum in the case of hot welding use usually first glued to a rough base. Only after drying the glue produced work on welding joints of the coating. The linoleum canvas during the flooring are not stacked, but as close as possible are suitable among themselves.
For work, the following tools will be required:
A special cord is used as a docking material made of PVC and with a thickness of about 4 mm. You can buy it in the construction store Coven 100 m and absolutely any color. Under the action of temperature, the cord melts, thereby filling the jack between the canvas. After cooling, the cord acquires exactly the same characteristics as the linoleum itself.
Step 1. With a special cutter at the place of the joint, the groove is created. That is, a small width of a piece of canvas is simply cut. But at the same time the material does not cut up to a rough base. Garbage, if it was formed, removed from the groove.
Hot welding cord is inserted
Step 3. The nose of the device is attached to the beginning of the groove. After that, the device is conducted along it. The cord melts and fills the groove.
Step 4. The remnants of the material formed after melting the cord are removed by a knife or special device (in the photo). Removal is done until the material has yet frozen.
Important! The cut of the cord should be taken such a length to handle at once about half the length of the joint.
Linoleum can be shown in other ways. For this, double-sided tape or special thresholds or profile can be used.
- The easiest material for linoleum docking. The method with its use does not imply large temporary or financial costsBut a qualitatively glue two web material will not work. In order to glue the linoleum in this way, the tape is simply glued to the rough base, and then the linoleum can be glued on top of it.
Linoleum dock with help Metal thresholds Also simple, but there are more work here than with scotch. Also, the thresholds are not always able to choose the color correctly and they look not so aesthetic, as the seams embedded using welding.
Complete with the boobs are usually sold and fasteners - screws, dowels. It is necessary to simply screw the threshold at the place of the joint of two pieces of linoleum to the floor. The difficulty lies in the fact that concrete base You will have to first drill to get holes for dowels.
Metal spores for docking linoleum
On a note! If the linoleum has a curly joint (and this also happens), you can use a flexible profile or still to stay on the cold welding method.
If you dock two pieces of linoleum is not so difficult, then connect the edge of the linoleum with other materials is already harder. To dock linoleum and tile or laminate, you will have to solve several problems:
How to make a joke
If necessary, such a dock the best way - This is the use of the clad, if the materials are on the same level. If you plan to leave the steps, you can use the angular profile.
The correct docking of linoleum is the key to the fact that under the coating will always be pure and dry, and externally, the material will look very aesthetic. And, as we can see, there are no special problems with the performance of work - it's hard to make it yourself.
