Some premises are not intended for laying parquet Board In connection with their appointment. For example, this is a bathroom, a kitchen, a place near the fireplace or oil in the bath. How to make two material to be combined and looked in the winning light. This will help the docking of the parquet board and tiles by special materials. Made on conscience Combination is difficult to distinguish from the whole web - this is impressed.
Bug between parquet and tiles.
What are the difficulties of combination? It would seem that two material perfectly lying on the floor junction simply do not require. However, only the tile is, and the parquet is a material that changes with the temperature differences, humidity, load and other things, that is, whimsical. There will be no problems with him if its laying will occur on a limited area without transitions to other surfaces.
The grooves and lock connections are securely clips between themselves and the movement is not stroke. The situation is different if you want to make a smooth floor indoors, non-plastered doors. For example, in the kitchen, dining room or living room.
Stages of docking parquet board and tiles.
What will take:
Cork compensator when docking parquet and tile allows you to make the surface of the floor perfectly smooth without sharp drops.
The surface for the junctions is lubricated with oil. Can be used for processing sewing machines or automatic trimmers. It is convenient to apply several drops from the bottle. A clean cotton disc needs to be confused on both surfaces. This is done in order for the sealant, in case of inactive use, it can be easily separated from the tile or board.
Then the bottle is inserted into the gun, and smoothly without tremor movements, the composition is found in the interval where the joint should be.
If it turned out to be too protruding edges, then with the help of a spatula, the surplus should be cleaned right with the floor. Thus, the compounds will be impeccable.
It is best if the sealant squeezed and smoothed layer will be chosen in the seam. This will help his durability - to hurt such a strip will be a problem.
Complete drying of the composition will occur after 24 hours. During this time, you need to try not to walk along this section of the floor, in order not to cause the joint shift.
The method is not the most time consuming, but requiring accuracy.
Errors when working with sealant Siliconov:
What will take:
Options for overhead planks for docking flooring.
The sheets are cut from the sheet for seam sealing. They are made with such a calculation to be 2 mm wider than the gap. Because for fastening such material, nothing will be used - the cork should be tight.
Upon completion of work with the seal, it is necessary to spend cyclics and grinding. Then the connection and the appearance of both surfaces will be perfect.
Since the installation includes the use of special machines for subsequent work, then, of course, you need skill in work. Better to trust the pros.
Errors when working with a plug:
Additionally, it will be necessary:
As in the case of a sealant, two surfaces wipe with a tampon or a cotton disk.
Then gradually squeezing the mass of the tube, the liquid cork fill the gaps between the tile and the board. If the floor in both planes is perfectly smooth and is single cloth, There should be no problems. Otherwise, it is necessary to navigate on the edges of the surface that above. And on them equal to the plug.
Docking options different coatings With the help of the clad.
After the frozen of the surplus is cut off with a knife, while trying not to damage either the boards or tiles. It will happen not earlier than in a day. But the flaws from the surfaces need to be removed immediately so that the adhesive composition is not tightly pressed. Make it is easy if the floors were covered with oil.
Then work on cyclove and grinding. As it is clear from writing, work is simple, but with cyclo house master may not cope. However, if you dare, it will turn out.
Errors when working with liquid plug:
List of required:
First cuts off the required piece of material.
Installation of flexible melting for docking floor coatings.
It is worth considering that its length is the entire segment of the joint plus 1 cm. Pencil needs to be outlined the border where the profile of the blocks of connections will be laid. Simply put, to circle it along the contour so that the middle rushes just on the seam.
Then you first need to drill holes in the tile. Make it will be very difficult, because it has the property to crack. Therefore, drill is used good quality, diameter no less screws. The points where the drill will be sent, you should sink a little stray, slightly sniffing the top layer of ceramics. So the drill will be easier to enter and the risk of cracks of the tile will decrease.
If the profile already has ready-made holes, it is simply applied and fixed by self-drawing through two fasteners elements. This is for smooth overlays. Then twist the rest. However, if the profile is clean, it must be prepared in advance - drill holes in accordance with those places where they contain tiles.
Profiles are conveniently engaged in drops of heights of different surfaces. Typically, parquet is lower than the tile, if it was laid a non-professional, so the pad is performed in this compliance. It is necessary to ensure that the profile adjustment goes completely. And if this does not occur because of the big difference in the height of the surfaces, then from such a material for combining joints should be refused.
Thus, the parquet board and tiles are docking PVC profiles or metal.
The dimensions of the multi-level stainless steel thresholds.
Errors when working with profiles:
All listed seeding options are too afraid of moisture. In addition, perhaps, traffic jams. The sealant falls off, the profile can go rust. What to do, because wet cleaning an integral part of maintaining in the house of cleanliness? The answer is one - do not overdo it. You can wipe it, it is impossible to wet. And be sure to dry!
Floors are the face of the house. Even if they are simply clean, the impression of the comfort is created immediately. And if the surface is beautiful connections, then there is simply no words. Decoring them must be made thoroughly. First, it is worth thinking whether the skill and patience is enough for such a work, and then start. One thing can be considered exactly - any independent process will bring fruit, if there is a desire to make your home unusual and beautiful.
During the repair and cycling in Nakhabino, the hosts often face the need to connect two flooring such as parquet and tile. Since parquet - natural material from natural wood, it is impossible to do here smooth compound junction Depending on the microclimate in the house under the influence of various factors (heat, cold, moisture, etc.) wood can be subjected to displacement, since this material It has the highest deformation coefficient. Therefore, it is important to leave the gap between the tile and parquet in the range from 5 to 15 millimeters. Subsequently, this space can be hidden using a threshold.
In addition, the distance between the joints is noticeably visually, moisture will begin to fall into such a gap, the dust will be clogged, which will lead to the rapid wear of the floor covering. In addition, the presence of a gap brings discomfort when walking on this floor, since irregularities are immediately felt even through shoes and can cause a fall.
Which of the listed methods is better to use, it should be addressed on the basis of a particular case. In order to bring the gap look aesthetically and did not cause discomfort to the owners, it is better to immediately entrust this business and
The connection of several finishing materials makes the room beautiful, original. Such contrast will help you implement the most brave designer ideas. Naturally, special attention should be paid to the types of cladding used. Some of them do not docile so easy. However, there is nothing impossible in the world.
So, the tile is a special material that is good "feels" temperature change. However, humidity does not have significant impact on it. This is what provides a minimal degree of linear expansion. But the parquet is able to respond practically to all external influences. That is, under the influence of moisture or temperature differences, it is able to narrow and expand.
Combining these materials without a special deformation seam can lead to the fact that you once detect your floor covering with a house.
Therefore, the compensation cumulative clearance must be present. Naturally, it should look beautiful and smoothing the possible height difference between tiles and parquet.
Very beautiful such a combination looks in the kitchen. Here in the working area can be used tile, but in the zone where dinner table, Parquet stacked. There are several ways to design, which we will consider in detail now.
This method is considered the fastest and most durable. To work you may need:
During the choice of the funds you will connect the tile and parquet, you need to consider it specifications. In particular, pay attention to the parameters of elasticity. They should be high, because the materials presented are very difficult to combine.
To glue the tile and parquet in the gap Place the locking substance and evenly distribute it. After complete drying of the adhesive composition, it is possible to seal the seam by the usual grout for tiles. Note that its tone should coincide with the color of the finishing materials. Only in this case the junction can be made neat and beautiful.
Such a connection method is considered the most durable and reliable, since the seam is almost impossible to destroy.
While working, filling the clearance with a sealant or glue, it is necessary very careful that the substance does not hit the parquet.
If it didn't work at all without dirt, try to remove excess composition from the surface of the finishing material. Make sure that the seam width is the same throughout its length. It is important that the joke is maximally accurately in height.
This method also has the right to life. It is that tile and parquet are connected using a fugue for ceramics. The advantage of this method is:
Disadvantages are much larger:
In addition, the gap between these coatings should be 3 mm, and to achieve this, you need to try to very much.
Note that the contact connection of two different structures and properties of materials cannot be in principle. They differ significantly in terms of the level of elasticity, which contributes to the destruction of the coating.
In order for such a way to be the most efficient, parquet and ceramics should be laid according to all installation rules. That is, laying materials is perfectly smooth. The thickness of the cork fixtors ranges in the range of 0.6-1.5 cm. Mounting the plug should even before grinding and varnishing parquet.
The submitted seal has a high degree of elasticity, so screwed it very carefully and carefully. During the work of all the work, it is necessary to ensure that the width of the compensation seam remains the same.
This method of compound has the following advantages:
This material provides a very durable seam between the parquet and tiles.
Such elements will help to docile these types of flooring, even if there are height drops. At the same time, after installing the threshold, this difference is not visible. It is possible to use elements both for a conventional connection and for non-standard zigzag.
Thresholds are made of plastic or metal, as well as wood. In stores you can find big choice color solutions. After installing the threshold, the floor looks beautiful, completed, divided. The transition from one type of floor covering to another is very smooth.
There are several ways to install the hole:
On the picture step-by-step instruction By installing the clad in the seam between tiles and parquet. Often, a profile is used to design such a seam. It can be metallic or plastic. The latter can have different shades. On a metal product, a decorative tape can also be pasted.
The profile is a narrow or wide, equipped bellows or not. The product is usually placed on top of the gap and is screwed by self-drawers. It is impossible to call this method of connection is very beautiful, but it hides the height difference between the coatings well.
So that any docking was high quality and beautiful, laying out ceramic elements, try one row not to be stuck.
On the surface of this layer, you need to set the level lighthouses for which the parquet is subsequently mounted. This needs to be done, as in most cases the extreme part of the tiles will need to be slightly lifted for the substrate.
After the wood coating is laid, you can start gluing the last row of ceramics. If you decide to close the compensation seam with molding, then the accessories should have a perforated basis. This will allow achieving full contact between two outdoor coatings.
As you can see, there are a large number of methods for connecting different finishing materials. However, you need to choose exactly the one that will meet all your requirements, because it is important not only beauty, but also quality. Good repair!
Non-quality coat joints - possible reason Domestic injuries. Is it possible to make a joke of tiles and laminate, boards and porcelain stoneware, parquet and vinyl at all without a transition (vengement, visible border)? We found out the designers as they offer safely and beautifully sticking outdoor coatings. And maybe high-quality threshing is not so bad?
Sust or not
Some designers respond to "no". Than to break your head, how to dock the laminate and the tile without a neck, it is better to give up something to combine something at all. At least in the kitchen-living room - so as not to crush a single space and not turn the apartment to the "flooring shop". Another thing is if your decision is decoratively justified - like a tiled carpet in the photo in this kitchen.
Laura Hammett Ltd.
"Collect the will in a fist and choose one option, - advises architect Victoria Korneev, SHKAF Design Bureau. - Modern manufacturers offer a wide range of materials that can live in wet areas. This is a parquet board, and cork coating, and various bulk mixtures. . If the design under concrete or stone seems to you cold, choose a porcelain stoneware with the imitation of a wooden surface, just do not connect natural tree And imitation, it is impossible to achieve an ideal hit and the texture. "
Ekaterina Lovyagina In the photo: Panel from Metlah tiles, "glued" into the oak floor by the fireplace - not only practical, but also beautiful
Another part of the designers considers the compound of different floor coatings in one room justified. This technique allows you to zonail the apartment without the construction of partitions, makes the design more difficult and more interesting. For example, in the kitchen it is practical and profitable.
Teplitskaya design
Idea: "Cold" materials (tile, porcelain stoneware) imply the need for a "warm floor". Heating throughout the area will no longer. But if you want pleasant tactile sensations, with the practicality in operation, there is a way out. Put the "warm floor" only in the zone with a tile at the table tops (where the hostess is most often). And lay out the rest of the floor of the floor kitchen with a "warm" coating, such as a board, cork or the same laminate.
"Put the strip of strip in 60-80 cm along the table top with a stove and washing, it will greatly simplify cleaning," the designer Alena Vlasov advises.
The connection of the laminate and tiles in this case should be without a spawning. Everyone will tell about it who at least once squeezed dust from under the connecting plank.
Ekaterina Vladimirov
The joint of the materials most often passes on the border of individual rooms: rooms and kitchens, living room and bedrooms, hallway and room. The most popular combinations on the floor - tile and laminate, porcelain and parquet, array and marble, vinyl and tile. Sometimes there are two identical coatings: for example, two pieces of linoleum or multidirectional laminate. Connection in each case can be performed different ways. As a rule, heterogeneous materials are joined using aluminum cladding, silicone sealant or cork compensator. But there are other options.
We plan to join on the screed stage
The question is how to make a junction of laminate and tiles without a thoring, you need to decide before the start of repair. "If you are going to keep the materials, it is very important to choose the coatings in advance and indicate builders thickness, for example, tiles and boards for the proper formation of the finishing screed," advises the architect Irina Melkova.
Architectural Bureau Archslon
To carefully dock materials, you need to correctly calculate, that is, take into account the thickness of materials, substrates and adhesive base. Take, for example, tile and parquet. We fold the thickness of the tile and the layer of tile glue. Then - the thickness of the parquet, plywood, glue. The difference between these values \u200b\u200bdetermines the difference in height in the screed. Usually builders laid several millimeters of stock, and the final correction is done with glue. So, a layer of glue under a porcelain conductor can be from 4 to 20 mm.
Photographer Mark Kozura.Choosing the plywood of the desired thickness, you can also affect the height of the parquet. If the parquet or board turned out to be slightly higher, the differential is removed by cycle.
But if the tie remembered late, and the floors in different rooms Not coincided in a height of more than 5 mm, it is easier to buy a multi-level docking profile.
Kazantseva Tatiana
Deculating the joke
"How to arrange a connection depends on the method of fastening the coating," the designer Vera Vasilenko is attention. There are two options.
First option: both coatings are attached to the ground "tight". For example, a tile and engineering board on a plywood basis are glued to the screed. For ensuring that the board "breathes", the deformation seams correspond. The jack between tiles and board can be filled with different compositions, for example, a polyurethane sealant or epoxy tiled grout. And you can use the docking profiles from the metal - there are a lot of them on the market. "There are beautiful thin profiles that are installed before laying tiles, such as ProfilPas, Bautec," beliefs Vera Vasilenko.
UD Bàse.
The second option: one of the coatings - for example, a parquet board, a laminate or a plug - is laid by a floating method on the substrate. At the same time, the second coating can be attached "tightly", but then the place of the junction will be rigidly fixed on the basis of the floor. If it is impossible, it will only be used to use T-shaped metal thresholds with a minimum width - preferably not more than 1 cm. Do not look for such thresholds in building supermarkets or in markets - only in specialized companies.
Important: According to designer Anastasia Ermakova, the builders sometimes insist that the docking seam was wider, if on the floor - soft ash. Oak "walks" much less. How "freely breathes" wood depends on the breed.
Rad Design Inc in photo: Tile and laminate butt - first mathematical task. On average, the meter of laminate needs to lay 1 mm of the compensation gap. But it is not necessary to hoped on a plastic filler - better to hide the clearance under plinth
Gleb Polonsky
1. Grout for tiles
The gap between tiles / porcelain stoneware and any material fixed by a non-floating way can be seen by the same grout that was used for tiles. This method is good for sealing wavy seams. "We have repeatedly practiced with a tiled grout, the artist's qualifications are very important here," recognizes Designer Svetlana Kornienko.
Dacha-Buro.
IN modern interiors Often you can see the fashionable reception: the use of octagonal tiles ("octagon") and hexagonal ("hexagon"). Multicolored "run" to others decoration Materials - both on the walls and on the floor. According to the architect Oksana Kostyuchenko, the junction between the engineering board and the multifaceted tile will look great, if you fill it with a high-quality polymer grout for porcelain stoneware. " Technological process You can wrap in favor of decorative plan. A compensator can be a two-component grout for wide seams with a crumb of one of the jacket materials, such as marble, "offers a designer Nadezhda Davydenko.
Important:Grout is not suitable as a compensator when using materials that have an extension property.
Design Studio Catherine Popova in the photo: The cork compensator is tinted in the color of the wooden floor and is covered with a protective composition so that it does not start crumble over time
2. Cork compensator
One of the most popular ways to make a junction of tiles and a parquet without a spawning - put between them the cork compensator of the desired shade. It looks like "Reika" from a pressed plug, sometimes sold in the form of sheets. it soft Materialwhich is able to survive the natural expansion of parquet or laminate. It is suitable for wide seams, attached to parquet glue. Sale cork compensator and without processing - under grinding and varnishing together with parquet. As well as in the form of a painted and lacquered plank. This is better not to grind, otherwise it will begin to crumble.
MARINA SARKISYAN (Marina Sarkisyan)
In the photo: Tile and array shares cork compensator
"Through the cork compensator is made between parquet / massive board and tile. It is beautiful and convenient: no one will turn into this place in this place, "said Marina Ananya, the head of the design bureau of Catstil. - Clay floors on the glue generally fit the finish to the tile. From the traffic jam you can lay out drawings of any complexity. But in the case of "floating floors" will have to use moldings. "
Cons of cork compensator also have. First, a limited choice of shades. Secondly, the cork although it is compressed, but sometimes it is not enough to compensate for the expansion of the laminate on a large area. Therefore, as a rule, in the premises more than 25 sq. M. The jack of tiles and laminate is not made without a clamp. Thirdly, it is common that the traffic jam does not stand the shrinkage of the house and crumble. According to Designer Tatiana Lean, it happens that the cork compensator "crashes" from the groove. However, most designers associate this phenomenon with improper laying of floors.
Design - Ecole Bureau
"To make the compensator" to dust "at the shrinkage of the house, the house should" sit down ", as with an earthquake that, subject to the guests and SNiPs, it is simply not real," Irina Melkova is sure. Her colleague Tatiana Krasikov believes cork compensator the best option Get a jack of tiles and a parquet board without a neck. "I never came across that he was falling out from the movements of the house," the designer assures.
Lavka-Design in the photo: The joints between the tree and tile are embossed "liquid cork" and covered with varnish
3. Liquid cork
The joints of the tile and parquet without the imposition can be filled with a liquid cork (cork sealant). This is a composition of cork crumb and glue, the material is soft and elastic. You can choose the composition under the shade of one of the stuck coatings. Minus - looks "alien" on wide joints.
Designer Angelica Safina does not advise using a plug if the seam is wider than 7 mm. But in narrow seams - up to 5 mm - a large crumb to drive is not easy.
Important: Linoleum and carpet plug do not connect.
4. Silicone and acrylic sealants
Architect Maxim KharitonovtsTets optimal option For sealing seams between flooring silicone or acrylic sealants. "They are perfectly combined with the parquet and tile, is a member of Dmitry Korshunov with a colleague," and during the shrinkage, the building will remain in prior odd. Acrylic, unlike silicone, can be painted and laminated after drying. "
Elastic silicone sealants are sometimes used for docking laminate and tiles without imposition, including for processing curvilinear seams. But here you need to correctly calculate the technical gap. In addition, some silicones lose elasticity and over time and become solid.
In the photo: the jack of parquet and the tiles without a neck. 1,5 mm wide width filled with special silicone color parquet
"It is possible to use silicone sealants if the floor covering is mounted on a screed by landing on glue or using mechanical fasteners, that is, not a floating method," resembles an ANNA architect boring, SHKAF design bureau.
Svetlana Yurkova
Choose profiles and thresholds
Special indications for creating a node is a significant height difference and floating coatings. "Sometimes a thin metal T-shaped profile, competently chosen in color, is the perfect solution," says the designer Nadezhda Davydenko.
Indeed, the choice of profiles, moldings and click-systems today is very wide. And with it - and the choice of options, how to docile laminate and tile or, for example, linoleum with other coatings.
Julia Karagodina
"The cork compensator is the same yesterday as the aluminum flames," said Architect Roman Korotkov. - His aesthetic properties are not much better, and the complexity of work is high. It is much easier to use special metal profiles for floors - will come out elegant. They are suitable not only for designing a joint of different materials or creating a technological seam, but also as decor. Such profiles are of different thickness (from 2.5 mm) and height - that is, it is possible to choose the option for the material of any thickness. They are released different colors and make from different materials: brass, aluminum, zinc, chrome, gold, painted by RAL color table. There are different shapes: M-shaped, T-shaped, P-shaped. These profiles can be bend and molded to create any decorative drawings. "
Marion Studio. In the photo: marble and parquet butt performed using a brass profile
Evgeny Shokogo does not have complaints about traffic - for 12 years she did not care anything on any object. But if the budget allows, the designer advises to pay attention to brass and steel thin profiles: they look great and any shape can be made. "
Metallic M-shaped profiles can go in a tandem with a cork compensator -task, closes the plug strip between coatings or any other filler. Many profiles allow you to make a seam in one level with floor coverings. The profile itself is attached to the floor, parquet or laminate is inserted inside. On the other side of the Splat.
The designers have their own preferences in the threshings. So, Olga Pasyakinetsheet to those who think how to combine tile and laminate, select laminated thresholds from one collection with laminate. Similar thresholds make carpet manufacturers and engineering boards from wood. In this case, one hundred percent coincidence is guaranteed. Designer Olga Papushkinchitstatts that stainless steel bellows are always stylishly that they would be connected. And Architect Maria Kitaeva is not indifferent to elegant profiles from copper and brass - orders them from masters working with metal. "To those who consider modern thresholds not very aesthetic, I advise you to remember which thresholds were in Soviet apartments, compare and conclude," the architect is ironic.
Qt Interior Design.
In the photo: docking laminate and tiles. Without the birth- used Neat T-shaped profile
Indeed, profiles not only changed technologically, but also decreased strongly. "Usually we use a narrow T-shaped metal profile," Designer Ekaterina Grigorieva says. - As a result, a strip of a width of only 2 mm remains between the connecting materials. This implies the perfect trimming of materials, since such "threshing" cuts do not mask. For such a material like laminate narrow option Not suitable. "
Dyer Grimes Architecture
I jok uneven sow
Nonlinear connection of the tile and laminate, like any coatings - the reception is complex. The perfect coincidence of the modules will be required. Designer Artemy Saranin recommends how to abandon the curves of lines in docks. But if without zigzags and angles in any way, then the materials for the docking line must be adjusted in advance on the lecture, it is desirable - in production. Then the gap can safely "enjoy" in the color of the tile or porcelain seams.
Design - Ecole Bureau
Architect Irina Melkova advises to look at the budget. If it is limited, and the docking of the laminate and tiles is designed smooth, it is better to choose a cork as a compensator or abandon the bends at all. "In a more expensive embodiment, the docking in smooth lines can be made with a thin steel strip over the plug, made according to the flows. Steel is painted by RAL, the docking looks very aesthetic, "says the architect.
Design - Ecole Bureau In the photo: Figure junction of parquet and tiles made using a cork compensator
According to the designer, Svetlana Udzilauri, a neat dock with a curved edge can be issued only with a metal. Her colleague Irina Absalimov believes that the choice is wider: "Kahrs and Tarkett flooring manufacturers offer flexible transitional and connecting thresholds for connecting surfaces with rounded trimming. They are heated and attached the necessary direction. "
The flexible threshold of thermoplastic can take any shape, and in the palette of colors gives a choice of decorator. "But if the house already" standn up "and will not give a shrinkage, the cork compensator is preferable - in my opinion, it is aesthetically more noticeable," the designer Olga Karpova believes.
Bay In the photo: Tile and parquet are laid without a seam. Thanks to the stack of the joint between tiles and parquet looks like a junction between parquet boards
Icy« seamless»
Some designers managed to achieve "seamless" docking materials. According to Inhi Tartakovskaya, this is possible if the levels of the surfaces of the surfaces are highly derived and there is perfect cut. Sticks are best looking if the materials with the edge treated at the factory are joined. "Jewelry region can only make a good master," the designer Irina Kashayeva agrees. - The edge needs to be processed with a suitable composition of the model or paint. "
Natalia Spivak and Hope Bartzova In the photo: the most cunning option, how to connect tile and laminate without a clamping- Choose a laminate tile
Elena Ilyukhina Design Studio
What to remember:
If you are going to poison different coatings, decide on them until the formation of the finish tie. Then it will be possible to derive levels taking into account the thickness of materials, substrates and adhesive bases.
With a drop of heights of more than 5 mm, it is easier and cheaper to use a multi-level docking profile.
If the screed is already done, it is possible to level the differential with the help of glue (tile) or plywood thickness (parquet).
If the parquet or board turned out to be 1-2 mm higher, the differential is removed by cycle.
If both coatings are attached to the base (for example, a tile and a board on a plywood basis), the joint between them can be filled with a polyurethane sealant or tiled grout, and you can get out and use elegant metal connecting profiles. They are of different thickness (from 2.5 mm), heights and shades of RAL. Some can be bend and molded. Look for such in specialized stores - in constructionarkets they are not found.
Stacklab
If at least one of the coatings (board, parquet, laminate) is placed by a floating method, it is better to use T-shaped metal thresholds with a compensation gap for expansion. Another option - rigidly fix materials (for example, tile and parquet) on the place of the joint, and the compensation gaps lay only under plinths. This method is used in small spaces.
If you are joining a tile and parquet without a seam, choose the coatings from the chamfer - so the junction will be imparable.
The seam between tiles and other rigidly fixed material is easiest to close the same grout that was used for tiles. This is especially convenient if the seam line is wavy. For wide seams, you can use a two-component grout with crumbs of one of the jammed materials - for example, with marble.
When docking the "breathable" materials without a threshold, it is better to use not tough grout, and elastic compensators: a plug (liquid or strips) or silicone / acrylic sealant of the desired shade.
Choosing a parquet, engineering board or laminate, immediately look at the threshings that go in one collection with the material. In this case, you will absolutely get into color. Flooring manufacturers also offer flexible thermoplastic. It is warmed and give the necessary direction. When heated, such a profile can take any form.
Hovanskaya Olga.
Buro Brainstoorm
Jan 5, 2018 Sergey
It is very nice, fashionable and conveniently located the location in one room of two different materials of the floor covering. For example, tiles and parquet. To independently produce such, you need, first of all, stock knowledge on how to combine tile and parquet.
Modern designers advise to combine in two ways: monophonic and contrast. Adherents classic style May pick up tiles and parquet about one shade or with a small difference in color. But Extravagant style lovers can pamper themselves with something bright, contrasting.
The combination of two such materials gives an excellent effect to your interior, giving saturation and originality. And if you integrate the backlight, the effect will exceed itself.
Of course, not only aesthetic goal is pursued by mixing the floor covering, first of all, these are utilitarian purposes. For example, in the hallway, you can split the zone. Where you are pereobed, you can put it, which is more resistant to various pollution.
The kitchen is mounted on the work area, i.e., where the stove is located, sink and work desk. After all, ceramics more moisture resistant than parquet. And the wooden floor is used in the dining area, so that the feet were warm, and the view was cozy.
In order for the interior to be completed, you need to think through every little thing. Of course, the place of the junction is ugly, if it is not decorated. It is for these purposes that some tricks use.
The junction, for example, can be connected using a hole, molding, cork compensator or sealant. The thresholds can clearly distinguish the space or, on the contrary, give a smooth transition to pieces.
If you glue the seams, take care of. Or choose identical colors exactly matching, so there will be no difference between the parquet and tiles.
Pickles of parquet and tiles There are several. And each of them has its advantages and disadvantages, having studied which you need to choose one. Because during repair work Amend the method will not be possible, otherwise unforeseen complications may occur.
If you are interested in how to dock a tile and parquet most, stop your choice on a lipid dusting. To do this, you will need only any adhesive composition: construction foam, sealant, assembly paste, glue or silicone. When choosing, focus on the high elasticity of glue, as ceramics and wood are not very compatible materials.
In order to glue a tile with a parquet, it is enough to apply an adhesive substance to the joints, evenly distributing it around the perimeter. Next, you are waiting for everything dry and raise the usual tiled stamps of the seam.
It is worth noting that this method is the most reliable because it is subsequently easier to tear off the parquet and tiles than disconnecting the joints. With all this, you need to make a maximum of effort in order to gently fill the seams with glue and then get rid of surplus. You also need to strictly monitor the accuracy of the joint in height and scatter in width.
This method is characterized by the fact that the seams after repair are practically not visible. They are embarrassed by a fugue for ceramics, which holds badly on wooden parquet. Therefore, during the operational period, it will have to constantly squeeze the gaps.
During mounting work You need to perfectly customized tiles to parquet in height and in width, and the lumen between them should be 2-3 mm. It is also impossible to allow direct contact between the two floor coatings, as they have different coefficients of elasticity, which negatively affects the facing.
In order to take advantage of this method, you need to put parquet and tiles in all respects. Cork compensators have a thickness of 6-15 mm and parquet varnishing and also installed.
Since the cork itself is elastic, you need to screw the cork compensator in the gap between tiles and parquet. The width of the slit should not change throughout all the work.
Such a connection is durable and reliable ,. In addition, it is an environmentally friendly material.
To date, we produce a very convenient view - a liquid cork that consists of glue and cork crumb. They squeeze this mass directly between the joints, but with a margin, because the liquid cork gives a good shrinkage. After complete drying, the surplus is cut with a special knife.
You do not know how to connect the tile and parquet so that there is no difference in the height between the coatings? Then pay attention to the pitch with additional accessories. Namely, the boards and moldings. They are used for both direct compounds and zigzag and similar, but are made of wood, metal and plastic. Produced in a wide range.
This accessory is capable of drastically distinguish between the space and create a smooth transition between the coatings. The floor will look pretty neatly and organically.
Both the boards and moldings are different by the method of fastening. You can purchase accessories consisting of two planks. One of them is attached to the floor, and the second is put on top with the help of a latch. In such a way, you can not see the fastening elements, and therefore they call it hidden.
For open way The gap between floor coatings is inserted into the thresholds, holes are drilled, and reinforced with screws. But this is only if the rough base is not concrete. In the opposite case, the plate is attached to the dowel.
Many use special plastic or metal profiles. By appearance They can be with a damage and completely smooth, narrow and wide. The installation of the profile connection is quite simple, as it is necessary to put it on top of the gap and fasten with self-draws.
Of course, this method is not different in grace, but pretty well hides the irregularities of the height between the parquet and tiles.
Before docking the tile and parquet in a straight or cork method, leave one row blank. First you need to set the levels on the ceramic surface, and then they put parquet in their marks. The fact is that, most likely, it will be necessary to raise the extreme part of the tile to make the substrate. Only after the parquet is mounted, you can lay the last row of tiles.
When the threshings are connected, ceramics are fully laid, leaving the gap of 3-5 mm. Next, parquet and moldings or moldings are installed. To achieve full contact with tiles, and with a parquet, apply accessories that has a perforated base.
