House, design, repair, decor. Yard and garden. Do it yourself

House, design, repair, decor. Yard and garden. Do it yourself

» Forward wallpapers or laminate. Shook wallpaper or laying of laminate that before

Forward wallpapers or laminate. Shook wallpaper or laying of laminate that before

Hello! Tell me, please, first lay the laminate or shove the wallpaper? If they first get the walls, then the dust from the cutting of the laminated floor and the plinth will certainly be seen on the wallpaper canvases. And if you first mount the floor covering, then while working with walls in the room is likely to hold a high level of humidity, which is not good for laminate. Very much need a professional council, preferably with explanations.

Answer

Good day! The question is, at first glance, controversial. But in fact, the technology has been worked out for many years and the correct algorithm of actions with finishing decorative materials has been revealed.

Remember the simple rule: on fully prepared ground reasons, or rather finishing, is carried out from top to bottom. That is, the order is this:

  1. apply a ceiling coating (in some cases, the exception is stretching and complex acoustic systems);
  2. handle wall;
  3. make floor.

Thus, it is logical first to bleach the wallpaper, wait for the drying of the glue, and then lay the laminated coating.

To prove to turn to the technical part. In the instructions K. outdoor material There is always an item:

"Due to the hygroscopicity of laminated coatings (products by 90% consist of wood), the installation should be carried out after the end of all" wet "works."

But the wicked walls with wallpaper belongs to such events. We now get acquainted with the instruction of glue compositions for wall roll Materials (fiberglass, paper, flieslinic, natural, vinyl):

"Since the start of work and until complete drying, the adhesive and doors should be closed."

This is necessary in order to eliminate the premature drying of the adhesion composition, the formation of non-flimsy regions and swolves on the surface of fixed wallpaper. In a few days, an elevated level of humidity, reaching 95%, is established from the air exchange room for several days. The maximum allowable humidity parameter for laminated coatings is 60-70%, but not more. If the bar is exceeded, they will smell, change geometry, and the floor is swept away. And there is no guarantee that in a month or another finishing material will come to normal. Rather, on the contrary - you will be forced to partially or fully change it to the new one.

Proof of high humidity - dwarked windows.

Arguments like "dust will fall on the wallpaper", "when installing can scratch the walls" or completely original - "Need smooth surfaceSo that you can put the rolls. "Do not stand criticism. First, ask the finishing masters to work carefully. This is easy and in no way infringe on someone's rights. Secondly, offer workers all cutting processes in another room. Thirdly, when experts are finished to fit the floor, simply speaking the walls of the usual household appliance. And the latter - any foundation prepared for laminate is characterized by smoother and strength. Estate the polyethylene film on it and forward - to measure, customize, apply the adhesion composition, fix.

Another argument in favor of sticking the wallpaper in the first place is the impossibility of working with cloths without a stepladder or a special table (the so-called building goats). Support legs auxiliary equipment Can damage the surface of the laminated parquet. Of course, many are trying to protect it from scratches using cardboard linings, pergamine, substrate, dense polyethylene film. But in practice, the hired brigades of the finishers for the flooring almost do not follow, so the formation of defects is inevitable.

When you need to lower the laminate forward

What if the master insists: first you need to put a floor covering. Require from it to justify such a solution.

The first reason for changing the right level of repair is the lack of wallpaper actual (did not have time to bring, could not choose, etc.).

The second is the convenience of work. A similar argument of the finishing, which puts the laminate or specializes in wall coatings, note immediately. The main thing is not comfort, but the quality of the performance and preservation of mounted building materials.

And the third - "burning" deadlines for the implementation of a certain type of work. These are external circumstances that are independent of the wishes of the Master. Therefore, all risks assumes the customer.

Thus, the correct sequence:

  1. prepare the basis for wallpaper;
  2. work the base floor under laminate;
  3. install in the opening of a box bar (door do not hang on the loop);
  4. glue the wallpaper;
  5. after drying the glue and ventilation for 3-5 days, laying the laminate, mount the plinth.

Tip! If you need repair masters, there is a very convenient service for their selection. Just send in the form below detailed description Works that need to be performed and offers to you will receive offers from prices from building brigades and firms. You can see the reviews about each of them and photos with examples of work. This is free and does not oblige anything.

The question is that it is better to do first - glue wallpaper or laying a laminate, has always been the main reason for the discussion during the repair. Our article will allow you to consider the major arguments regarding both methods. And how to act personally, decide for yourself. After all, the point of view posted in the article is not true. In this case, there are always its positive and negative sides.

Pros and cons of the other way

There is a lot of arguments towards the initial pasting of wallpaper and on the other hand, laying the laminate. How many people, so many opinions. And the professional professionals are no exception. But nevertheless, both methods have their own positive and negative sides. Therefore, it is worth carefully considering that first: laminate is clapped or wallpaper glued.

And oddly enough it sounds, but one of the significant criteria for choice is the formation of garbage and other construction waste after work. After all, the emergence of a large number of unnecessary waste can cause a late start of other construction manipulations. Therefore, most masters agree that it initially needs to produce that stage of repair, which is characterized by fewer garbage.

Important! Repair in which you need to lay a laminate is considered one of the least dirty. Dust and dirt quite, of course, not avoid. But there will be little construction waste. Even in comparison with the sticking of wallpapers on the surface of the walls.


Why initially you need to blow wallpaper?

Initially, it is recommended to threaten well to think about all the steps of repair, during which the surface of the walls will be accumulated. At this point, you will be able to make sure what kind of work should be priority. Next, consider the fundamental factors that it is worth paying special attention:

  • in the process of repairing the laminate, compared with another flooring, for example, a linoleum or carpet, does not need a fit under the surface of the wall. Therefore, it is not necessary to worry if the sticking of the wallpaper has already been produced earlier. This wall material will not be damaged when repairing the floor;

Important! Laminate in the process of laying is mounted at a certain distance from the wall. This becomes possible when using special spacer wedges. In addition, during the repair of the surface of the floor, the garbage and construction waste will remain. This is another argument in favor of laminate. But this, of course, provided that preparatory stages Repair has already been fulfilled, and you will not start new construction. Stowing wallpaper on walls and laying of laminate should be performed after all preliminary construction manipulations.

  • But there is another side of the medal. Not so simple. You can stumble upon such laminated material, which is characterized by a special sensitivity to the evaporation of glue. Then the level of humidity can increase in the entire room.

Important! If you wish to make high-quality protection for laminate during repair, it is fully covered with a polyethylene film. You can use another material, the main thing is that it provides a full-fledged cover.


Laminate protection when sticking wallpaper

This means that the film laying should be made in any case, whether the first sticking of wallpaper or laminate installation will be. Practice shows that all types of modern wallpapers will be vinyl or phliselinic, achieved full drying only in the absence of drafts. Including the vessels must be closed. Such an atmosphere will cause a sharp increase in the level of humidity. And the moisture released during evaporation will have a negative impact on the laminate after repair literally within a few days. Upper laminated laminate coating, if it is not distinguished by moisture resistance or water resistance, it may be damaged.

But such a situation will be a wage only in the event that you will change the wallpapers every year. If a redecorating It will not be so frequent, everything is fine.

Is it possible to take a sticking of wallpaper after installing the laminate?

From a technical point of view, the secondary salary of wallpaper walls is permissible after laying the laminate. But on the other hand, it is better not to do with repair. Indeed, in the process of sticking a wallpaper material, you can damage the upper laminated coating. The adhesive compositions used may adversely affect the quality of the laminate, leading to the appearance of spots and other damage.

That is why the opinions of most specialists working in the field of repair and construction are converged in one: it is better to immediately glue wallpaper on the walls, and only then put the laminate on the floor. But if it already happened so that you did not know about it and immediately put the laminated coating, do not be sad. It is worth accurately performing all construction works When repaired, and the floor is covered with film, and everything will cost.

Also do not forget about other factors that can damage the laminate. This is furniture and decor on metal legs. In the process of their movement, it is necessary to be extremely neat so as not to scratch the flooring. In this case, the standard polyethylene film is not suitable. It is recommended to apply something dense and durable. In building stores, you will help you with the choice.

Stages of proper repair

Answering the question of our topic: What used to be laminate or glue wallpaper on the walls, it is important to understand that there are own patterns in construction. This is a whole technological process, as in production, follow the phased implementation of which is very recommended. Only so repair will be performed competently.


Gluing wallpaper on walls during repair

Most of the opinions of professionals converges on the fact that it is originally worth the walls of wallpaper, and only then begin to mount outdoor coating. And at the same time it does not matter, it will be laminate or linoleum, in principle, the sequence of repair remains the same. So:

  • First of all, it is recommended to prepare walls to repair. It is from this that will depend on how high quality wallpapers will be glued.
  • Then it is necessary to start the screed, or when necessary to create the so-called black floor.
  • Then sweeping wallpaper on the surface of the walls. At this stage, we will not stop in detail. It all depends on the type of wallpaper used. It is only important to strictly follow the instructions for one or another wall and ceiling material.
  • After complete drying, the wallpapers start laying the laminate. When repairing it, its pill is performed first, and only then the installation of plinths and other related decoration is performed.

Conclusion


Naturally, everyone who has read the article will highlight the most significant arguments for themselves. And, of course, everything is done taking into account specific conditions of repair. But, no matter how it was, it is better to glue the wallpaper right away, and then laying the laminate. Such a sequence of work is adhered to most of the construction sphere professionals.

In the process of repair work, time is suitable for determining the next actions: put the laminate, install the doors or shove the wallpaper. All these types of work must be carried out with a certain thoroughness.

For each work it is necessary to use its own specifics. Is there a certain order of such work?

What is first - wallpaper or laminate?

When, during repair, it comes to pasting wallpaper or laying laminate, it is difficult to choose the sequence of these works. It is necessary to determine how to do in this situation.

Degree of dust formation during operation, specificity technological process, Volume is determining factors in choosing a sequence of types of repair work.

Many masters and specialists lead a permanent discussion about the priority of work. Most of them are inclined to the version that it is best to accommodate wallpaper, and then lay the laminate.

Prior to repair work:

  • Wallpaper paste is always accompanied by the use of the entire area of \u200b\u200bthe room. Wallpaper sheets need to be lubricating the adhesive mixture, roll over the floor surface. If you do it on the laminate, it can be damaged or stain with glue.
  • After the wallpaper passes, you always need to close all windows and doors so that glue is good dry and wallpaper fixed on the wall qualitatively. At the same time, the humidity of the air rises in the room, such a microclimate can cause swelling.

It is best to get the wallpaper first, and then to lay a laminate.

What is first - laminate or doors?

Modern trends in the construction industry allow us to use high-quality materials and apply a variety of methods, methods, types of repair work. By purchasing materials, I want to use them efficiently. Therefore, the question arises that it is better to set the first: laminate or doors.

Some owners and master prefer to first install the door, shook out the slopes, and then lay the laminate. In this case, there will be several laminate panels near the doors.

There is a need to cut the door slope to substitute the laminate under it. It is very difficult to do this very hard, you need a special saw. Doors can be set first if they are made with a threshold.

If you shook the slopes in advance and carry out all the dusty work on the preparation of the doorway, you can safely lay the laminate. Door installation itself is not so dusty. In order not to damage the laminate, you will need to be displayed with its cardboard.

When the laminate is installed, you can accurately measure the height door canvas. In this case, the doors are smoothly and neatly installed on the surface of the laminate.

What is first - laminate or stretch ceiling?

Stretch ceiling and laminate - bright combination designer solution. But the question arises about the order of work on the installation of these elements, so as not to damage both types of material.

Settings Installation stretch ceiling associated with a sharp change temperature mode in room. Also, to install it, you need to use a stepladder, tools, heating appliances.

If the laminate is fastened to the installation of the stretch ceiling, it can lead to mechanical and temperature damage.

Anyway, repair work must be carried out from top to bottom. Therefore, the first is installed by the stretch ceiling, and then the laminate is already stacked.

If it happened that the laminate is already installed, it is necessary to protect it from the impact of mechanical factors:

  • Buttoning the entire surface of the laminate with a soft cloth, paper, or film.
  • On the perimeter of the installation of the stretch ceiling, under the stairs, you need to put a reinforced substrate from thick paper to eliminate the slide of the stairs on the surface of the laminate.
  • Under the used heaters for the installation process of the stretch ceiling, you must put wooden board or a piece of chipboard plate. This will prevent the laminate damage, in the case of random tipping of the heater.

Conducting any repair in the apartment is not such a simple task, and it requires careful planning. In addition to all other questions, one of the most significant is to determine what to do first is to glue the wallpaper or laying the laminate.

Stock Foto Room with cowed wallpaper and laminate floor

Of course, different repair brigades can solve this problem in different ways, since everyone has their own arguments and their own experience. Nevertheless, in our current article we will consider more than the advantages and disadvantages of each of these approaches. Based on them, we will try to reasonably and weigly answer the question of what is better to do first: laminate or wallpaper.

How best to do: pros and cons both ways

When you perform most of the work on the repair of the apartment, the task order is set according to the following criterion: how many debris, material residues and other pollution remains after conducting one or another stage.

When you put the laminate, the amount of garbage and pollution is minimized

In other words, experienced masters recommend first to install the material, when working with which there will be more garbage, dirt, and will also increase the likelihood of damage to those coatings that have already been established earlier.

Why first need to glue wallpaper, the main arguments

So, if you are trying to determine what it is necessary to mount first, wallpaper or laminate, it is necessary to carefully analyze all the circumstances. So, what should I consider:

  • When laying a laminate, there is almost no probability of the appearance of various contaminants. Naturally, it becomes possible in the condition that the preparation of the foundation of the floor was carried out in advance, even before you began to retain the laminated coating and carry out the bleach of the wallpaper.
  • Unlike some other floor coatings, such as carpet or linoleum, laminate should not be shorted next to the place of the floor compound with the wall, which eliminates the likelihood of damage to the wallpaper sheets.

However, all methods have both the reverse side. So, if you decide to punish the wallpaper after the laminate laying was performed, some of the types of this floor covering can be sufficiently sensitive to the effects of vapors that will be released when dried up the wallpaper glue.

For better protection of laminated coating during repair, it is advisable to use the usual film

The latter circumstance is explained by the fact that the drying of most types of modern wallpapers occurs in the absence of drafts and fresh air access.

In other words, the level of moisture, which increases during drying due to evaporation of the adhesive solution, will be quite high. It turns out that for quite a long time (sometimes up to several days) this humidity will affect. and on the state of the floor from the laminate, and if it is accurate - its outer layer.

On the other hand, a reservation should be done. If the blending of the wallpaper in the room with a laminate will be uniform, and not every year, then the negative effects of evaporation by glue will be reduced to almost zero.

Laminate before wallpaper: Is it possible to make it installation?

Consideration of the question of what needs to be done earlier, laminate or wallpaper will be incomplete if we do not mention such a situation when laminate laying is performed first. So, is it possible to lower the laminate until the wallpaper sticking? In fact, doing so - you can. Of course, the fact that poorly protected or at all unprotected floor surface will be damaged or the designer during the plating wallpaper is obvious.

If you started repair, then laying the laminate should be done later. The fact is that in this case the damage or dirt falling on the wall and wallpaper

At the same time, no one will prevent you from using a protective coating. In the role of this defense itself, everyone can perform a well-known polyethylene film, which reliably hides the surface of the laminate from the guaranteed garbage, glue and other extraneous waste characteristic of wallpaper gluing work.

At the same time, it is necessary to be extremely careful, since the legs of the chairs or the support of the room staircase, which you will use when repairing repair, can damage both the film itself, which reduces all efforts to protect the laminate coating.

Phased performance

As for the fact that it is still done first, wallpaper or laminate, in this respect there is a certain sequence that has been developed over long years on the basis of the experience of many qualified specialists.

If you started repair, then laying the laminate should be done later. The fact is that in this case the damage or dirt falling on the wall and wallpaper

So, the order of laying the floor covering and sticking the wallpaper layer should be approximately the following:

  1. First of all, it is necessary to prepare the working surface of the wall, even in the case of the subsequent blowing of liquid wallpaper.
  2. Then follows the stage of arrangement of the screed under the floor covering and preparation of the draft floor for the installation of the laminate.
  3. The next step is to stick wallpaper.
  4. Already at the end of the work on sticking, as well as after drying the adhesive composition, it is necessary to start retaining the laminated floor, as well as to install decorative plinths.

So, as a conclusion, you can note the following. Despite the fact that both methods have their advantages and disadvantages, still the best and most correct is the first: first putting the wallpaper, followed by a laminate installation stage. In any case, sticking wallpaper, and laying laminate belongs to the final decorative work, which must be carried out at the last stage of repairs in the apartment.

Be that as it may, unambiguously say that correctly, and what is not - it is impossible. Everyone in the repair process arises their circumstances, which sometimes have to adapt. That is why the owners of the house or apartment, which produces repair, should thoroughly analyze circumstances and already on the basis of certain conclusions to make a decision on what to do first: laying a laminate or glue wallpaper. In any case, we wish you a good repair!

The usual owner of the apartment makes repairs at home infrequently - about once every five years. When the work planning begins, the question of the sequence of facing is often raised. What to do first: mount the floors, install doors or glue the wallpaper, because I want to do everything right and efficiently. Is it threatening a change in finishing order with difficulties and critical errors? Specialists of the finishers have an accurate answer to this question.

What is first: shook wallpaper or floor mounting

Wallpapers are glued under painting or with a finished pattern and color decision. Parquet or its more affordable imitation is laid on the floor - laminate. In the kitchen, in the hallway and in the bathroom, a successful solution will be laying tiles. Experienced masters It is recommended to start repairs from the preparatory measures for alignment and primer walls in front of the finish coating. On the floor, the black base is a screed, and for thin alignment and finishing finishing, self-elevated composition is poured.

Pre-alignment of floors will prevent the creaking of parquet or laminate

The question of what to do first - the floor or door is unequivocal to the work in the process of doing. After filling the floor, installation door box and canvas then mounting foam Fill the gaps and plaster the formed slopes. Only after installing doors you can calculate the width of the strips around door Piece And accurately lay out damper gaps when laying the finishing flooring. Thresholds and plinths are mounted at the end of the repair.

If you install the doors after finishing floors, laminate or parquet must be protected from damage by multiple layers of industrial cardboard.

When the walls and floor are smooth and dry, and the doors are installed, you can go to finish finish. According to the rules, the wallpaper is glued first, such an order has several advantages and avoids difficulties in the process:

  • wallpapers are reusable on the floor with a stationery knife, and if the laminate is already laid, you can scratch it;
  • application of glue and paint is impossible without "flap" and spots on the floor;
  • under the ceiling work on a stepladder, which scratches and rubs the new floor, presses on him;
  • laying the laminate occurs without glue and other liquid or dirty substances, so the risk of blurred wallpaper is minimal.

After laying the floors, spending the walls so that dust remains on the wallpaper.

If an inexperienced master is forced to mount the laminate first, and then glue the wallpaper, then subject to the following tips to avoid errors:

  • choose a laminate should be a high class of wear resistance, then mechanical loads and scratches are not terrible to him;
  • to increased humidity When the wallpaper is drying, it has not led to a swolver of the floor covering, it should be closed with a dense polyethylene film, it will protect both the glue and paint stains.

At the end, with any chosen manner, the installation of the plinth is in the perimeter of the room, it will hide the lower edge of the wallpaper and the technological clearance of laminate or parquet.

Usually, the plinth is chosen under the color of the floors, but different options are possible.

In theory, you can shove wallpaper before installing the floor or after that. Both options are fully fulfilled, and the difficulties can be smoothed with the help of remedies. However, the first way is more rational and practical, it is cheaper and requires less time and labor costs. Doors are better installed after the black floor finish, but before sticking the wallpaper.