We offer to buy a parquet board from the manufacturer, which we create at your own factory in Podolsk and the Krasnodar Territory. Our HOFPARKETT floor covering is high quality, durability and beautiful designcorresponding to timely trends.
We offer to buy a parquet board cheaply, while guaranteeing decent quality. The loyal cost of flooring is ensured by optimizing the production and the absence of costs for the delivery of products from abroad. Our plants are in Russia.
We present various collection of parquet boards, among which there are solutions for registration and classical and modern interior.
We use environmentally friendly oak wood grown in the Caucasus. Through the use of modern Italian and German technologies, the picture of the spike is profitably revealed.
High-quality wood drying for an apartment parquet board is performed with optimal humidity, which provides a long operational resource. Our products are well adapted to domestic operating conditions. For example, the sharp shifts of the microclimate indoor.
Production occurs in automatic mode. Manually we only constitute wood, which gives the flooring a special charm. On our site parquet board you will find beautiful models For their interior
Stages of production:
With wood harvesting, we apply high selection cutters. Therefore, our parquet board from the manufacturer has worthy quality.
Among the cutters that we use:
Natur and Rustic - tangential cut, as well as the inclusion of a minimum of alive bitch. Collot, cracks, wormochin, no chips. Production marriage is unacceptable. The cutters are carefully selected at the drying stage. Inappropriate standard are excluded from further use.
Chamber drying is performed in special equipment 12 days. In the future, the required condition and moisture level of the cutter are obtained using atmospheric drying.
Wood dried to ideal parameters with a chamfer and subject to competent installation, a beautiful and reliable product.
We offer a parquet board without chamfers and with her.
To create parquet, we apply only endemics - ash and oak, which have high performance characteristics. The initial quality of wood and the correct drying provide minimal deviations on the residual internal voltage of the product and humidity, which indicates the compliance of international standards. Quality control is observed at each stage of production.
Lamins have a thickness of 15 mm, while the thickness of the useful layer reaches 3.5 mm. Thus, you can perform up to 3-cycles.
We can buy a parquet board cheap in Moscow. Diversity design solutions Let it be possible to select an option for individual design.
Phanaged layer We produce from birch - affordable, but stable breed. High-quality sizing, as well as drying layers guarantee their reliable clutch and stability of wood to the oscillations of the microclimate indoor.
For a beautiful appearance of floor covering and disguise, admissible seasonal allen, we apply the following types of micro:
On the official website, parquet board shows high quality and perfect geometry, which highlights our floor covering among competitors.
When painting wood, modern straight-colorful equipment is used, as well as a competent approach to the selection color palette. Our specialists take into account fashion trends and sought-after colors. In addition, we work on the creation of unique non-standard colors.
In our warehouse, parquet board is in different options shades.
The finish coating has 5-7 layers. For finish coat We use lacquer or German oil. This ensures maximum wear resistance of the product. Oil or varnish boards dried in the chamber under the influence of UV radiation.
The connection of the type of spike-groove ensures a dense assembly without cracks and gaps. Due to the accuracy of the creation of dies according to GOST, when installing, the flooring demonstrates monolith.
In addition, our parquet board on the warm floor saves its characteristics and serves a long time.
Superproof elastic adhesives are used for the production of products. They have high indicators of environmental friendliness and durability. Thanks to this, the board is punctured by such adhesives withstands 25 years of use in the conditions of changeable microclimate. The layers are glued according to cold pressing technology. This makes it possible to exclude strain.
We offer to buy a parquet board inexhamable: length - 400-1800 mm, width - 150 mm. Various slats length expands the ability to organize different designs Outdoor coating.
To create an outdoor cover, we use German equipment.
If you want to purchase products at a bargain price, then we often use the sale of a parquet board in Moscow, where the cost can be lower to 50% or more.
According to the Russian standard, the goods correspond to GOST 862.3.86 - "Parquet products. Parquet Boards »
For the German standard, the product corresponds to EN 13489 - "Multilayer parquet elements".
The goods are made in Russia, german technology And on high-quality German equipment.
GOST HOFPARKETT Certificate
Download file - PDF format
HOFPARKETT expert opinion
Download file - PDF format
With proper manufacturing, parquet can be the most beautiful, natural and reliable flooring. But, unfortunately, not every parquet is equally good. The quality of the parquet depends not only on the quality of the materials used, but also on the characteristics technological process production. Parquet make approximately one technological schemeBut each manufacturer uses its recipes and know-how in the production, which ultimately determine the quality level of the produced parquet.
As can be seen from this technological process, the deck board (piece parquet) is relatively simple. The production technology of the parquet board is much more complicated, because the multilayer parquet board is a whole construction consisting of three layers of various wood glued together. As a rule, in such a design, low value tree species are used to create a substrate, and valuable - to create a facial layer. From the features of the technology of the production of parquet board, the correct selection of wood, its condition, the type of glue and varnish will depend on its reliability, durability and aesthetic appearance.
1. Creating the front layer of the parquet board:
a. A cutting board of valuable wood on a sawtop is cut on the planks of the specified dimensions (lamella).
b. Boards are treated on a milling machine to obtain the necessary geometric proportions and the necessary cleanliness of the surface.
from. The lamellas are wedged with glue and glue the top front layer of the parquet board from them.
d. Depending on the desired type of surface of the facial layer, brash, planing, whitening, heat treatment and chamfering.
2. Creating a parquet board substrate:
a. Cutting board from low-value tree species, usually from coniferous rocksThe sawmaker is cut on the planks of the specified sizes to form a 2nd layer.
b. The third layer is a solid cloth from a veneer of coniferous species of trees, and is designed to stabilize the entire three-layer construction.
from. The obtained boards are treated on a milling machine to obtain the necessary geometric proportions and the necessary cleanliness of the surface.
3. Shakeling of flooring board:
a. On the front layer of the parquet board, the 2nd layer boards are glued transversely.
b. In the second layer on the milling machine, a castle connection of spikes and a groove is formed or a rotary-angular lock.
c. The third layer canvas is glued to the second so that the wood fibers of these layers are mutually perpendicular.
The principle of segment (lamella) design allows you to achieve high stability of the parquet board. The perpendicular location of the layers gives parquet board significant strength, resistance to temperature drops and changes in humidity levels. A parquet board of such a design was invented and created by Gustav, in 1941 in Kahrs, which to this day makes the best parquet board in the world.
1. The quality of the Kahrs Parquet Board is achieved at the expense of a scrupulous approach to each stage of creating a board, the production of the production process, compliance with the traditions of production formed for 150 years of the company's existence.
2. The process of production of the Kahrs parquet board begins with careful selection of raw materials. The trees cut down strictly at a certain time of the year, not looking at the ever-increasing needs of the market. Then, at the factory, there is a strict chipping of wood that does not meet the highest requirements.
3. No less important in the manufacture of parquet Right drying of wood. Before the tree falls into the drying chambers, it will be dried naturally in the open air for six months, if necessary and longer. This aspect significantly distinguishes Kahrs from all other parquet board manufacturers.
4. To glue all three layers of the parquet board, the highest quality adhesives are used. The Kahrs plant uses pigmented adhesive with the addition of special dyes intended for visual control of the uniformity of its application.
5. A significant role in the creation of a beautiful aesthetic species of parquet is played by Kahrs, which also serves as a protective coating that protects the board from the effects of moisture and light mechanical impacts. Kahrs lacquer is the most beautiful and pleasant eye. It does not swear, but in contrast in every way emphasizes the natural beauty of the tree.
6. The last and important stage in the process of creating parquet Kahrs is quality control. Each board is viewed at different angles, with a special lighting with two employees working for no more than 2 hours a day in this area. Any visual deviation from the norm is immediately studied immediately, including a tactile way.
7. A serious and very important difference in the production of parquet Kahrs is that almost the entire process, starting with the processing of a rounder and ending with the packaging of the finished parquet runs in the shops of one plant under full and thorough control of specialists. Many other floorboard manufacturers are forced to use ready-made blanks purchased from various suppliers. Thus, the cycle of their production is far incomplete, and it is very difficult to talk about full quality control on their part.
Forest cutting during a certain period of time, natural drying outdoors, durable glue, beautiful lacquer, emphasizing the naturalness of the parquet board, strict control of production and attention at each stage of production - these are the distinctive features of manufacturing technology, which make it so natural, strong and durable .
So, the technology of production of a parquet board in general is the same in all enterprises, but differences can be used to use different materials, sequences of manufacturing stages, processing methods and a total of a manufacturer to the process of creating a parquet board - from them mostly dependent on the quality of the produced parquet floor. If a person belongs to his work with love and attention, as it makes Kahrs, then the result is simply obliged to exceed all the expectations.
Clearly realizing that natural parquet is solid advantages, do not everyone know what stages the material passes until the moment of readiness. What is the production of parquet, what equipment is used for this and how much the production of parquet board differs from the manufacturing technology of piece material? About this below.
Both parquet and parquet board are produced in several stages. The first is the manufacture, the second is quality control. In the control process, a visual inspection of the material is performed, additional devices are used.
Both manufacturing parquet and more budget option - Parquet board implies the use of natural wood species. Traditionally - this is:
Of exotic breeds, the most commonly used:
The feature of exotic tree species is improved performance characteristics. Many breeds are better coping with temperature leaks, more resistant to moisture.
The palm of the championship with a piece parquet shares mosaic, followed by a panel and parquet board. Traditional material dimensions: Thickness - from 1.5 to 2.2 cm, length - from 9.5 to 50 cm, width - from 3 to 15 cm.
Start the process of manufacturing material for finishing floor from drying and sorting components. Raw materials comes to production in the form of blanks packed in pallets. At this stage, a thorough inspection of the material is carried out for the availability of visual defects. If any, the material is not used.
High-quality raw materials are selected and dried. To do this, use drying chambers where the workpieces under the influence high temperatures Leave for several months. At the same stage, thermal processing of the material is carried out - heating it without air access with subsequent natural cooling. The result of all carried out manipulations is becoming a dense and reliable wood, not prone to deformation.
The next stage - sawed the prepared wood on the boards with certain parameters with the removal of defective sites. Using milling machines, the obtained parts are processed from all sides in order to obtain parts of the correct geometric shape and the facial surface prepared. These same machines are suitable for cutting on the elements of the future parquet ridge and groove. Finished boards pack for further implementation.
It can be noted that the manufacturing technology of a piece parquet is not the most difficult, especially if you compare it with the production technology of a parquet board. Complex design of multilayer elements from different breeds Wood imposes a certain imprint on the process of obtaining, obliging manufacturers to adhere to the installed algorithm.
For the manufacture of a modern parquet board, they use both expensive natural wood species and less valuable - for the substrate device. From the peculiarity of the production process, the choice of wood for the material, its state, type of glue will depend appearance, operational properties and service life of the future coverage.
So, the production of the parquet board consists of the following steps:
At the initial stage, using a saw blade from valuable wood, wood cuts into the lamellas of the desired parameters. Next, they are treated with milling machine, seeking products of correct geometric shapes. Laminers are lubricated with adhesive compositions, getting the front layer, after which, depending on the desired result, thermal processing, whitening or planing is carried out.
To create a substrate edged board from inexpensive wood, more often coniferous, saw. Third layer - veneer cloth coniferous trees Designed to stabilize the design. The finished boards are treated with a milling machine, receiving products with proper geometric proportions and a clean surface.
The final stage is the fixation of the layers of the board, when the facial part is glued with two others. The second layer is equipped with a locking of the groove of the groove or a swivel-angular type lock. The second and third part of the board glued in such a way that the fibers formed mutually perpendicular planes. This method of compound increases the strength characteristics of the product, including in conditions of sharp jumps of temperature and changes in the humidity level.
To establish a process, it will take socialized equipment for the production of parquet or parquet board. Most important cars:
In addition to the equipment for the production of parquet, you need to consider the location and arrangement of the room where work will be held. To begin with, there will be enough room with an area of \u200b\u200b200 square meters.
If there is no possibility to place all the equipment in the room, part of it is located beyond it, for example, a sawmill area can be placed outside the borders of the workshop, handling the canopy. And for the warehouse, there is no canopy.
The cost of the square meter of the Parquet consists of 60% of raw materials, by 15% of electricity costs. The rest is the cost of paying for employees. In general, the profitability of the Parquet business is at least 15%.
To avoid difficulties with the arrangement of the room for working with natural wood, it makes sense to start production in a special workshop equipped for wood processing taking into account fireproof norms.
And last by purchasing raw materials for the manufacture of parquet from natural tree (Usually out of oak and ash), it is worth remembering the documents confirming its quality. Mandatory workpiece should come with radiation safety certificates and hygienic conclusion of the Ministry of Health. Only certified raw materials makes it possible to obtain a certified parquet.
In conclusion, we note that the technology of the production of a parquet board and a piece parquet is almost every manufacturer identical. The differences are, but only in the sequence of steps and processing methods. The relationship of manufacturers to the production process of material with control or its absence at each stage is also distinguished.
The company Parquet Fashion has its own production. Production is equipped with the most advanced equipment in the area outdoor coatings. We work more than 120 breeds - both traditional and rare and exotic. All wood passes a multistage selection, sorted between sizes and selection, thank what the high quality of the modular and artistic parquet is achieved. Our production is focused on the manufacture of an exclusive parquet, wall panels, window sills, countertops, caisson ceilings, stairs. We make products on the full cycle - from the forest harvesting to the release of the elements ready for installation.
In our work we use only specialized high-precision German and Italian machines, as well as manual work when creating the most complex forms of modules and drawings. Not to compare with the level and quality of the product made by masters in manual.
Parquet processing equipment that we use:
§ Automated paint UV "Cefla" line Italy, for more precise and clean parquet painting (parquet array, piece parquet, engineering parquet, parquet board). Lacquer or oil applied by such a line is cured due to the impact on it of ultraviolet radiation in a very short time. One of the advantages, such coatings, is their sustainability for sunlight, the coating is not fade longer and keeping the original color in the sun.
§ Machines - CNC "Griggio" Italy (machine tools with numeric software control) and a vacuum table that provide high-precision production of complex curvilinear fragments of the patterns of modular and artistic parquet. By ensuring the accuracy of the product to the tenths of the millimeter. These machines allow us to create real masterpieces of wood. To date, we make outlets (artistic floor parquet) up to 3 meters in diameter.
§ Brachware "Schroeder" (Germany), "Griggio" Italy - are used to create an additional relief on the working surface of the parquet. Using metal brushes are selected (removed) soft fibers of wood, leaving the most durable, thereby manifests the texture and pattern of wood, What emphasizes its beauty. The depth of the brush Customer can be adjusted at will.
§ Machines for the Taste "Costa" Italy is one of the latest news of carpet processing. With the help of the shafts on which a certain drawing is applied, ride the harvesting under the pressure of the heating shaft, having received its imprint on the parquet in the form of a non-interrupted volumetric pattern. With this technology and subsequent painting, such 3D effects are achieved (the floor looks in bulk), as well as the effects of aging.
§ Machine for manual bracket, this effect is called wave
We manufacture art and modular parquet in variants of massive and engineering design using GRIGGIO (Italy), Weinig (Germany). Modules are produced by gluing along the ends, followed by crunch and calibration of the module, this allows you to achieve perfect geometry. Production of solid modules wooden barIt allows you to significantly increase the service life of the module, and allows its restoration and recovery for the period up to 20-50 years. Parquet Fashion Modules can be encrusted various elements: metal, composite materials, colored resins, marble, cork, leather, stone, Swarovski rhinestones and other elements.
Our production Parquet Fashion has its own collar selection atelier for the customer. Painting we can produce as on automated line So in manual, which makes the product more unique and individual. The color selection service includes trial cuts, determination of the necessary sizes, determining the material and type of construction. Recently, the effects of aging (vintage parquet) are gaining its popularity, as well as patination, manual healing. We apply this type of treatments in manual, creating a unique unique relief on the floor.
Finished products are carefully packed in a special way to exclude mechanical damage during transport. We guarantee high quality products. We hope you will appreciate our opportunities and our willingness to do your job quality.
Today there is a reason to argue that the production of parquet is one of those types of business, which is successful not developing in the center, namely in the regions of Russia.
Evidence said are two Russian leaders of parquet production - the Obninsky zd and the Zarya factory, located in the Kaluga region. The existence of numerous Russian trademarks Parquet reflects the growth trend of the commercial attractiveness of this business, imagine their incomplete list: ALLORO, JUNGLEWOOD, "Adygea-Parquet", "Art Parquet" Amber strand "," Bond "," Maykop Parquet "," Parquet Romanovsky "," Old master"," Traditions of the Russian Parquet. "
The main consumer of the parquet is the construction industry. It is also important to cooperate with housekeeping stores, and especially with supermarkets. The survey conducted by the magazine "House and Genua" showed that 75% of the developers of Russia's developers feel the deficit of the supply of high-quality parquet. Parquet production technology progresses that it just demonstrates the above-mentioned bouquet of various brands.
Entrepreneur, before entering a business for the production of parquet, must simultaneously take into account and link several important factors among themselves.
Technical issues are extremely important. Nearby should function logging enterprises or sawmills and, of course, grow in industrial volumes of wood used for the production of parquet.
An uninterrupted transmission of electricity should be provided (perfect - of two alternative power transmission lines). The preliminary agreements on the purchases of products with developers (SMU, OTH, etc.).
To minimize possible risks in the exercise of production, a small woodworking plant on the outskirts of the city is becoming the optimal step on the outskirts of the city. There in specially equipped production room, Equipment is installed for the production of parquet board. (While initially the business project itself provides for organizational and technical requirements controlling organs.)
The placement of production should obey the procedure for the implementation of the production process. The convenient driveway to the sawmill is important. For a sawmill, an area of \u200b\u200b50-100 m 2 is given, a canopy is equipped over it. The roughboard - sawmill production - is stored nearby to the preparatory site, which in the room there is a production area of \u200b\u200babout 90 m 2. For the final stage - "finishing", carried out using a parquet line, will need 60 m 2. Thus, the total estimated area under the production of parquet is about 200 m 2.
According to statistics, the production of parquet is "on the rise". A peculiar psychological incentive of further development, as specialists noted, is the predominance of the goods of a low level of quality in the market of Russia (as well as other CIS countries). Entrepreneurs, opening a parquet business, seek to demonstrate a higher quality of their products. Therefore, the prospect of commercial success may even have small production, launched the production of goods users.
Production of what parquet is advisable to develop? We will follow from the most sought-after, then first it will be positioned piece, behind it - mosaic, then - parquet board (multi-layered) and, finally, shield. Multilayer parquet requires additional investment in adhesive production. Of course, you are preferable to use imported machines for the production of parquet.
Still, most Russian entrepreneurs produce a piece parquet. It is standard technological texture planks, usually manufactured in the range of thickness 1.5-2.2 cm, 3-15 cm widths, length 9.5-50 cm. How is it classified? Everyone knows the classic, usual "Soviet" format - 15 x 45 x 250 mm, the rest is considered to be a European bar. Parquetins are rigidly mounted with each other with the connection of two side tuning with two grooves.
Each entrepreneur, manufacturing parquet, focuses on a certain market and, accordingly, selects industrial raw materials under its requests. It is well known that the texture of any parquet coating and its drawing depends on the type of wood. Creative approach to the choice of tree varieties requires the production of art parquet.
Let us give an example of some types of parquet (depending on the used raw materials). Oak parquet, probably most popular in Europe, possibly due to the historical tradition. Oak Exprove is considered to be an embodiment of strength and fortress, perhaps, therefore, products from it traditionally enjoy special demand. Among the products from the wood of moderate latitudes is one of the most durable. The color may be different: from light brown to dark noble shades of the moraine oak (the most expensive). 
Parquet from beech is weakly textured, however, it has a delicate warm light pattern: from whitish with a yellowish tinge to saturated golden brown. Nevertheless, its wood appreciates along with the oak. Real connoisseurs of parquet - British.
It is noteworthy that with additional steam processing, this wood acquires a reddish color. (Parquet production sometimes uses this method.) The wonderful parquet of ash is also obtained. In addition, it is no less durable than the oak, it is inherent in a thin factory figure. Pepling, with a reddish tint of walnut wood capable, being turned into a parquet, create on the floor, thanks to his bright pattern, really fantastic panels. The bright parquet of birch is also popular.
The manufacture of a full-cycle parquet includes several stages.
First, the primary processing of the forest is underway with the help of a sawmill (the cost of Russian - 50 thousand $) and dryers (respectively - 15-20 thousand $).
Then - Preparatory Stage. Within its framework - with the help of a multiple machine (5-15 thousand $), the thickness of the product is set. The main processing is made on a four-sided rignery machine (12-15 thousand $) and continued (2-4 thousand $), the cutting profiled board to standard "pieces".
And finally, a parquet line equipped with a planing four-sided machine combined with Sipiospise ($ 60,000 (from the Russian manufacturer) to 220 thousand $ - imported).
If the entrepreneur seeks to organize the production of parquet, competitive on the foreign market, then he should be guided by ISO9001 and DIN standards. It will take at least an imported equipment at least at the final stage of the production process. At the same time, investments in the production of products will be 500 thousand $. Is it worth mentioning that improving product quality should stimulate the work of labor?
The production of a full cycle, serviced by Russian manufacturers, will cost cheaper - at $ 250 thousand. It will correspond to Russian guests and focused on the Russian market.
The production of art parquet in Russia began in the XVIII century, when the St. Petersburg palaces were erected. Masters of that time used more than 50 types of wood. Modern industrial production is based on sticking color planks on the base (the so-called Marquetry technique).
In the manufacture of such a parquet, wood layers fall on the base perpendicular to each other. In such a combination, the texture of their fibers looks the most advantageous. The front layer is made of high-grade wood with a thickness of 5-6 mm. Such a product is painted, usually in 5 layers.
An entrepreneur, "trying on himself" any business, comes from the required amount of investment in it. The costs for the production of a piece parquet when buying prepared raw materials can be $ 50 thousand.
At the same time, the entrepreneur selectively buys parquet machines: parquet line russian production The cost of 20 thousand $, and also equips the preparatory plot that at least 20 thousand $ will be at the minimum. Purchase, installation, launch of equipment, as well as the cost of purchasing raw materials, will be just mentioned above 50 thousand $.
However, the entrepreneur-production does not stop at this acquisition. Pickup this economy of the "launch" of the business, it continues to invest in production, striving to organize its full cycle.
We should not forget the old truth - "the frames decide everything." Initially, you should hire reliable assistants: a competent accountant economist, a technologist and a marketer driver.
Without an accountant-producer also can not do. After all, in addition to the production points, you will need to issue a lot of documents: labor contracts, labor regulations, staffing, personal cards, accounting books, registration of orders.
"Strong" technologist is also a guarantee of business success. After all, the production must be adjusted according to DSTU 3819-98 and GOST 862.1-85 and DSTU 3819-98, regulating production tolerances, curvature and purity of processing, permitted level of defects.
The field of activity of the marketer driver is to study the market, conclusion of contracts with suppliers, delivery of raw materials and sending finished products, carrying out its sales.
Priorities in the selection of workers are their ability to work on equipment, and if necessary, they should be able to repair and adjust the machine for the manufacture of parquet. It is also important for the overall health level of workers, because they, in addition to the main work, it is necessary to produce loading, unloading, storage.
In percentage ratio, parquet production costs are as follows: 60% - the cost of raw materials, 15% - payment of electricity and other energy carriers, 20% - wage personnel. The rhythmic work of production is important, its full loading, no downtime and soldering. Equipment for the manufacture of parquet should work without downtime. In compliance with these conditions, the profitability of the Parquet business is 15%.
However, entrepreneurs do not stop at this, further increasing profitability due to the implementation of the full production cycle: from the fence of the forest before laying the parquet. After all, the sale of parquet, combined with its laying, increases its retail price by 2.2 times. The correctness of the masonry of the parquet requires qualifications. The production enterprises developed this direction also have a brigade of builders who carry out the flooring of the parquet.
Parquet production is a living, creative process.
It is linked between many factors. Production process and accounting, rhythmic work with suppliers and product buyers, labor productivity, product quality.
The achieved level of production is directly proportional to business profitability. So, the square meter of a high-quality imported parquet costs $ 100, and the "Hermitage class", which demonstrates the production of art parquet - $ 300.
Well, of course, the ideal way for business entrepreneurs to optimize demand is to cooperate with network construction stores.
