Often in many well-groomed courtyards there are interesting homemade sceners, and swan from a tire deserves special attention.
Step-by-step instructions for creating it, of course, is, but you need a certain skill.
In fact, these creative processes are not so difficult, the main thing to get required materials, tools and follow the right creative algorithm.
So, for this creative case you will need:
Of course, the key elements here are old tires. It is best to use almost bald rubber, that is, thoroughly worn tires. It is much easier to work with them. Application here is not allowed here.
An excellent option is a tire having a caproine reinforcement. It will greatly facilitate work and make it possible to make the subsequent use of the shape created safe.
A product having a metal cord is very difficult in processing and leads to small but frequent cuts.
If you have no tire in your presence, you can contact the nearest tire. To create a conceived swan, there is a single tire, although it is better to take two more pieces for a reserve and some experiments.
Before cutting and cutting the tires are thoroughly washed and dried. These operations are best carried out in the fresh air.
First ensure yourself a complete arsenal required tools and materials, then not to be distracted from work. With certain skills, the planned figure can be created in one day.
The outcome appearance of the figure depends on the markup scheme. If you make cuts without errors, then turn it out the tire will be significantly easier. Usually the basis here is R13 rubber. Its circle in the aggregate is 180 cm.
The middle of the tire is indicated by chalk. A significant part of the circle is given to the neck and beak. Standard Swan Parameters are as follows:
The main stages of cutting the planned figure are reduced to such operations:
It is necessary to start to paint the tire on the contours of the head and neck. You should not pay more attention to one side of the figure. Otherwise, cut the opposite side will be much more complicated. Best of all alternately cut both sides.
So that the billet of the swan had the desired volume, it should be put on the ground down the already cut side and pull the side components upwards. The central side you need to hold the foot. These operations are very laborious.
On the sides there are half rings. They mimic the wings of the bird being created. They must be lowered down. 
For metal reinforcement, tires will need additional processing using the grinder.
At the same time, it is possible to be seriously injured from the emerging fittings. For this reason, creation from such tires are arranged on the site only as a scenery. For playground The appropriate option is the creation of a tire with a piping cord.
Bird's neck is required. So your covered swan will be more hiking on the present. Here you should act in this method:
For future eyes, your swan can use rubber pieces. They are attached screws.
On the side of the tires are notched. This is an imitation of the plumage of the conceived swan.
Your swan you can make a fabulous character, thereby make a special charm in the design of your site. Swan can be crowned. A plastic bottle or tin can is suitable for creating a crown.
Thanks to such an operation, the look of swan is obtained elegant and aesthetic. You can use classic white tones, and you can act original and introduce silver and gold shades.
A black swans are very mysterious and gracefully look. The performance of high-quality color is possible any paint suitable for external work.
For Swan from tires better apply enamel, oil paints or nitrocracy. Not rarely for these purposes is used aerosol automotive paint.
The main criteria for the working surface before painting: cleanliness and dryness. Applying the main layer, you can decorate the figures with acrylic materials. The more natural appearance of the figure can be given if you arrange a plumage on it and an across your head with a beak.
Placing the figure is also an important question. If it is put in the parisader near the entrance, the stand is organized for it. Stand serves the second tire. It is painted in blue (imitation of water).
This sculpture can easily turn into small flowerbed: Just inside the tire is embanked by the earth, flowers are planted, not capricious in care.
In the country area optimally arrange a more complex decor. As you know, swans dwell on reservoirs. Therefore, for your figure it is useful to create a small pond. His creation is nothing complicated.
You need to dug a small kitty. Fill it with a film. To press her edges, and at the bottom lay out pebbles.
You can simulate water from the tire. Select a small zone. Pour small stones there. Color them under the color of water, for example in a blue color.
It is possible to surround the design with green plantings. So only intensify decorative effect Created bird.
Today, full of variants of decorative figures created from the tires. These are swans, and exotic, and other birds, as well as animals. Much depends on your fantasy, skill and hard work.
Warming Option Win from Tires See next video:
I live in the village in New Moscow. Most of all, our settlement is similar to a large construction site, in some places we have roads, and we have no improvement in the landscaping. That is, all the way that the eye in Moscow does not notice, all these flowerms, lawns and even sidewalks, we do not have. But we also want.
I somehow go from the stop and look, and the entrance to our village is decorated with six car tires. Our administrator could no longer look at a solid liquid clay, in which our village is being immersed, and decided to put beautiful flower beds, from tires, and then put the flowers in the tires. I go swear. We, I say, autocolonna, bus park, from what fright do we decorate yourself with tires?
The administrator looks at me and does not understand. And he says that if you paint white paint and bury, it will be beautiful. What, they say, the neighbors past pass and all approve the initiative.
And then I understand that "beautifully" all different and I don't need to argue. From my point of view, this is a pound poverty, all these flower beds from the painted tires, but explain to someone who considers it normal, I will not take it. Laborious.
If you go through our surroundings, you can collect a large collection of this "beautifully".
I see bird feeders made from dairy packages. Someone made a mini-greenhouse from a five-liter plastic bottle, with a cropped bottom, and someone spoiled a gason with a multi-colored fence from the covered plastic bottles from under the sod. But the star of the garden architecture is a swan carved from the tire.
And so I think guys, why don't you bring this garbage on the garbage and do not make a birdhouse from the tree, and the fence from the stakenik?
And the flowerbed can still be upset or make a woven from real branches, you know about this?
Probably I think, people do it out of savings. And I ask in the search engine "Klumba from tires." The search engine corrects me: "Tire beds". And a hundred recipes falls on me how to make a beautiful composition from unnecessary summer rubber.
"Every owner country house It seeks to decorate the area adjacent to it. The purchase of industrial vases from concrete or plastic modules quickly solves this problem, but is accompanied by serious costs. In order to save it, you can use step by step leadership To create such a simple product like a flower bed of a tires with your own hands: Floor clubs from wheeled tires and practical recommendations They will help to navigate in this matter. "
I have a question guys, and you, adorning the plot of tires, here you are built on what? Did you find money for him? Why exactly on the flower beds suddenly need to save?
Don't create from garbage, you do not process it for humanity, you just take the garbage and throw it out
Big terracotta clay pot, twice the top of the tire, cost me a thousand rubles. We agreed that I would buy several such pots in the village, and the administrator would throw off his tires and I would never see them again. This is if about my personal history and village.
Well, in short, everyone who is in such a rubbish planting flowers, is it that, wisely spends every thousand rubles? Now we will not talk about pensioners, and let's talk about all the strong and normally earning men and women who did not find 100 rubles for a small plywood birdhouse and 50 rubles for a film for greenhouses, and watered in their yard a package from the milk and a plastic bottle. I just want to say that the savings have nothing to do with it.
People do not make it out of savings, but because they believe that it is so normal to live. Because they have, regardless of the level of income, in the head of poverty. Because this aunt or uncle simply cannot imagine how they go and buy something for their money. They are better than something from the garbage package and will make "beautifully". And money equivalent to normal flower bed, they will eat better or cigarette on them.
Well, the reigning near the Nishchebrovsky standard also take into account let. There are so many attempts to make a candy from shit, we have it "do it yourself", so many rubber swans that it seems that this is our norm.
I even met on the Internet a whole guide called "Create from garbage". Canning bank turns into a casket, a DVD in a clamp for curtains, but a rug from garbage bags and a decoration of an apartment from egg trays. If you think it's all the authors came beautifully, no, ugly. Just for some reason, people are very difficult to make a simple thing. Take and throw away the garbage, get rid of tires and send old discs and packaging from the eggs into the trash can.
Do not create from the garbage, you do not create innovation and do not process it for humanity, you just take the garbage and throw it away.
For those people who appreciate beauty, there are many ways to decorate the space around yourself, whether workplace, parisader, apartment or playground in front of the house. For example, you can use old tires from the car as a small flowerbed or to create different figures. Very often you can see how the swan or other animals made from old tires are banging before the private house. The tire can serve as flower flower - such an application of old tires can be seen in the courtyards of high-rise buildings and on the playgrounds of kindergartens.
Step-by-step instructions will help make a swan from unnecessary tires, and even if it does not work from the first time, it is not necessary to get upset: it is a rather painstaking job. First you need to find a tire, which will be most convenient to use. For such a task, any "bald" tire, which has a longitudinal drawing. It will be better cutting, and make it easier to make it easier. Before starting work, you need to wash and dry so that it is easier to work with it.
So, on the tire you need to put the line with chalk, which will be divided into in half, the lines must be parallel to each other. With this action, the image of the neck of the swan is created. After that, you need to draw the beak, which will go from the first axial line, the length of it must be no more than 9 cm. Next, the beak should go to the head of the swan, its length is about 12 cm, the width is up to 8 cm. Below the head begins the neck, first she It has a width of 5 cm, and closer to the body it expands to 10 cm.
The tail is made using two parallel lines that have an 8 cm width, and a length of about 30 cm. The tail of the tail is the result after cutting the beak, so the tail is made easier. After all the elements of the Swan are drawn, you need to move to cutting, for such a process you need to get gloves and points.
For swan clippings, you can use a grinder if the tire is rather solid, but after all the main lines are cut, it is better to use the electric jigsaw. Move the grinder is better on two lines immediately, making cutouts of 5-6 cm on each of them, so the process will accelerate, and will be easier. If you cut first one side, and then another, the process will be longer. After all the elements are cut, they need to be poured around the edges so that there are no sharp or ribbon sites.
In order for the swan to gain the wings, the swing of which is pretty large, the tire must be turned inside out, for this it is necessary to make the effort of legs and hands at the same time.
To strengthen the neck and head you need to use steel rods. To do this, it is necessary to drill paired holes on the axial line on the axial line, the distance between which will be at least 15 cm. You need to drill from the head and to the tail, and then in each hole to turn a soft wire into each hole. With her, rubber is attached to the metal bar, and the swan acquires a clear silhouette.
The rod is better to lay, starting with the bottom of the swan, thereby you can twist the ends of the soft wire around it. After the neck is attached, it needs to be taken before receiving the bend of the present swan.
In principle, the swan figure is ready, now you need to paint it, even if the swan is black. But before the painting swan, it is necessary to examine on the subject of sharp or uneven elements so that neither the children nor adults could be injured.
Bird can be painted in white or black, depending on the desire of the owner. Be sure to highlight the beak bright color, for example, red or orange. The main thing is that the paint, which is painted swan, was standing, because it will be constantly on the street.
You can also make a swan, painting the specks black, or using large nails for this. Color gamut You can choose at your discretion, do not necessarily use white or black color.
Such a scheme for the manufacture of rubber swan is considered the easiest, so you can not look for other options. And for a visual explanation of each step, you can watch training videos, and, following the example, do your swan.
Also, the swan can be put in different places, for example, near a flower or in the garden, in front of the yard or, directly, in the yard itself. As a stand, you can use another whole tire or sand.
In any case, such a way to decorate the yard will like many: and family members, children, and even animals.
Swan from tired - Cheap version of the decoration of your site. Unnecessary tires are almost every driver, they are lying in the garage under the pretext "someday useful." It is time to apply them - let's do swans!
Before making a swan from tires, we find an old and unnecessary tire. It is best to take bald and without metallic Cord. Otherwise, the process can delay, processing will take longer.
We also need:
Coarse wire;
- screws;
- Paint.
Do not forget to prepare and the tools - a knife, jigsaw and drill.
1. To begin with, make a chalk our tire to know exactly where to cut. We divide the tire in half, one side is the beginning of the head, the second - tail.
2. Then draw along the line tire, separating the head, tail and wings. We start cut them. We use a knife, and in difficult places - jigsaw.
3. Now one of the most difficult moments cut on the tire part must be turned on the other side. It is best to do this with someone, it will be very hard.
4.
Frame swan ready. There are few steps left, one of them is to consolidate the neck. Drill make holes in the tire, and attach the wire.
5. Swan made! Kych him in red and white color.
These beautiful swans can be installed where your heart wishes.
It was one of the few winch design options. You can also make a swan, without turning the tire inside out, but then you have to cut the wings into 2 parts, as indicated in the photo.
Beautiful noble swans have long chosen not only lakes and ponds, but also country sites. On green lawns, elegant birds made from old auto strokes settled near the artificial reservoirs and in the gardens. Consider in detail several technologies for creating swans from tires and give recommendations for placement self-made product In the back area.
Use old things to create new and original crafts Designers are called Trasch art. The idea of \u200b\u200bcreating beauty from old trap willingly embody creative daches and gardeners. To implement their plans owners country areas Often use old car tires.
Swan is the most popular product of homemade masters from spent tires. They are created different ways, deactivate in the most unusual colors and decorate everyone to your taste.
Swans - Universal Garden Decoration and outdoor territory. They appropriately look near the artificial reservoir, the well, on the playground, at the entrance to the house or gazebo. In addition, some models have both practical purpose - for example, used for growing colors. Unusual flowerbed can play a leading role in a flower garden ensemble.
Despite the fact that the creation of tire swans has become unusually popular among dachans, products do not have repetitions. Each gardener tries to add to his masterpiece "highlight" and decorate its plot with original, exclusive exhibit.
The quality of the finished product and the simplicity of performance depends largely on the tire applied. Choosing the material, preference is worth paying the old tire with such characteristics:
Tip! In the marking of the tires should not be the inscription "STEEL", which indicates the presence of metal amplifiers in the tire
For work it is necessary to prepare the following materials and tools:
Before starting work, the tire must be cleaned, rinse and dry. To implement your idea, it is better to choose a cloudless day, so that the tire cutting and the swan assembly can be performed on the street.
Markup scheme determines appearance finished product. We give an example of the development of a homemade swan drawing for tires with the following characteristics:
Tire Swan: Scheme
Tire marking sequence:
Cutting tires is the most time-consuming process in the manufacture of a swan, requiring certain skills to work with tools, patience and high care.
Important! Hand brushes must definite - wear strong working mittens. Not excessive use and special glasses
Consider how to cut the swan from the tire on the applied markup. When working, follow the following rules:
After the end of the cut, the edges of the product must be processed. If the swan is made of a tire with a metal cord, then the grinding will need a Bulgarian. Capron threads can be cut off with a sharp knife.
All work on the assembly of the swan can be divided into the following steps:
The homemade exhibit is almost ready, it remains to give it an aesthetic appearance and install on the site.
Before painting, you need to check again, so that the figure did not have sharp edges and protruding wires. Especially if the swan is a decoration for the playground.
For painting, pick up paintwork, resistant to atmospheric influences. Color - at the request of the manufacturer. You can choose classic tones - black / white or create original installation, painting swan in a bright color.
The beak of the swan is better to paint red paint, and the eyes to build from wide bolt hats or pieces of rubber tire. On the bird you can create a imitation imitation and make small cuts on the wings. The royal and noble type of swan will give a crown from a plastic bottle.
Making a swan from a tire: video
We give a simpler example how to make a swan from the tire. Before working, the tire must be prepared: wash and dry.
The algorithm for creating a swan without tire turning:
You can make a beautiful flower bed from the tire, giving it the shape of a swan. Works are performed in the following sequence:
After drying the product, the flowerbed can be transferred to a permanent place, pour the earth and plant flowers.
Important! In the flower beds from the auto strokes, fruit and vegetable crops can not be grown, as the rubber is toxic and distinguishes harmful substances.
Make the original swan can be made of auto strokes, plastic bottles and corrugated hose. To implement the idea, you must prepare:
Manufacturing instructions:
Very organically swans look near its natural habitat - reservoirs. Swan can be installed near artificial pond or fountain.
An interesting option is the placement of the swan on the stand in the reservoir. The illusion is created that the birds have just flew to the pond in search of food.
If there is no reservoir on the plot, you can create a pond imitation and "settle" there a pair of swans.
Decoration of flower beds and lawn. For the stability of the composition, you can use an additional tire.
Against the background of the white swan-flower beds, bright red flowers will look.
White swan made of tires can be used for the decoration of the playground and garden.
From homemade swans, an interesting fence is obtained for the plot. Rubber birds are installed each other, creating the visibility of the partition.
After reviewing the presented ways to create products from auto strokes, you can choose for yourself the best option, how to make a swan from tires with your own hands.
Swans from tire: photo
