House, design, repair, decor. Yard and garden. Do it yourself

Today, many furniture and doors are made not from the wood massif, because the material is quite expensive and is not always functional for the manufacture of such structures. The tree is replaced by DVP and chipboard. These materials are based on wood fibers and chips. Through the use of such materials, the product is obtained light and hollow, so often careless motion can be hurting the canvas and make a dent or hole in it. Even with the worst handling of such a structure, scratches and chips are still inevitable. But this problem is corrected. IN this material We will tell you how quickly and just close the hole in the door of the Fiberboard.

Before close the hole in the wooden door or design of the Fiberboard, you must get a certain tools and materials.

The following materials will be required:

• mounting foam;
• putty;
• primer;
• sandpaper;
• polyester or epoxy resin;
• paints and varnishes.

In addition to the materials named above, in order to repair the doors from the fiberboard with their own hands, stocking tools:

• construction knife;
• brush for varnish / paint;
• spatula, suitable in width.

Repair sequence

When available required tools Both materials can be started. Next, consider how to fix the canvas if they struck the hole in the door from the fiberboard.

We offer you a consistent algorithm of action:

1. Before closeing the hole in the door of the DVP, remove it from the loops and put on a horizontal, smooth and stable surface.
2. Armed with a building knife, make a hole. To do this, from the edge you need to retreat some distance and confident and strong movement to produce a cut.
3. Now inside the door cannon need to be placed paper, newspapers, DVP cuts, chipboard, wood, chips. This manipulation will allow the design to purchase strength. In addition, the filling of space is able to reduce the consumption of mounting foam.
4. On top of the filling materials you need to post the construction foam.
5. When the mounting composition is completely dry and freezes, its excess should be removed, cutting off with a knife. If there are many traces of foam on the surface of the door, which is impossible or inappropriate to remove the sharp object, use the solvent.
6. The next stage of repair of the hole in the door of the DVP is a coating of a place where there was a hole, epoxy resin. Making this manipulation, be sure to wear gloves. This substance covers the foam, forming a dense protective crust on its surface. If the resin falls on the skin, you need to remove it as quickly as possible by the solvent.
7. After the frozen, the door surface is covered with putty. The required amount of material is recruited on the tool, after which it is evenly distributed in the slot.
8. When the putty dry, on the processed area you need to walk in shallow emery paper to clean and level the surface.
9. Door repair doors Complete the three layers of primer on the plane. When it dries, you can finally cover the door to varnish or paint.

Features of damage repair without explicit gaps

It happens that there is no obvious hole, but there is a dent. In this case, the question also requires an immediate solution and is no difficulty.

Powered in several stages:

1. Before closeing dent into the door of the Fiberboard, armed with a drill, start doing holes around the damaged area.
2. We take the drill of this diameter so that it was a little more packaging tube with foam. Than more holes You will do, the better the problem will be corrected.
3. Next, in each hole we put a little mounting foam. It should not get out of the holes. We act very carefully, because if there is too much foam, then she can inflate the door. Do not allow such a phenomenon, otherwise you will have to remove all the upper coating, and the foam under it.
4. If flaws and cracks passed along the perimeter of the canvas or through the entire area across, it should be very gently filling the space of foam. In addition, it needs to be blown not only under the crack itself, but further from its ends by 10 cm.
5. When the mixture is freezing, again with a building knife, we remove everything too much and grind the sandpaper.
6. The next step is to apply putty. When it dries, the surface is covered with primer. We apply 3-4 layers of this substance, each ball dries about half an hour.
7. After that, you can proceed to the final finish of the door.
8. Paint on the canvas is advisable to apply with a painting small bruster.

How else can you disguise the hole in the door?

It happens that there is no skills in repairing a person, and the opportunity to buy a new design or call the masters is also not.

Then he should listen to the following advice:

1. Mastering the hole in the door, provided that it is not too deep, it is possible by sticking the decorative film. Now there is a lot of colors for products: both under the wood, and imitation of other materials, and pictures, and abstraction and many other things. But before reagreeing the hole in the door from the fiberboard, decide on the design of the material.
2. As an option - close the hole with a mirror. You can choose a large model of the mirror, and you can be brought a small, calculated only on the face.
3. The mirror can be replaced by the picture, calendar, cute bass. They will close the hole, and attention will be distracted, and the interior will decorate.
4. An interesting option is borders around the perimeter and in the center of the door. You can also add elements from color or monochrome glass.
5. Another option to make a hole in a wooden door - hang photos in a frame or collage. You can also glue decorative sticker or applique.

We offered you a few options how to repair interroom door from fiberboard. Contact your imagination and come up with something original and beautiful, which will certainly fit into the interior design and will answer it to the destination. The big plus doors from the fiberboard lies in the simplicity of working with it, as well as in the set of options for fixing and finishing. We hope that our tips, how to fix the hole in the door from the fiberboard, will help you close the hole, remove the crack in the door canvase.

Repair doors from MDF - a very interesting occupation. It consists of a frame on which MDF sheets are pasted. Frame is usually manufactured from wooden bar. The door is inside the hollow, so light and not particularly durable.

Repair the door from the MDF is not more difficult than to close the "beetle" on the body of a beloved car. Although the easiest thing is, of course, buy a new one. But when finances sing romances and simply lacks funds to the rescue, folk savings comes to the rescue.

The described repair methods, undoubtedly, will help you to save a significant amount of money, which would have to lay out for a new one.

When choosing the materials you will use, it is necessary to take into account that you need to use those that are designed to work with wood, and not metal products.

Repair the door from the MDF is completely easy. Before you begin, it is necessary to determine what damage it is applied. Depending on it, two types of repair can be distinguished:

1. Repair scratches.
2. Repair of a hole.

How to remove scratches

When repairing scratches on the door, the following tools and materials will be needed:

1. Sandpaper (with marking from 150-200).
2. Wood putty.
3. Spatula for putty.
4. Soil for wood.
5. Enamel on a tree (for MDF, a special two-component paint is used).
6. Paint brush.

Remove scratches from the surface of the MDF door can be removed using a low-fat colored wax chalk for retouching small scratches, cracks and small holes.

First, you need to clean the scratch and the area around it around one centimeter. Then you need to clean the cleaned area of \u200b\u200bthe door from dust and small wooden particles.

The next action you need to put the wood putty on the purified area, and then the spatula must remove its residues and at the same time try to make the surface perfectly smooth. After drying the putty, it must be re-cleaned, in order to align the remaining irregularities. Clean the shallow emery paper.

It should be noted that putting the putty on the MDF surface should be very careful, trying not to make new scratches. To avoid this, you need to use rubber spatulas.

Then, on the processed area, we apply a smooth layer of wood soil and wait for it to dry. After the soil is dry, all the door is a smooth layer cover enamel (paint) on wood.

How to remove the hole

When repairing a hole, you must have the following materials and tools:

For repair, the door will need the following tools: hammer, saw, plans, chisels, screwdrivers, pliers.

1. Construction knife.
2. Newspapers or something similar.
3. Mounting foam.
4. Polyester or epoxy resin (and that and other may be purchased on any car market).
5. Emery paper (with marking from 150-200).
6. Putty on wood.
7. Putty knife.
8. Soil for wood.
9. Paint, which was indicated for the first case.
10. Paint brush.

When repairing the hole first, it is necessary to cut a hole that will be slightly more of it. Perform such work is easiest with the help of a building knife. In this case, if possible, it is necessary to try to make a chamfer to a depth of about 0.5 cm.

Then from the inside around the edges of the hole you need to fill with newspapers or just paper. If this is not done, then when the door is filling, a very large number of mounting foam may be needed. After that, the hole must be filled with mounting foam. As soon as the mounting foam dries, the protruding part is required to cut to turn out to be a smooth surface.

The resulting surface requires a polyester or epoxy resin to form a solid surface. This operation is preferable to do the whole, putting rubber gloves on the hands, because when a resin hit, it easily sticks easily, and it is possible to remove it only with solvent. And the solvent, in turn, like a resin on the skin of the hands, may cause irritation.

As soon as the resin hardens, it is necessary to put a putty on the wood. The dried putty must be cleaned with sandpaper, so that it turned out a smooth and smooth surface. You should use paper with the specified slightly above marking.

After stripping on the putty, it is necessary to apply the wood soil. It is best to do this several times with a time interval at least 20 minutes. After drying the soil on the surface of the entire door of the MDF, you must apply the selected paint.

It should be noted that the primer is best to apply small painting brush: This will help avoid divorces.

As can be seen from the foregoing, to repair the door from MDF is not so difficult. And the time spent during repair with your own hands compensates for a significant amount of money.

Repair of interroom doors can be done to everyone. To do this, you only need to arm a tool and knowledge. You can repair any doors from MDF, DVP and chipboard (veneered and laminated), natural tree. It is possible to carry out a lot of manipulations with them: to close the smelting, put a patch, repent, move and tinker.

Causes of problems

Mechanical damage occurs due to non-accurate operation or installation:

• scratches and dents - a familiar phenomenon in families with young children;
• moving or dropping objects sometimes leads to slobs in the doors from the fiberboard.

As a result, incorrect installation collide with such difficulties:

• skew;
• poor adjoining;
• friction.

The tree is hygroscopic - easily absorbs moisture and gives it. In this regard, the violation of production technology and operating conditions leads to the following unpleasant consequences:

Correction of mechanical damage

To repair small damage to the interior door with their own hands, we need:

• magaza or wax pencil;
• a piece of felt.

Small scratches and dents almost always occur after a brief exploitation. Mind them with the help of a special wax pencil, which can be easily in the market building materials. The color of the pencil must match the shade of the doors. The place of the seal is triturated by a piece of felt.

How to repair dents and chips on wooden interroom doors

For sealing dents on wooden products, We suggest the following: the chisel hollow out a piece of wood exactly corresponding to the size of dents and, labeling with glue, apply to the excavation. The location of the compound is pressed by clamp, if damage to the edge. If the latch is in the midst door canvas - It must be put on smooth surface, cover the board suitable size and press a heavy item. The protruding sections of the patchwork believes the chisel and grind large, and then small emery paper. Painted suitable paint, open with varnish.

Repair of interroom chipboard doors do it yourself

To close the surface damage from a veneered chipboard, use veneer chosen in color and texture. You need to remove a damaged piece with a chisel and glue a new one. It is easier to close the defect if the veneer of the tangential cut (wavy, twisted structure), then the repair is not very noticeable. With a radial incision (straight, parallel lines), it is harder to correct, as it is difficult to choose a drawing. Press the bonding place is similar to example above.

Restoration Splocks on the doors from the fiberboard

Pierced DVP doors can be repaired with your own hands, inserting the bottom of the product ventilation lattice. If the hole was formed from above, then make a tab of similar material, glass, etc. Cut the symmetric hole, whose ends wooden barsTo close the emptiness. Insert the pre-prepared sealer wooden or from the MDF (there is on sale), lay insert and fix another panel with back side, scoring with stiletts.

Correct the disadvantages allowed by incorrect installation

1. If the door opens poorly or friction occurs, it is removed from the edge with an excess plan, grind, paint and lacquer. The gap between the box and the doors should be no more than 1.5 - 2 mm.
2. If the door spawns when closed, the reason may be that it rests on a quarter of the box. In this case, stick the door leaf or box. Also, the problem can be in the montage of the loops on the door.
3. The door sedimentation can be repaired, putting the washer on the rods of the upper and lower door loop.

Eliminate production marriage with your own hands

1. Opened doors - it is basically the result of unfair manufacturing and to resolve the situation to refer to the manufacturer. But, if he was not decent, to repair will have to do with his own hands. In this case, it is necessary to disassemble the product to the details, pollute all the coating to the bare tree, clean the remnants of the glue on the joints. Promoting joints with glue, alternately connect the details, clamping the clamps. Then the doors are re-stained and lacked.
2. If the doors are made of wet material, subsequently in a dry room, they dry and the gaps are formed, the door is loosely adjacent to the box or does not close. In this case, the edge is performed by the bar of the desired value, then align in size with the door web, polished and covered with the necessary paints.

Hollow interior doors require a careful relationship. Lightweight design is easy to damage. Squares, cracks and dents are formed with improper operation and mechanical damage. However, minor defects can be corrected independently. How to close a hole in - in this publication.

Possible causes of damage

Intercomed door blocksFor the manufacture of which the fiberboard, chipboard, MDF and other lightweight wood materials, weakly resistant to various damage. Increased humidity Air and bad antiseptic processing lead to rotting material. Drying loops and displacement of the box can become reasons for rubbing, loosening and forming chipping on the design. The detachment of the upper layer of the canvas is possible with incorrect cladding.

But the most common damages are cracked, dents and holes. Most often, such defects occur with a strong mechanical or shock load. For example, when moving furniture or household appliances Perhaps damage door construction. What to do in a similar situation, and how to fix the hole in the door on your own?

What to close a hole in the interroom door

Any repair work In the house or apartment begins with the definition of the complexity of the problem. Minor damage does not require the intervention of specialists, can cope with such repairs can independently.

Preparation of instruments and materials

First you need to figure out how to close the hole in the door, if it is interroom. So, the following materials and tools will be needed in the process:

• construction knife;
• medium width;
• brush for applying a varnish;
• emery paper of different grain (or grinding);
• construction Scotch;
• foam assembly;
• solvent;
• putty;
• polyester or epoxy resin;
• paintwork for working with wood;
• true for wood.

If you need to close the hole under the door or repair the box, you will use building level, Pencil, roulette and lubrication for loops.

How to fix the hole in the interior door: step by step instructions

Repair work is produced in a horizontal position. The door design must be removed from the loops and put on a smooth and clean surface.

Before close the hole in the interior door, align the edges of the hole with a construction knife and fill in inner space newspapers, paper or cardboard. Such measures allow us to slightly lose design, give it strength and reduce the consumption of mounting foam. Then proceed to filling the hole by mounting foam.

After complete drying, we begin to clean the canvas. The protruding the remains of the construction foam remove the knife. Please note that only large pieces of foam can be removed with a knife. Small residues are cleaned with solvent. Otherwise, new scratches and cracks may appear on the door surface.

To increase the strength of the structure, we apply a layer of epoxy resin. Apply a putty on top. Each subsequent layer is applied only after complete drying of the previous one. Dry putty process with grinding or sandpaper shallow grain. Cover primer I. paint and varnish materials. Now you know how to close the hole in the door of the Fiberboard, chipboard or other wood material.

How to close a hole in the door of MDF without an open slit

The wooden door does not always have open damage, however, the presence of dents and other defects also require repair.

To uniform filling in the inner space and warning of the bend, the designs will be needed and drill. Wooden canvas drill in several places. In the resulting holes insert a balloon tube with mounting foam. Fill in the inner space of foam. We work carefully to prevent the deformation of the design.

The next stage is the alignment of the door canvase. You can use construction foam. This work plan requires certain skills, since the application must be uniform. Further algorithm of action is no different from the previous version.

Diatic decoration

In complete, we will deal with the question of how to reorganize damage. How to repair the door from MDF with a hole - figured out. Decoration does not require special skills and skills. The simplest options:

• close the processed place with a mirror with a mirror or any other scenery;
• stick a self-adhesive decorative film;
• hang a poster or collage with favorite photographs.

Tips and recommendations considered in this publication will help eliminate damage to the interroom door design with their own hands. Now you know how to close and how to reorganize a hole in the door.

The hole in the door can be formed as a result of a variety of reasons: random strikes, mechanical impact or just time. However, this little misunderstanding does not mean that it will be urgently. The hole can be masked or close.

Masking methods

Masking a hole is an easier and cheap way to cope with this trouble. Depending on the style of the interior of your home, your personal preferences and fantasies. Possible options:

1. Hang a poster / sign. This option is suitable for a children's or room weathered in a non-storm style. Today you can find many funny posters and tablets that disguise the hole and at the same time will raise you every day.
2. Stick the mirror. Self-adhesive mirrors - a great and practical option to get rid of the hole. They have a little weight that will withstand the door of any type, various sizes and shapes.
3. Pack the self-adhesive film. IN special stores You can find a huge variety of colors and textures of such a film. It is possible to glue it only on one or both sides of the door.
4. Drive the door canvas. To do this, you can use various drawings, photos, pieces of fabric, etc. You can apply any option that your fantasy will give and allow the interior.

If the door design and your budget allow such an option, you can order stained glass windows for a part of the door with a hole. Such glass can be made to order and contact the wizard for high-quality installation.

Door repair

If you do not want to change the initial appearance Doors, you can repair it. Moreover, it is possible to close the hole independently with the help of a low expansion foam.

• Cut the uneven edges of the hole.
• Lay in the inner space by any grain material (for example, packaging paper).
• Fill mounting foam. After her froze, cut down the pieces of slices.
• Lach the surface with mastic.
• Sharpen (you can use the putty usual / on wood).
• After grazeing the putty (at least 12 hours), walk through the surface with zero eye.
• Slide the plot of suitable paint. You can also create a unique pattern on this place.

If the hole appears in the door, do not be discouraged. You can cope with it using conventional tools and / or fantasy.