Usage roll materials for surface cladding is a popular and demanded solution that allows you to achieve a high-quality result in a short time. But the finishing technology has some nuances. It is especially difficult to glue wallpaper in the corners: the resulting coating should be free from distortions and defects. The most suitable method is selected depending on the situation.
The existing varieties have a certain order of wall cladding, which allows you to achieve the best result.
The technology for working with this option is not very complicated if all the processes are performed correctly.
Step-by-step instruction:
The vinyl layer on the canvas is strong enough, so the wallpaper can be safely smoothed with a wallpaper spatula, without fear of damaging the integrity On a note! In the absence of experience and the need to fit a complex pattern, it is better to prepare: for this, the strips are placed on a horizontal surface, aligned with each other, and the size of the necessary fit is noted.
The gluing of this variety is rarely difficult. For the process, you can use any glue, including one prepared by yourself.
Algorithm of actions:
It is impossible to pull the web at the joint by force, the connection is leveled exclusively with a rubber roller All processes, especially smoothing, are carried out with care, because even multi-layer products are very easily damaged.
To glue this variety, a special version of the glue is used, since the material is quite heavy. The preparation of the binder is carried out strictly according to the instructions and is applied only to the wall.
Process diagram:
It is important to properly saturate the base: do not leave dry areas. Places beyond the width of the canvas are necessarily affected.
Advice! To speed up the process, the composition is best applied with a roller.
Additionally, we suggest watching a video, where the process of gluing non-woven wallpaper is considered.
The technology of laying canvases on external and internal corners has differences.
These areas are the most visible, so they must be glued with great care. It is easiest if the angle is perfectly even, but this is quite rare.
In the presence of defects, the process is complicated. If the corner is filled up, then you will need to trim the canvas along the bend line in order to impose one section on the adjacent one. This method is not suitable for varieties with complex patterns.
There is another way:
Docking the outer corner with a trim on one of the adjacent planes is considered the most effective way arrangement This method does not completely correct the skew, but makes it easier to further adhere and fit.
The technology for working with such a site is almost identical to the previous process, but has some nuances:
Technically, joining an inner corner is not much different from similar works on external structures, but this process is considered easier, since the internal corners are visually less noticeable This technology allows you to glue different types products, but if the corner does not involve trimming, stacking is carried out in a standard way. To do this, the joint of both sides is made with a margin in order to level the unevenness by fitting and cutting at the place of combination. This will take longer, but will remove the overlap in the corner.
Video tutorial: how to glue wallpaper with trimming in the corners
Work technology:
If there are no problems, you can dock directly along the inner corner, but this will require a certain level of skill.
Wallpaper with a pattern is joined according to the same principles as without a pattern, but if you pre-stick a horizontal mark made of masking tape on adjacent canvases, then it will be easier to combine the ornament Perfectly even corners in rooms are rare, so to eliminate various problems, you can use the recommendation that many designers use - a combination. It is necessary to glue the transition from wall to wall with wallpaper with a pattern or with bright colors. Part of the pattern should go to the adjacent side, where it is trimmed at right angles and aligned with the plain material. The joining line will turn out to be smooth, and the existing shortcomings will not be conspicuous.
Renovating an apartment or house is a very complicated and time-consuming process. And if workers make it for you, it is also expensive, since the price for the services of the craftsmen is often the same as the cost of the material. Therefore, if you are at least some part renovation works do it yourself, you can save a lot. Many people successfully glue wallpaper on their own, and do not find anything difficult in this, except how to glue wallpaper in the corners.
Wallpaper gluing in corners is a responsible and important stage of work
Even in very good apartments there are bad angles. They are not good because they are not perfectly flat. What do the masters advise?
When pasting the outer corner, make sure that the strip fits snugly against the wall
Never glue an entire strip of wallpaper. If the corner is uneven, the strip will fold into folds and will not converge with the other strip. Leave a ledge around the corner by 1.5-2 cm, then the strip will lie against the wall. Be sure to use a plumb line when gluing thick wallpaper. Glue the piece with a slight gap to the adjacent wall so that it is as vertical as possible.
If there are switches or sockets close to the corner, you must first remove the covers, not forgetting to turn off the electricity in advance. Stick the canvas on sockets and switches, then make cuts on the wallpaper and cut the circle slightly smaller casing. Then put the covers back in place.
When pasting the wall near the door, it is better to approach the doors from both sides. The strip of wallpaper that grips the door must be cut vertically before the start of the frame. It is attached along the edge of the wall. The overhang should be cut and fitted over the door frame.
This step is performed long before the immediate pasting of the wallpaper at the stage of wall putty. The corners of the room should be equipped with special plastic corners. They are attached to the walls with putty, and must be fixed very securely. After that, you can proceed to the design of the corners of the room.
Do not glue all corners at once. Having chosen the corner from which you start, prepare a strip of wallpaper of the desired length. Cover the area with wallpaper glue along the width of the cut strip (plus 3-5 cm), do not forget to treat the plastic corner with glue. When the section of the wall and the corner are treated with glue, attach the wallpaper there. If you started gluing from left to right, you need to attach left side to the inside of the corner so that the strip is perfectly aligned along its entire length.
Level the wallpaper well in the corners to visually hide existing defects
The wallpaper is rolled out with a special roller or spatula. After that, the next section of the wall is covered with glue, and the wallpaper is glued to the next corner. How to glue the closing corner? A new strip must be associated with the last strip of wallpaper. Roll the glue towards the corner, and when the wallpaper is glued to the inside of the corner, cut off the excess section along the inner line of the corner with a clerical knife.
How to glue non-woven wallpaper in corners
Non-woven fabric is a special material that consists of cellulose and non-woven fibers. These are wallpapers that are intended for painting, since their outer layer is not resistant to mechanical damage. It is much easier to glue non-woven wallpaper in the corners than any other wallpaper, since the glue is applied only to the wall, and dry wallpaper is attached to it. Having previously decorated the corner of the room with a plastic corner, stick it in the same way as described above.
With a clear geometric pattern on the wallpaper, distortion must be minimized
If the pattern on the wallpaper has vertical lines, it is in the corners of the room that its distortion will be especially noticeable. And if the drawing is horizontal, it will be skewed in relation to the ceiling and baseboards. How can you avoid such troubles? It's simple. Firstly, do not forget to make a small overlap on the adjacent wall, and secondly, hide the existing joint at the top of the corner. Thirdly, try to stick wallpaper in the corners of the room so that an even edge lies exactly along the vertical line you drew (along a plumb line). In this case, the other edge is trimmed along the edge of the corner.
You can hardly avoid the pattern shifting altogether - a slight shift is likely to remain. But this is such a drawback that only you will know about. After all, in order to find it, you need to carefully study the corners of the room. If you follow all the rules, the wallpaper will lie vertically on an adjacent wall, which means that the distortion of the pattern will not be noticeable.
Wall decoration with wallpaper is the most popular option for decorating walls in rooms. Undoubtedly, pasting wallpaper on flat walls is quite elementary and requires only a little skill, but wallpapering the corners of a room with wallpaper is technically more difficult. Before you stick the wallpaper with your own hands, you need to properly prepare the walls.
First you need to clean up old wallpaper or paint, apply primer to the walls and level their surface. And only then begin to paste over the corners with wallpaper.
So, repair specialists distinguish the following stages of this process:
The adhesive should be applied to the wallpaper strip and the corner of the wall. Next, you need to attach the wallpaper to the corner of the wall as follows - if the pasting process starts from left to right, then the left side is applied to the inner side of the corner to evenly cover it.
At this stage, you need to clearly understand that you need to wallpaper the outer and inner corners in different ways.
Outside corners can be glued in two ways: firstly, if outside corner has a flat surface, you can not waste time leveling it and immediately apply wallpaper to the corner, then use the level and measure the edge of the strip so that the remaining stripes lie evenly; secondly, to glue the outer corners, first you need to lead the strip around the corner by 4-5 cm, and glue the next part of the wallpaper at the top. Using a utility knife and a ruler, cut these layers vertically.
Internal corners require more attention. Wallpaper must be glued so that they go on the adjacent surface by about 3 cm, but not more, otherwise they will wrinkle. The fold and turn of the wallpaper must be coated with glue. Next, you need to measure the width of the wallpaper located on the adjacent wall, mark the allowance of the glued side, which is glued at a distance of about 2 cm from the corner and a vertical line is drawn through it using a plumb line - this will mark the edge of the wallpaper to be pasted.
Alignment of wallpaper occurs by rolling, for this there are special rollers and spatulas.
All the stages of wallpapering in the corners presented above are sequential.
Plastic corners on wallpaper are a good finish for finishing corners - they have protective functions and give the corner a finished look.
Construction markets offer different decorative corners:
For arched outer corners, it is better to use corners with the following approximate dimensions: 5 × 17.7 × 17.10 × 20 and 15 × 25 mm. It is recommended to install plastic corners with silicone sealant, it is colorless and has good adhesion. The length of the corners ranges from 3 to 7 m, so it can be adjusted to individual dimensions.
Decorative plastic corners help to protect the wallpaper from mechanical damage at the corners of the wall, in addition, they are not expensive and easy to install.
Non-woven wallpaper is particularly durable, but it is quite difficult to work with them, especially on corner surfaces, because they are not elastic.
To paste over the corner of the wall with such wallpaper, when cutting off a part of the wallpaper, it is necessary to make an allowance of 1.5 cm, this allowance should overlap.
Need to know little secret- gluing non-woven wallpaper will be easier if you make equal cuts along its entire length along the edge.
In this case, the glue is applied only to the wall, and the wallpaper must remain dry. In the work on decorating the corner with such wallpaper, it is better to first use the corner, then unnecessary crooked places will not appear. If the choice is made in favor of wallpaper with a pattern, in this case it is necessary to carry out a high-quality adjustment of the pattern in the corners. In order to keep the drawing intact in the corners, you need to trim the next strip from the corner to the drawing of the already pasted over the wall.
Here are some tips:
Meter wallpaper is a wide non-woven fabric a little more than a meter. This type of wallpaper helps to paste over faster big apartment and the selection of the pattern becomes easier. In order to stick meter-long wallpaper in the corners, you need to overlap up to 3 cm on the next wall. The rest of the procedure will not differ from the standard pasting of corners, which is described above.
Then proceed according to the following plan:
So, knowing the technology of gluing wallpaper in the corners, you can perform quality repair do it yourself and also help your family in this difficult task.
Date: 05/13/2017
A lot of people who decided to make repairs in an apartment or house with my own hands, believe that high-quality wallpapering will not be difficult for them. Yes, to some extent, this finishing material is quite practical, but only on flat sections of the walls, which cannot be said about the corners. How to glue wallpaper in the corners? This is the question that people who start repairing without professional help face.
It is in the corners that gluing is a laborious process, which makes it difficult and calls into question the quick completion of the repair. So you should approach this issue with all seriousness and study with scrupulousness all the nuances of such an operation, because bad wallpapering in the corners can generally ruin the whole look.
How to glue wallpaper in corners
Wallpaper is and remains the most popular finishing material for any kind of premises, whether it be a room in an apartment, an office, or a beauty salon. The quality of wallpaper varies, and you can find absolutely for every taste, color range and cost.
Sometimes cheap nondescript wallpapers transform a room so much that they seem to be no worse than expensive ones, that is, now the range of wallpapers on the construction market is different, and there is a high-quality and at the same time cheap stuff- two in one.
Today, in order to glue wallpaper, you do not need to have professional skills, but you need to know the gluing system. The walls first need to be aligned around the perimeter, in the corners, and from here the problems begin for non-professionals.
Wallpapering in the corner
It is not recommended to glue a whole strip of material. In the presence of uneven corners the strip lies in folds and does not converge with the other. We recommend leaving the ledge behind the corner by 1.5 or 2 centimeters and then the strip will lie flat. Choosing a high-density wallpaper, use a plumb line. Glue a piece of trimmed wallpaper with a small overlap on the adjacent wall so that it is as vertical as possible.
If there are switches, sockets in the corners or in the vicinity of them, it should be before gluing and any construction works turn off the power supply and remove the covers. Glue the material completely onto the raised parts, and only then carefully cut, making small cuts.
When starting pasting the wall near the door, it is important to know that the strip of wallpaper must be cut vertically before the frame starts. Then it is attached along the edge of the wall. Cut off wallpaper overhangs.
Non-woven wallpaper - how to glue wallpaper in the corner
Wallpapering should be done according to the existing technology, observing the sequence of processes, as regards not only the corners, but in general the entire procedure for pasting walls with flakes.
It is better to prime the surface with professional products that are sold in containers of various prices, but can also be primed with diluted glue, but is not particularly welcome. A special roller or a wide brush will help you prime the surface. Due to the fact that the pasting in the corners is especially difficult, there is such a nuisance as the displacement of the picture. On the walls, the geometry of the drawing has been preserved, but in the corners everything has gone and now spoils the general background. Therefore, the most responsible approach is to inspect the corners, if there are irregularities, eliminate them if any.
Preparing walls for wallpapering
After you have pasted over everything flat surfaces walls, you have to go to the corners. Now inspect, and noticing irregularities, proceed to sanding - having carefully putty. After the putty has completely dried, it is necessary to sand the entire surface with sandpaper to achieve an ideal smooth surface so that the wallpaper does not come off in the future.
Now the corners also need to be primed. If you do not have the skill of filling, then there is a way out, just buy the same type of wallpaper, or with a simple pattern that does not require further docking (paper). So part of the question of how to glue wallpaper in the corners can be considered disclosed.
After leveling the surfaces in the corners, we proceed to applying glue, it must be distributed with all care along the height of the walls, and in the corners most conscientiously, because in these places the wallpaper most often peels off. Using a roller, distribute the glue along the entire length and with a brush in hard-to-reach places.
Applying glue to wallpaper and walls
Finally we got to the important part of the corner gluing issue. The pros of this case recommend sticking a piece of canvas in the corners, even if the whole piece is perfectly straight. This can be explained by the fact that there is a high probability of distortions in the corners, and the subsequent sheet does not fit at all, and after drying, folds can be found. Professionals of room decoration advise to cut wallpaper canvases so that the side goes 50 mm to the next wall. Below is a drawing of wallpapering in the outer and inner corners.
Did you know: a nuisance for beginners in this business is the curvature of the gluing areas. Such a defect in the surface of the eyes cannot always be detected, therefore a list of tools will come to the rescue: a plumb line and the same building level. They measure the corners before gluing the wallpaper.
If there is quite a serious "blockage", then it is better to come to a method of "cutting" in these places. This method is used for dense wallpaper - vinyl.
According to this method, the material is passed 50 mm onto the adjacent wall around the corner, and the next sheet is glued with an overlap.
The next step: in the middle of the corner, a vertical cut through two layers of wallpaper is made with a special construction knife under a level or ruler in the direction from top to bottom.
The scheme of gluing wallpaper in the corners
Throughout the entire process, the iron ruler must fit snugly against the corner and be pressed tightly so that there is not the slightest movement. Otherwise, a shift along the cut canvas is ensured. Craftsmen recommend using a long metal ruler, building level, which has more weight and has a wonderful abs that interferes with movement.
In order to avoid the appearance of folds in the inner corners, these canvases should be divided into two parts before gluing the wallpaper. The first step is to glue the material to the corner of the room, then you need to accurately measure the distance from the last glued piece of wallpaper to the corner bend, and add 10-12 mm to the resulting figure. Next, one prepared part is glued to the wall with a cut edge at an adjacent corner. Adjust the edges as usual, whether it's top or bottom.
Now, using a brush or rag, press the wallpaper into inner corner rooms. If irregularities arise, such as warping of the material, then take a special knife and make cuts, while pressing the wallpaper into the wall. Then glue the next part with an overlap on the glued material, pushing it tightly against the wall with a brush. Finally, cut off the remnants at the bend with the same knife.
Tip: If your angular inner and middle parts have small bulges, and the bottom is filled up slightly inward, it is better to press the cut edges with an overlap. When pasting a room with dense (vinyl) wallpaper the best way- this is the use of glue with a transparent base at the joints, this glue is suitable for dense materials.
Gluing the outer corners of the room requires calculating the length of the wallpaper in advance, and so that the canvas is not enough, but he could bend around the convex part of the wall from 21 to 25 mm. When glueing dense quality wallpaper, know that by making light cuts, for a smooth styling of the strip.
How to glue wallpaper in the corners correctly
So, on dense wallpaper using an iron ruler and scissors, cut off excess strips of material, leaving a minimum of an edge, the visibility of which will not be visible under the next canvas. On top of everything, the next strip is glued with an overlap of 5-6 mm. If you have chosen a smooth wallpaper, then immediately iron it with a roller, and with a convex pattern, voluminous ones can be passed very slightly with a rag.
The vertical pattern of the wallpaper makes it difficult to stick in the corners, because distortions are especially noticeable in these places. A pattern with a horizontal position is no exception, for example, after gluing it can be completely skewed. To avoid such incidents, it is necessary to make a small overlap on the neighboring wall and hide the joint at the top of the corner.
Tip: the difficulty of pasting corners with wallpaper is to follow the rule - the edge lay flat along the plumb line, and the other should be cut along the edge of the corner.
A non-professional will not be able to glue the wallpaper and at the same time without the pattern shifts without experience. The main thing is to make it less noticeable using the instructions provided above.
Repairing an apartment, house or office takes a lot of time and effort, as well as money if you decide to seek help from hired workers. But thanks to the instructions given to you above and following them exactly, you will be able to proceed with self-finishing by taking the time and attention to study the wallpapering in the corners. Pay attention to the presence of defects, whether your walls are even, and draw preparatory work to eliminate irregularities. In addition, batteries and pipes often pass in corners, interfering with the gluing process, making repairs a hassle.
If you approach this task responsibly, taking into account all the recommendations and rules, then you will expect quite a wonderful result, no worse than if the gluing was carried out by a professional team of craftsmen. By completing the finishing work with your own hands, you will significantly save money. Good luck and a good completion of your home renovation!
Modern wallpaper does not dare to call the language a cheap finishing material - vinyl, non-woven, vinyl on a non-woven basis, textured and paintable ... You will admire the result of pasting the walls for the next 5-10 years. Most often, problems arise with how to glue wallpaper in the corners. Let's figure it out together.
Paper wallpapers are the timeless classic of renovation. Their enduring popularity is due to two factors - low cost and wide assortment. However, it should be understood that paper rolls, no matter how beautifully decorated they are, remain a very short-lived material, and it makes no sense to glue them in the hope of a long service life.
Within a year or two, they will lose their former attractiveness, and if there are small children or animals in the house, this process can accelerate significantly. However, this minus can be used for the benefit in cases when you need to make an easy redecorating v rented apartment, or whenever you like to experiment with the interior.
Vinyl wallpaper on paper backing- a more durable finish option. Front side, on which the bulk of all operational loads fall, in this case is performed by a layer of polyvinyl chloride. And he has a lot of positive qualities:
Paper-backed vinyl wallpaper lasts an order of magnitude longer. Among the disadvantages, one should remember about the airtightness of vinyl, however, if you wish, you can find more modern types of finishes on the market that are devoid of this problem. Glue paper-backed vinyl rolls in the same way as ordinary ones paper wallpaper, therefore, for most, it will not be difficult to glue the canvases without special preparation.
Just keep in mind that the vinyl layer significantly increases the weight of the canvases, therefore, the usual wallpaper glue it will not work here, you need glue for heavy wallpaper.
The fact is that the glue is applied only to the wall. There is no need to apply it to canvases and wait for them to absorb it and swell... For the joints to be perfect, very careful marking is required. Non-woven wallpaper is another variety finishing material, made only of non-woven fabric. Wallpaper can have a textured pattern, but, as a rule, these are smooth canvases with interesting patterns. They are glued in the same way as the previous version.
Traditionally, the most difficult places in the gluing process are the corners. In most cases, they are far from ideal, therefore, if you start gluing joint to joint from the corner of the canvas, you can get a significant vertical skew. Many people mistakenly believe that distortions can be avoided if windows or doors are taken as a starting point for pasting walls, they say, they are probably perpendicular to the floor.
However, this is not always the case - you can check window and door frames for errors using the most ordinary plumb line. It is possible that you will be surprised how you got along with such a curvature before. The tradition of gluing from the window was carried out, first of all, due to the need to glue paper wallpaper with an overlap. If you glue them clockwise from the window, then the joints will not be so noticeable. However, in the case of vinyl or non-woven wallpaper, this is not necessary at all.
Ideally, if at least one corner is even, you can start from there. But it is best to do a thorough marking around the perimeter of the walls, focusing on the plumb line. In this case, you will see the general picture in advance, and the curvature of the corners will not be so noticeable against the background of perfectly vertical canvases. If you make the markup and glue the wallpaper on a non-woven base, then it makes absolutely no difference where you start from - from the window or from the middle of the wall.
The first rule of perfect gluing in corners is not to glue the whole canvas into the corner. In most cases, this is fraught with inconsistency with the next web and the formation of folds. If you have chosen an expensive type of finish, for example, silk-screen vinyl wallpaper with a complex pattern, then it is best to pre-align the corners with plaster or putty, depending on what kind of unevenness is in question.
If the deviations are not so noticeable, then you can hide small irregularities with the help of an overlap. To begin with, on one of the walls, which rests against the corner, we glue the canvas so that it goes on the adjacent plane by a maximum of 4 cm.Please note that the corner should be very carefully glue with glue so that the canvas has maximum adhesion to the surface. Using a spatula or the blunt side of a knife, carefully push the sheet in the corner - proceed carefully so as not to tear the sheet. Then use a rubber roller or sponge to remove any air bubbles.
The next crucial step is gluing the canvas to the adjacent wall. First, take the measurements again - it is necessary to ensure that the edge of the new canvas closest to the corner overlaps the already glued one by 2-3 cm, while the edge farthest from the corner goes right next to the new one.
Then, using a plumb line, we define a vertical line that runs at the overlap from top to bottom. Carefully mark it with a pencil and use a ruler and a sharp knife to cut through two layers of wallpaper at the same time. The surplus of the upper canvas will fall off by itself, but remove the remnants of the lower canvas by slightly bending the upper layer. Re-coat the folded edge with glue and press firmly against the wall. If you did everything correctly, the result will please you.
With the help of an overlap, the problem of pasting the outer corners is also solved. Only the process looks a little different. The first sheet is glued in such a way that one edge is wrapped around the corner by a few centimeters. During the alignment process, it is likely that several cuts will have to be made to avoid wrinkling. Press down the material well with a sponge or spatula and allow the glue to harden slightly. Then cut the strip bent around the corner so that only a thin edge remains, no more than 1 cm.
Before you start gluing the second sheet, take measurements with a plumb line to determine the edge farthest from the corner. Focusing on it, we glue the second canvas in such a way that an overlap of no more than 5 mm is obtained in the edge closest to the corner. Thus, you will get an inconspicuous joint of the canvases.
