House, design, repair, decor. Yard and garden. Do it yourself

Interesting homemade For giving waiting for you in this article. You will learn how to make a lawn mower from the old washing machine, make a sink, country souls, dryer from priest materials.

Useful homemade for summer cottages - washing with their own hands

Not everyone has a financial opportunity to buy car "Karcher". If you can not buy it, why not invent? Homemade washing will allow you to do without water supply, reduce water consumption and wash the car thoroughly, fence, garden track or other items.

That's what you need for such a homemade for giving:

• plastic canister with a capacity of 5-20 l;
• set of hose connector;
• nipple automobile;
• cut of the hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• pistol for watering.

Take a set of hoses, which include 2 connector, 3/4 threaded fitting, 1/2 transitional coupling.

This is the principle of operation of such a homemade for the cottage: you can connect a gun with a hose, attach this device to the bottom of the canister. Nipple will be built into her neck.

Fill the container with water, but not to the top. Then tighten the lid and pumped into the air. The pressure will be created here, and water will run well when you will press the pistol trigger. That's how to assemble such a mini sink.

Carefully knife tip Cut the hole in the lid. It should be slightly smaller than the diameter of the legs of the nipple. Also ride the circle of the desired diameter at the bottom of the sidewall canister.

Insert nipple into the cover.

Now, helping yourself with a wire, put the coupling to the hole intended for it. Apply the silicone sealant to fix the seat of the coupling with Cannis.

It is necessary to spin the lid and carry out the rest of the work only after the complete soot of the sealant. Then you connect one end of the hose to the water pistol, and the second to the canister.

Pour into the water capacity, but not to the wind, so that the air pumping place remains. But do not pump a lot so that the canister is not deformed and did not burst under pressure. See how the fitting should be twisted and connectors are installed.

If everything is done correctly, then when you press the water pistol, water will beat a good jet. The pressure you can adjust, tiping the pistol tip.

In the country, you can hardly do without a soul. Try to make it unusual, and tropical, then you can enjoy even more water treatments.

How to make a tropical shower of girlfriend for giving?

If you just recently purchased the site and you still do not have a wave room, then you can take a shower right on the street, having sorrified a small area near the fence of the curtain. To make such a tropical shower, you will need very few components, it is:

• bracket;
• wire;
• flexible hose;
• metal beer bank;
• hose adapter;
• awl;
• nails.

Send a metal bracket on a wooden fence so that the device succeeds in the desired height. Screw to the tip of the adapter hose, lock it on the slots of the beer bank. The location of the connection can be treated with sealant. With a selection, make a set of small punctures in the bank.

Tie the top of the hose with a wire to the bracket, and the second end attach to the water supply or pump. When you omit the pump in a barrel with a warm water, you can make pleasant water treatments.

You can still make a nozzle for a tropical soul using a container from disks as it. In his center you need to fix the plastic adapter, which is attached to the shower hose, and the central axis of the disks must be removed. Using sewing, make up the hole cover. All attachments are well a sealant. Such a nozzle on the bracket is kept with a thick wire or on a rigid tube.

If you have a desire to make a tropical shower, then you can use plastic pipes for this.

They need to bring water to them, pre-make a lot of small holes with a soldering iron, and then enjoy clinging drops. We like such water procedures to children.

But do not forget to pre-check the water in the containers from which it will fall into the shower, she must warm up in the sun.

And in order to make a stationary souls, you need to pre-pour water into the tank or in the barrel, which will be located under the roof or on the roof of the structure. On a warm summer day, the water here is well warmed, and you can wash it away. To be able to do this in more cool weather, then the heating system should be provided in such containers.

Dunny shower with their own hands

Before installing it, you need to make a shower cabin. If there is an opportunity, you can make it out of wood by installing this small structure on the basis. Put wooden door Or limit yourself to such a shower curtain.

There are more simple options. If you have a glued cloth, then use it.

Another option is to purchase fabric with impregnation or use the old awning or a tent.

If you did a fence from the corrugated floor and you have materials remained, then try to make a shower for giving of them. Metal pipes It is necessary to wear on the markup, pour them with concrete. When he dries, the trimmed sheets of professional flooring welded. One of them will become the roof.

If you have little wooden boards, then embody the option shown in the next photo on the right. And on the left shown shower, which is made by type of shoulder. So the materials for it will cost almost free.

When the shower is ready, you can install the water capacity on it. So that she better warmed, you can make a kind of coil from metal or from the hose. Then the water will warm up more active.

These and other homosexuals for giving allow the maximum to use the existing containers.

To be able to get warm water even when it is not heated by the Sun, use electrically heating. For this you can plastic barrel Locate vertically or horizontally. Then you will need to build on one side of the Ten, and on the other? Water bay fitting. Make a hole overflow to extra fluid It followed and you saw that the container is already full.

Now it remains to install the tank. Usually for this use the roof of the shower. You can put a flat tank made from iron or plastic. You can also make a canister for a soul from a metal or iron barrel. If you need to warm the water, then the heating element is mounted in the barrel.

Familiarize yourself with other examples of what can be done on panstone do it yourself.

Interesting homemade for giving with their own hands

Garden tools are very necessary for work on Earth. Often in the store sell not very high-quality sets. After brief use, the shovel rolled the handle, or the chuckles are twisted. Therefore, if you have the opportunity, try to make the tools with your own hands.

Take:

• cutlets;
• fragment of the plumbing pipe;
• trim from two-handed saw;
• screws;
• screws;
• fragment profile pipe cross section 3 cm.

Using a grinder, cut a piece of pipe. Taking the lever tool, you need to cut the segment of the pipe, break the sector and in the place where it will be a stalk, you need to work with a hammer to give future chipping the desired outlines.

To make the blade, take the cutting of the two-handed saw and draw the outlines of the future chipping. Tear two holes.

At the same distance and the same diameter you need to make 2 holes on the roast itself, and then cut a fragment from the two-handed saw.

Drill these holes with a drill and a drill created for metal work. Connect these two parts using rivets, which uses screws.

Now drill a hole in the upper part of the chief to then attach a stalk here.

Make a scoop that is very interesting to work on the beds. Then such homemakes for giving will allow you to find a very durable set of tools.

Spile the gluttony piece of the cutlery and begin to bleed it into a chisel.

Then, helping yourself with lever tools, break this part almost completely.

It will stay to work with a hammer that the scoop blade acquires the desired form. Using a felt-tumbler, draw the outlines of its working part and cut off the grinder.

With the help of an abrasive circle, clean the edge of the shovel and make them more even. Now handle the tool to the emery petal circle. This shovel will become such a brilliant.

Also drill in it a hole under the cutlets, then insert it and secure the screw.

Cover the cuttings of both tools with antiseptic, and then - varnish. Now you can use tools for destination. If you want, on the same principle, make a ripper for beds.

Very fascinating to create similar things for giving with your own hands. Maybe after you make tools, you will want to make a device on which you can dry part harvest collected. See how one gardener did.

How to make a dryer for fruits and vegetables?

See what materials you need to take:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws; screws;
• 2 door hinges.

But what tools need to be armed:

• bulgarian;
• welding machine;
• drill;
• stationery knife;
• roulette and marker;
• scissors for metal;
• hacksaw.

First you need to make the basis for the drying locker. Make a frame from square pipes. Horizontal and vertical racks are scolded so that the edges are smooth. And the tips on the connecting elements should be mowed.

The door here will be metallic. To make it, cut off from iron pipe 4 fragments and weld them into a rectangle. Then you need to strip this base with metal using screws with nuts and screws. If there is an opportunity, breed a steel sheet. To make a mount for the baking sheets, attach with back side Frame wooden bars. Take a self-tapping screw. In this case, each lateral is available on 4 wooden Brucks For 4 kids.

Absorber is installed in the dryer. Take metal sheets and paint it into black. Use heat-resistant paint. When it dries, put this workpiece on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, in extreme cases, steel. These materials are well carried out heat.

Now you need to see the dryer outside, make the roof transparent, from polycarbonate. Then the sun rays will be well penetrated here. You can also use glass. Close the ventilation windows mosquito net.So that insects do not fly here.

Attach the loop and lockable mechanism to the door. Attach the door to the place. See what a wonderful beautiful and spacious dryer turned out.

It remains to do the opponents. They must pass the air. First, roll the frames from bars, and then attach a metal grid to them.

Now you can cut fruit and watch your device work. Put the thermometer in the dryer to keep track of the temperature. It must be within 50-55 ° C. At a lower temperature, close the lower holes, putting a rag here.

In such homemade dryer You can dry not only fruits, but also vegetables, spicy greens, fish, meat, root.

If this device diagram of such a device seemed difficult to you, then you can make a dryer from a metal barrel. It cuts out a hole for the door, and the racks from the metal grid are inserted inside.

So that water does not register and it was better to ventilate, the roof is installed on top.

You can upgrade this device by installing inside the fan and an electrical heater.

If you want to make a lawn mower with your own hands, then it is also possible.

Turn into it the old washing machine, for example, this is.

And if you still have an old bedside table, then you will make a platform from it for the future of almost self-propelled device. But only the door is needed from the bedside table.

In the center of the engine shaft drill holes. Cutting knife Make out of the old two-handed saw. It is necessary to cut off from it in size of the desired form, cut out inside the deepening.

Attach two wooden stakes that will become handles of the mower. Do not forget to fix the motor and extension to it. Now you can experience such an interesting unit.

If you are interested in other homemade for giving, then you will be useful to see the next video.

Many interesting ideas is waiting for you in the first video.

And with steep homemakes from plastic pipes You can get acquainted if you look at the second story.

Making electronic homemakes with their own hands has gained popularity in the past century, when semiconductor devices appeared. With their help from the old equipment, it was possible to simply collect the devices necessary for everyday life. Today, repair and collecting equipment for home or giving, for a car or garage can also be solved at home.

[Hide]

Homemade devices for home and summer cottages

Electrics for home and summer cottages using electricity power can make every electrician. Most devices are created on the basis of the factory components and requires only school knowledge about electricity.

Electroshevychnitsy

The electroshalvant can be both horizontal and vertical. In stores usually sell vertical, and they perfectly cope with their functions after some refinement.

To create a horizontal barbecue, a heating element and a frame that resembles a brass is required. It is possible to make a heating element from a ceramic tube and a nichrome spiral wound on it. The tube is fixed through an insulating material in a metal housing. For assembling the case, drawings will be required.

Skelut mangal

An equally interesting idea is a skewed brazing brazier with electrical drive to rotate shampoo. By adding an electric motor to a regular mangal, you can get a great device that will prepare kebabs offline. To organize a shape drive, you can use a motor from janitors, from a washing machine or any other by 12 volts. With the help of a pulleys and belt or toothed transmission system, the shaft rotation is transmitted to the skewers, and the meat slowly turns over coals.

Homemade Wi-Fi antenna

Such antenna will improve the quality of reception and the speed of Wi-Fi at your home. According to the reviews, after it is connected, the signal level rises from 5 to 27 Mbps.

For manufacture, it is necessary:

• metal sieve or a small colander;
• wi-Fi adapter (USB);
• USB cable;
• drill;
• epoxy resin;
• photo truck;
• plastic clamps.

Manufacturing process:

1. In the center of the sieve we drill a small hole (14 mm) and insert a metal pin to it to secure the adapter.
2. Insert the connector from the USB cable to the prepared hole and fix it with an epoxy resin. The USB connector after gluing should be strictly perpendicular to the sieve plane, then the device works more efficiently.
3. Then, with the help of two screeds, "ears" are made through which the cable is attached.
4. The product is fixed on the photographic report. Drills in the antenna hole with a diameter of 12 mm and clamp the nut.

Necessary materials Insert the Shtyach B. drilled hole We glue a USB cable Fix cable Tripod Install an antenna using a tripod

Electric homemade garage

Consider several utility homemade projects for the garage.

Homemade chandelier

If you have weak light in the garage, the improvised chandelier will be very useful. For the manufacture of diving cartridge, a pair of angular cartridges, which are sold in a conventional shopping store are required.

Sequencing:

1. We are removed from the cartridges of the wire and fasten with a plastic screed. We get a cartridge into two lamps. It remains to be connected to the electrical network.
2. To do this, use the base from the luminescent lamp. Gently take the lamp, then we solder the wires from our design to the contacts of the base.
3. It is well insulated with them and attach the base of the cartridges.

The use of conventional light bulbs in such a design is undesirable - cartridges can fuse from heating.

LED device

An authentic LED lighting device can be another lighting option.

For its manufacture, you will need:

• old luminescent lamp;
• lED Strip Light;
• connecting wires.

Production sequence as follows:

1. On the case of the lamp is pasted into one or more rows of the LED tape.
2. Connecting wires are connected and the lamp switch is brutened.
3. The collected device is tested.

Dot welding machine

The desired device in the garage will be the homemade apparatus for point welding, the basis of which is the transformer from the old microwave. Prerequisite - The transformer must be worked in order not to rewind all windings.

The process of assembling the welder is quite simple:

1. A transformer is dismantled.
2. Secretly removed the secondary winding.
3. Two shunt are removed.
4. From thick wire (with a diameter of at least 10 mm), a secondary winding of two or three turns is performed.
5. From a copper rod with a diameter of more wires, electrodes for contact welding are manufactured.

Homemade point welding tool

Useful things do it yourself for fishing

Among the homemade can be found a lot of interesting ideas for use in hiking conditions, as well as on hunting and fishing.

Electronic alarm

An example is an electronic signaling device for fishing to a regular fishing rod or another tackle. A simple bunching device can be collected in just half an hour. It will take the old key chain and a filing and a strip of plastic with a thickness of 1-2 mm.

Animalizer assembly:

1. Keychain is attached to the rod.
2. The plastic strip passes on the fishing line and is inserted between the contacts of the keychain.

Now, when biting fish, the fish is drown, plastic crashes, the contacts will be closed and the key chain will work.

Underwater Camera for Winter Fishing

With the help of a homemade underwater chamber for winter fishing, you can see if there is a fish under the hole. And this simplifies the process of catching.

For the manufacture you will need:

• small chamber;
• hermetic box for the camera;
• small tv;
• car battery to power the camera;
• extension;
• inverter;
• lead for cargo;
• ultraviolet diodes for highlighting under the underwater shooting;
• superchalters, tape, sealant.

Assembly process:

1. Two holes make two holes at the top of the box. The extension cable is introduced through one. Through the second - the wire to which the camera is connected to the TV.
2. In the box, there are still a few holes in which the light bulbs are inserted. The wires from the light bulbs are soldered into one diagram (for example, with a parallel arrangement), which is connected to a power cable.
3. The holes are sealed with glue and tape for dense sealing.
4. The lead is melting and pour out small lumps of the elongated shape. Place them at the bottom of the box.
5. Customize the camera, connect to the cable. After that, it is neatly placed in boxing so that it has a clear direction forward and horizontally and passed a high-quality image. For stability, the camera around is plated with a soft material.
6. Torso is attached to the boxing (rope, belt), which will be lowered by the camera to the depth. For convenience, it is possible to connect it, and the camcorder cable with a TV with a TV to merge into one core, while gripping the tape.
7. Connect the power cable of the camcorder to the battery and test the device.

Homemade bait

A good bait for fishing can be made independently. This will be a device collected based on a simple multivibrator.

It will take:

• emitter of sound, for example, from children's toys;
• wires;
• a small plastic jar, for example, from under medicinal pills;
• electronic board;
• regulator with plastic rod;
• a piece of foam;
• batteries;
• loads for the float;
• volume control.

The bait assembly is carried out like this:

1. You need to solder the scheme and check it.
2. Two wiring soldered to the sound emitter. Then they are conducted on the body inside and connect to the board.
3. A regulator with a plastic rod is put in the lid from the jar.
4. From above on the board, a tight circle is installed from the foam, which separates the board from the battery.
5. In the lower part of the jars, weights are fixed so that the container is kept on the water as a float.
6. The regulator is set frequency and the sound changes.

Bait scheme - 1 Bait scheme - 2

Electronic homemakes for a car

Car enthusiasts create homemade with their own hands to improve external view And the convenience of using the car.

Electrical Self-Protection

For the car perfectly suitable simple homemade electrical probe. It can show the presence in the voltage circuit of 12 volts. With it, it is checked with the serviceability of the relay, as well as light bulbs and other equipment. You can make such a device from a syringe and LEDs.

Assembly scheme:

1. Two LEDs sold out opposite conclusions (plus one to minus the other and vice versa).
2. To one of the steps through the resistance of 300 ohms is joined by steel probe. To another spike - contact for the batteries.
3. The design is inserted into the syringe so that the dipstick comes out of the hole for the needle. Most of the probe is isolated by PVC tube.
4. 4 LR44 batteries are inserted into the syringe so that one of the poles connects with the contact of the LEDs.
5. A contact from the flexible wire with a crocodile clamp is supplied to another pole.

On the video tells how to make a syringe tester. Shot by channel Ilyanov.

Light switch

Pretty simple in the manufacture of a smooth light shutdown scheme in the car's cabin. Such electronics suitable for any car. In parallel, a small board consisting of a capacitor and diodes sold out the terminals of the cabin lantern. The drop in electricity voltage will occur gradually and create the effect of a smoothly extinguished light.

Car subwoofer

To make a car subwoofer with your own hands, you must first purchase a speaker. From its dimensions, it is necessary to repel when calculating the size of the case.

The simplest and successful for the trunk shape of the subwoofer is a truncated pyramid with a slope like the rear seats.

LED fogthorn

With your own hands you can make automotive fog on LEDs.

For creativity it will take:

• two tenrative LEDs;
• 2 lenses from the old projector;
• gaskets from plastic pipes;
• lM317T microcircuits;
• resistors.

Assembly instructions DIY:

1. LEDs are installed on pre-prepared aluminum radiators.
2. The design of headlights, lenses from projectors, gaskets and diodes on radiators is collected.
3. The fog is powered through current stabilizers on LM317T chips and resistors.

Automotive carrying

Very comfortable car carrying is obtained from a computer USB lamp. It is compact and connect the device to any place in the car wiring.

Production scheme:

1. From the USB plug, delete contacts.
2. In the plug housing we connect the wires of the lamp and car clips "Crocodile".
3. For fastening in the right place (even horizontally), a magnet is put on the plug.

As they say, there is no place in the garage. Men who spend a lot of time in the garage will agree that in some cases there is every minute and every square centimeter of free space. That is why garage cases master needs the competent organization of the working space. Here in every way they help and help various fixtures for storing building materials, work inventory, machine parts and other things necessary for the work. In order for your electronic, garden and garage garades always in their places, use the following devices:

• • stands;
  • shelves;
  • logging panels;
  • racks;
  • organizers for tools.

Also for clarity we offer homemade garage and homemade Masters DIY -YUTUB video will reveal all the nuances of the organization of the workspace and tell me fresh ideas.

Homemade at home with their own hands

Humid homemade man began to study from prehistoric times. Actually, all industrial processes are improved non-vertical or home development of folk craftsmen. We sometimes do not even think that we pay for those things that can make with your own hands. Schemes of homemade homemade It is easy to find on the Internet, and materials can be bought in a shopping store or find at home.

For example, of cardboard box and a piece of fabric You can make a convenient portable organizer for towels and other textile products.
The topic of storing all the little things is inexhaustible, fortunately, as well as the number of ideas. Successful ideas for decor You can also draw from ordinary things - let it be buttons or empty tin cans.
Steep shelves are obtained from ordinary boxes. How do you like this idea?

How did you manage to understand if you have detailed instructions It is not difficult to instill selfiemakers with your own hands at home. The video will help you comprehend all the nuances of this pleasant occupation. Useful advice, interesting ideas - Watch everyone must.

Homemade for giving and gardening with their own hands

At the cottage, a little free time appears for creativity and the arrangement of the surrounding space. therefore worth having a few fresh ideas at handto embody them on your own cottage plot. Catering homemade housekeeping at home with their own hands can be ingenious simple. From the primary materials you can make the unexpected and extremely useful things in the home everyday use.

Conventional pebbles turn into fairy-tale bells.From old kettle It turns out a beautiful flower pot.

Used tires - It has already become a classic in the world. garden figures. Stylish lamps for dacha interior - make yourself from the usual bank and candles (do not forget about safety technology).
- Gorgeous idea for a small cottage.
Homemade for giving and gardening with their own hands is often obtained by themselves, without unnecessary temporary and financial costs. Perhaps you did not guesses how useful for household Will be plastic bottles.Plastic bottles that came out of everybody can serve as the basis for incredible decorative flower beds. Funny "blooming" pillars Significantly decorate your country space.

Garden furniture with your own hands Successful homemade: photos and drawings

In the previous sections, we told you about homemade, which will become indispensable for the farm and home life. However, do not forget about the rest, in front of which, still, have to work a little. Cozy Chairs, different tables and shops, swings and hammocks - All this class-garden bliss can stay on your site. We offer to familiarize yourself with the photo instructions and drawings sadroom furniture. We picked up the best options for you.

Pleasant little things made by their own hands are most often becoming the main factors for creating a home coat. Many of them make it quite easy to make enough hands dexterity, a little fantasy and creative inspiration.

Interesting things assembled in our photo planting, not only please the eye, but also make life even more pleasant. Rather, let's start the review of fascinating things with your own hands.

Rug from stones

Let your interior be one step closer to nature. This cute rug made of a large pebble, made by their own hands, will become a bright natural decor - an excellent alternative to the traditional rug at the entrance.

Mug with golden accent

For a long time you dream to transform your favorite mug? Enough to postpone the conceived for later. Purchase a special aerosol with golden paint and rather start to create. Design options can be a lot - create health or follow original example on the picture.

Lamp lace lace

Like this lace lampshar You are unlikely to meet in any store, because such a masterpiece is the result of manual creativity and skill. The essence of the work is shown in the photo.

Paper cutting: Evening city on the shelf

This magic is at home at all is easy. This spectacular lamp in the form of a fabulous lock is cut out of paper. Such a technique can even with your child.

For crafts prepare the following materials:

• dense paper;
• scissors, pencil, ruler, eraser, bug knife, adhesive pencil;
• new Year's garland (better in batteries).
• the shelf for the picture (necessarily with a side, which will hold the picture).

Cut the edge of the layout to install it on the shelf. We deposit on the bottom of the garland and light the lights. Fairy backlit lock ready!

Kitchen organizer

Kitchen devices, with love made by you, look much more interesting to the shop analogues. With them, the situation is filled with a special warm atmosphere and comfort. Even such a simple organizer for cutlery, made of tin jars, will give the interior of some individuality and charm.

Mirror cardboard frame

Show ingenuity in the design of your dressing table. Instead of a boring classic mirror you can hang over it is something more original, for example, a mirror with an openwork frame from cardboard. Believe me, such a masterpiece looks with your own hands much exquisite to the store analogue.

Urban plot of cable

Add a note of unpredictability to your own interior. Long black cable, chaotic breathing near the white wall, can turn into the original minimalist urban plot on her background.

Vintage photo frame

Ancient frame from under a sworn pattern and simple wooden clothespins - excellent material for creating a unique photo frame in vintage style With a creative approach in design.

Charger in the box

If you are from those who have accumulated a lot of chargers, we have an excellent solution to aesthetic and at the same time a functional box for storage. She not only visually decorate the room and contains in order all devices, but also in place charges them!

Book with kisses

Creative surprise for a loved one is a mini-book with kisses. Listful pages, hearts are becoming more and more.

Accessory for toast lovers

Here is a nice toast can be sewn alone. Cute gift for occasion.

Shoes with cats

Add a little more bright colors into your everyday life. Old ballet shoes can be converted original, adding socks with charming feline faces.

And you will need the smallest: monophonic ballet shoes, brush, black and white paint, white marker, greasy tape. Next, all according to the instructions in the photo.

Soul Winter Accessory

Homemade decorative skates will again reminde the winter fairy tale and rest on the rink.

You wish to do the same, then prepare large pins, felt, cardboard, woolen threads for shoelaces, hot glue, marker and tapestry needle.

A little humor on a rainy day

Comic covers on rubber calicists will certainly not allow to be sad in rainy cloudy weather.

Charming spiny hedgehog

A stitched hedgehog from yarn can also be needles, just not their own, and sewing.

Funny abstractions

Feel yourself with an abstractionist artist, building bright emoticons from different miniature figures.

Cute kittens from cardboard for storing threads

Handmade brands collection

Baby Handbag

Why buy accessories for a child if you can make them with your own hands. Bag for a girl with a hare face looks very original.

Garland from ice cream

Create a summer mood, tied the garland from the most popular delicacy at this time - ice cream-horn.

Notepad in homemade leather binding

Stylish hanger

The loops of leather tapes nailed to the wall - an extraordinary minimalist hanger or shelf for books, magazines and other little things.

Magic vase

The magic atmosphere in the house can be created with the help of uncomplicated beautiful things, such as this vase.

Bracelet from rhinestones

Decorative letters for refrigerator or children's board

The letters from the training alphabet are a great idea for home decor. It will take only a very little gold paint.

Convenient headphone clamp

Spectacular flicker

A little bit of buttermate to the interior will give candles with golden and silver flicker. Such beauty can be done at home, using old candles and aluminum tape.

Bracelet-donut

This glorious bracelet in the form of a donut will have to the young fans of Homer Simpson. Here you only need a bright nail polish and a plastic children's bracelet, then it remains only to fantasize with the icing.

Optical clothes

A simple hat will significantly transform your daily style. It is enough to sew a few bright flowers in its edge.

Fine Neck T-shirt

Watercolor drawing sweatshirt

Beach dress-pareo

Headband

Braided scarf

A simple white T-shirt will become more stylish if you sew neat pockets with an interesting print.

More ideas for crafts are presented in the following selection of photos.

As you can see to please yourself and your loved ones, you do not need to spend a lot of strength and money. Your desire, creative approach and inspiration are able to work wonders. And the result of the work done with your own hands does not compare with the purchase of accessories and other stores.

Do you like to needle how? Tell us about your favorite creative masterpieces.