Each type of filters has its own cleansing resource. When it is exhausted, it is necessary to change the filling of the device or set a new more advanced model.
The reasons for replacing the cleaner may be different. The presence of even one of them is a reason for buying a fresh cartridge or a new device.
Replacement must be done if:
It is possible to determine which a good filter needs to be updated in several signs. They are common to flow, main, cumulative (type of jug) filters and nozzles.
Signal for replacement can be:
Track these features are sometimes problematic. The exhaust filter continues to skip water some time, but without proper cleaning.
Reference! To exclude such an option, many manufacturers are mounted on the devices special light indicators. The sensor lights up when the cleaner resource is exhausted.
The frequency of replacement of the filter element Depends primarily on the type of purifier.
Attention! In some cases, due to poor water quality, the filter filling comes into disrepair earlier. With small consumption and relatively low liquid pollution main filter It works up to 12-18 months.
Replacing the cleansing module depends on the type of filter. Each model is attached documentation in which it is reflected technical information Operating device. It also has an instruction for replacing the cartridge.
The process of changing the filter element in jugs consists of several steps:
On a note! Sometimes a new filter slowly skips water. To eliminate it, you must extract the cartridge, shake it and re-install it.
Vividly the entire process of replacing the cartridge is demonstrated in the video on the example:
Since the flow unit is connected to the water supply, the first thing to do is to overlap the water supply to the installation site of the filter. Then open the crane to lower the water residues and reduce the pressure on the plotting system.
It is also necessary to prepare the container in advance. (for example, bucket) for old cartridges. Of these, water will flow, so the container should stand nearby.
To remove the flask from the mounting case, you must click on the button and turn the flask counterclockwise. Cartridges are removed from the modules and fold them into the cooked container. Flasks and rubber seals are washed without the use of chemical detergents.
New cartridges are installed on the place of old elements. A little water poured into the flasks. This measure will protect the membrane from the damaging effects of air bubbles. Twist the flasks, open water and check the system for leaks.
Cartridges have the same appearance, but different filling. When replacing them, it is impossible to be confused by places.
Reference! If the cartridges are bought immediately in the flasks, the installation is simplified: it is enough to change the old copies to new ones.
In the next video, step by step is shown the entire replacement process on the example of the filter Aquaphor:
Before updating filters with multistage cleaning, it is also required to overlap the water supply, reset the pressure residue in the pipe and prepare a container for old elements.
The membrane component is changed separatelyWhen its resource limit ends. To remove the flask, you must remove the incoming and outgoing tubes. To do this, pull out the retainer and click on the ring. From the new cartridge remove the plugs. By reloading twins and tees from the old element, put them on a new one.
Connect into the tube connectors (up to the stop) and, raising up the ring, the retainer is inserted. The new filter needs pre-flushing at least 10-15 minutes.
Visual step-by-step execution instructions for changing cartridges in presented in video:
The main devices are installed by cutting on the pipe of cold or hot water supply. Despite this, in case of emergency or planned necessity, they are also subject to replacement.
They are updated according to the following scheme:
The video shows how to change the main filter installed in the bathroom:
Home water purification systems differ simplicity of maintenance. The principle of operation of filters of one type, but from different manufacturers in general terms is always the same.
Filters of such manufacturers, and other brands may differ from each other:
Changing insert cartridges occurs on a general scenario.
Attention! Some companies (for example, Geyser) produce cartridges according to the standard. This means that they are interchangeable with the sewage elements of other brands.
But not all manufacturers adhere to standards. For example, Aquaphor produces interchangeable blocks of individual design And it is impossible to replace them with an analogue of another brand.
To update the overall cleaning system in the cottage or country house There is always the opportunity to contact the help of a specialist.
The full range of services includes:
Attention! If it is not possible to refer to the firm that installed the cleaning unit, then you can find specialists by ads in the section of services or in similar organizations that offer filtering equipment.
In different regions, different companies have the price of such services. The cost imposes an imprint level and type of filtering system. The price variation ranges from 500 to 20,000 rubles.
By installing the filtering machine, it is important to monitor its condition. Calked cartridge must necessarily be replaced with a new instance.
Most cleaners intended for home use, have a simple structure. Replacing their filter elements does not represent a special complexity. Differences can only be in small features characteristic of each type of filters.
Filter (cleaner) over time clogs, therefore, it must be changed. It is important to understand how to change the water purifier. there is different systems Cleaning. Accordingly, a certain filtering technology is provided.
Before changing the water filter, you should know what manufacturers and models. There are a pair of filtering varieties (can you choose a jug?). When choosing, focus on the tap nozzle. It should be easy to use. It will be necessary to constantly change the cartridge. For most users, it is expensive, so often people buy a cleaner in the form of a jug. They deeply clean the flow water.
Their advantage in a compact amount, they can always be taken with you on the trip, to the cottage. In addition, you can buy a cartridge to obtain iodized or fluorinated water. The most important lack of jug cleaners in the magnitude of the capacity, so you can get from the filtered water no more than the volume of the container will allow. It is necessary to wait when all the water passes the process of cleansing.
More serious filtration systems are in demand. They are installed in the water supply system. At first it should be cleaned from large inclusions - sand, metal particles from pipes, dirt, and then from microbes, chlorks.
It is worth noting the next fact about disinfection. All people boil water to kill harmful chemicals. Therefore, some are still skeptical about the acquisition of the filter. They are quite satisfied with the boiling process.
Why do you need a filter and can I do without it? Boil - and all bacteria will die! However, it is important to consider the problem of boiling from the point of view of bacteria and heavy inclusions in the water. After all, boiling kills and useful and harmful bacteria. In addition, in a boiled fluid, the concentration of non-flutter combinations increases, because part of the fluid evaporates.
Undoubtedly, boiling exterminates the smallest organisms. Nevertheless, there are more disastrous elements in the water. And this is not an intestinal wand, but much more harmful to the body of inclusion. What is it? Flowing water includes an abundance of additives (salts, minerals, etc.). If you boil them, then the chemical structure of substances is changing. These modified elements enroll in the body together with twice boiled. Therefore, pay attention to how many times you can boil water. Only once. If you boil the same liquid for the second time, you will get heavy volatile inclusions, and specifically:
By type of cleansing composition:
For appointment:
According to the water taking method:
Remember that acquaintance with practical guidance Filtration systems are good, but not enough. The cleansing system is equipped with a cartridge. It can be a jug or a reverse osmosis system. Cleansing spare parts must be changed on time. The use of fluid passed through the cartridge with a exhausted working term will adversely affect the state of health.
When it is worth changing the cartridge:
When the process of changing the cleaner is over, for 10 minutes it is impossible to drain the treated water and drink it.
Clear water can not be called completely. It may include impurities, imperceptible to the naked eye. Mechanical impurities are harmful to humans, equipment and pipes. Harmful impurities can be postponed in the gastrointestinal tract. Such particles affect the walls of the pipe as abrasives. In the case there are filter materials, grids or other components. They are provided for holding such particles. The procedure is simple: it proceeds through the device and the cleaning component, and the inclusion remains.
With the help of coarse purification, water will be insufficiently purified. Especially for such purposes I use the fine cleaning option. Thanks to this cleaning method, you can, do not worry about the status of plumbing.
As a cleansing material use:
Difficulties with the replacement of working components does not appear: the service life depends on the volume of pure water or from the duration of use.
There are many filtration designs on the market. Therefore, it is necessary to attribute to the selection of the filter. How to choose a reliable treatment system? We recommend familiar with such manufacturers.
There are different cleaning systems on sale. One of the latest models is the stationary cleansing design of the Ultra Bio, which in the 3 stages perform cleaning from organic inclusions, however from microorganisms. Ultra Bio combines a couple of types of cartridges for limiting cleansing. At the same time, it acquires crystal purity and mild taste. The installation of the presented model is simple, will not require special exercises. It is worth installing a block on the pipe cross section cold water, twist the sealant. Replacing cartridges is performed on the outside of the device. The valve is used. Price from 8 thousand rubles.
The sewage designs of this brand differ in high efficiency, easy application. The company has long been manufactured a cassette for home filter jugs. However, smoothly included innovation - a model from the line of membrane cleansing systems - "Expert Barrier". This is a two-stage flask with different species material. At the 1st stage, the process of cleaning from heavy metals and chlorks. On stage 2, the neutralization process of poisonous elements occurs. Price from 3,550 rubles.
Simple and installation treatment plants are presented on the market. The company on the market for 15 years. The product range has expanded from cleansing cassettes for jugs to production complexes for scrupulous cleansing. The "Trio" cleaner is particularly fame, where the fluid passes the processing of 3 stages. This model is placed under the sink. Price from 12 thousand rubles.
The manufacturer is not so famous as other companies, not advertised. Company employees argue that the main advantage is not advertising, but in the high quality of instruments for cleaning flow water. And then really so. One from the most-selling modifications of this brand - Slim Line. The sewage treatment refers to the main cleaning type. Put the system on the wells. Price from 4 thousand rubles.
The company produces cleansing devices for more than 20 years. When the company was previously engaged only by industrial and manufacturing structures. The market presents a series of nozzles for the shower, a kitchen crane. From a functional point of view, the system works on the "accumulative" principle. This is a plastic dispenser in which two degrees of cleaning fiber and a small compartment for purified fluid are defined. Price from 5 thousand rubles.
Filters effectively cope with flowing water purification. If the service life of the cartridge has exhausted, it is necessary to replace it immediately. And then to deal with the question, how to change the filter for water. I Stage (mechanical cleansing) can be made of foamed polypropylene. For drinking filters The first type of polypropylene is selected. The cleaning level is not required to be higher than 5 microns. Such cartridges provide fine liquid cleansing.
Now in almost any apartment there are filters for purification of water. They include cartridges that are contaminated with time and cease to cope with their task. Therefore, you need to know how to change the filter for water.
Cleaning filtering devices Geyser and Aquaphor are the most popular in the population. Periodically, it is necessary to replace the cartridges in the filter. Everyone has its own bandwidth, it is expressed in liters.
Cartridge devices are considered the most common. To understand how to change the filter, you need to know its design. Often the cartridge has a cylinder form. It is made of filter material: activated carbon, polyethylene, etc. The method depends on the task performed by the device. Among them are distinguished:
The cartridge has a cavity cleansing water. It closes with rubber rings from the end side, which does not apply to mechanical devices. Seals made of rubber adjacent to protrusions present on the housing. They interfere with the passage of the source water into the channel purified. The lower part of the device is called the flask. It is attached to the top of the filter by carving.
For the first time the process will seem long. To simplify it, it is worth using a simple step by step instructions. Included with the filter there is a special guide. It should be detailed description Replace the water filter in the apartment.
However, for most devices, the procedure algorithm will be approximately the same:
The frequency of changing filters for water depends on the characteristics water water. It is not recommended to update cartridges too often, it will lead to unnecessary spending. A rare replacement will lead to the fact that the device will no longer function correctly.
Special attention requires coal devices. They have a rubber gasket. It can not be shifted to the side. The procedure for placing filter devices is important. IN membrane systems The first one must put the cartridge with the size of the cells of 5 microns. The latter should be an element in 1 micron.
Change the filter device of the main type can anyone. Periodically, it needs to update the cassettes. You can use the above instruction, but there is a couple of differences:
The manufacturer must be the keys to dismantle. If they are missing, it is worth purchasing similar. Now many are interested in how to unscrew the flask of the filter for water and how to replace the filters to unscrew the flask without the key. Specialists are not recommended to carry out this by other devices. Otherwise there is a risk of damaging the flask.
It is now difficult to find a person who had no water filter in the apartment. Urban residents often choose a device with a rough cleaning system. They perfectly clean the water from various contaminants. The most common are calcium salts.
The main advantage of the coarse cleaning filter is considered simple design. It allows the device to work as efficient as possible. Some do not know how to change the filters for water of this type. The main difficulty is unscrewing the supposed nut. Due to long use, it becomes one whole with a pipe.
Unscrew the thread is extremely simple. However, excessive application physical strength Hurt a nut or device itself. Then pollution fall into the pipe, and it threatens the appearance of many problems.
Refunction of the instrument should be made only by a cape or gas key.
You can clean the cleaning without dismantling if you get access to the grid. To do this, you need to carry out the following actions:
If WD-40 is absent, you can take lubricant for threaded connections. It must be penetrating. There is an alternative solution. Professionals are advised to put a rag on the filter connection, pre-dipped in kerosene.
Many of us have long been using such a water purification system as a filter. Despite the fact that water purification systems may have differences in the design, form, the purification method, which water passes, in essence they are similar to each other. The replacement of the water filter itself is a simple and affordable procedure for an unprepared user, which will not be difficult to master any work.
From this article you will learn:
What water filters require replacement and how often you need to do
How to replace the cartridge in the water filter
How to replace the filter in a stationary cleaning system
How to replace a coarse filter
If purified water requires you solely in cases of cooking, most likely you will fit the filter-jug. Simple and easy to operate, such a jug is able to provide water a small family of several people. For a relatively small time interval, the filter will clean the order of the alley of the liquid. Its main advantage is the simplicity with which the filter is replaced. Cassettes for a similar filter relative to inexpensive, searching and replacing cassettes does not require any effort from the filter owner.
Depending on the manufacturer of the jug, the overall resource of such a system may vary in the range of 150-400 liters. Cartridges, as well as the filters themselves, may vary in quality. Replacing cartridges with which water is cleared, can be made even a child. The main disadvantage of such a system is considered a small amount of fluid issued by the filter at a time. Clean water will be limited to the sizes of the jug (the maximum of 2.5 liters), so that it is not possible to fill the large pot immediately. Add here what to wash and wash you will have to be all the same untreated water. And water from the crane, as is known, has a high degree of rigidity.
The filter-nozzle used for the crane has a bandwidth not exceeding 200-500 ml per minute. In addition to restrictions on the volume of purified fluid, the nozzle does not use high demand due to its design. Design "Nozzle-Crane" like not everyone. The system of this type will require the selection of the container, into which water will later be collected. Most of these filters do not have a special collaboration system and therefore do not allow the user to independently adjust the power of the jet. If you need water to simply wash the dishes, then you will have to disassemble the system.
Compared with all previously considered options, the flow filter takes one of the most successful and demanded positions in the market. Systems of this type are called desktops in everyday life, sometimes you can meet the name "Filter under the sink". This filter is connected to the crane located on the sink. Connection will require a plumbing hose.
In just one minute, water can be obtained in a volume of up to two liters. It can be used in the process of cooking and drinking. The cleaning system of this type has a sufficiently serious resource of up to 4000 liters. Replacing the filter for water directly depends on fluid flow. For example, a regular family in the composition of the three or four people will be replaced after 1.5-2 years.
It should be noted that such a system is infrequently chosen for small-sized apartments, because for fastening the system, a place will be required. The main inconvenience for the consumer is often unsuitable for home crane sleeves, which are included in the bundle of the cleansing system. In this case, the bushings will have to select and acquire additionally.
One of the most convenient for family use. By appearance It resembles a cylinder inside which filtering elements and a container for collecting clean water are placed. This system is traditionally installed under the sink.
For fluid output, an additional crane is used. Despite the relatively high cost, such a filter has gained popularity among consumers. The thing is that the replacement of the filter is a simple and understandable process, the filter does not require preparation before use, and its resource contributes to rapid payback in the process of using clean water.
Externally, the central filter resembles two flasks. It is inside of them and filter elements are concluded. A feature of the system is the method of its installation: the insertion of the system is made after the meter, in the place where water enters the apartment from the central water supply.
It is known that the water entering the apartment along the central water supply line or the well can not boast of the necessary level of cleaning. Impurities that contain water require additional filtering. Household devicesintended for water purification, selected depending on the level of pollution.
By type, they are divided into mechanical, ion exchange, membrane and adsorption. If water passes through a whole system, representing a combination of filters, we get a liquid with a high degree of cleaning. After the cartridge has extended its resource, the filter is replaced for water.
Replacing water filter is usually carried out at once for several reasons. The main one is a cluster in the materials of the filter of harmful substances that contain unfiltered water. If their number exceeds permissible normsThey are able to get into the water again, worsening its quality, and therefore damaging human health. The contaminated filter becomes a favorable medium for breeding bacteria. Determine the presence of filter contaminants simply: you can note the low, compared with the initial, pressure.
Replacing the filter can be made on the basis of various indicators. So, in the case of a transparent flask, pollution can be assessed with a naked eye. Some devices are equipped with special devices that help determine the time to replace.
For convenience, manufacturers make special pointers that help to replace the spent cartridge on time. Replacing the water filter has a direct connection with the intensity of using the filter and water pollution. Water coming to us from the central water supply, despite the pre-clean, has in its composition residual pollution, which are subsequently removed by domestic filters.
At the same time, water from the well or well differs from tap larger pollution. If the filter is used to clean such water, it should be replaced much more often, every two or three months.
In multistage filters, the main load falls on the first, initial stage - it is here that water passes the primary cleaning. If the replacement of the first filter should be made every two months, the remaining cartridges can be changed once every six months.
Replacing the filter for water, video of this you can find on the Internet on the links below, in the usual case starts from overlapping or turning off the water. If the system is equipped with a separate crane through which water flows, it is blocked; When there is no separate crane - water overlaps completely.
After the water is disabled, you can move to the opening of the filter flask. In order to reduce the internal pressure capable of preventing the process, the pressure reset button is used. In the absence of such a button, you simply open a crane through which purified water is supplied.
Next, the filter is replaced. From the opened cup, the spent cartridge is made. Additionally, it is recommended to check the sealing gum. When saving the elasticity of the gum can be left without replacement. Additionally, rubber bands are flushing. If you felt that the seals became rigid, they are recommended to replace them.
Clean flask is ready for the immersion of a new cartridge. After the cartridge is installed in its place, the flask is closed using a special key.
If the replacement of the filter elements is carried out in the membrane filter, the flask must be filled with water. Thus, you will protect yourself from the membrane damage to air bubbles. The remaining structural elements can not be filled.
Any filter replacement must end with the tightness of the compounds. To perform the verification, discover the crane, look carefully - whether water flows. If the leakage is detected, the flask should be tightened again. If it does not help, check and replace the seals.
Now that the cartridge is installed, water must be drained. Open the faucet and drain over 10 minutes. After the water is somewhat, you can be sure that the liquid will not fall dirt and dust from the filtering materials of the system.
Replacing the water filter, the price of which is somewhat higher than the average (it includes constant type filters), it also does not constitute any difficulties for the user. Replacement should be made every year or once a year and a half. At the same time, the replacement occurs on the following chain of actions:
first of all, a locking clip must be filmed;
in order to disconnect the hose, click on the ring;
remove the filter itself from holding his brackets;
we proceed to disconnect the hose leading to the filter membrane;
we produce filter replacement procedure reverse osmosis;
making the membrane assembly;
we produce the installation of a new filter;
at the last stage, reiterate the hose.
Replacing the filter for water, video about which you can see by clicking on the link, the procedure is available even for an unprepared user. As soon as the replacement is completed, the system can be used in operating mode to obtain clean water.
Coarse filter - system capable of retaining large mechanical particles that contain water. The device is equipped with special filter elements. Externally, they are a small mesh and polypropylene bobbin.
All products of this type can be conditionally divided into several basic species, among them:
Here the main filtering element is a grid. It places in the system housing. At the same time, the mud itself is located vertically or at a certain angle of inclination.
Filter of rough cleaning, like other similar systems, needs a periodic replacement. The replacement is made in several main steps:
Water in the house is completely disconnected (both hot and cold). In order to reduce the pressure in the pipes, the cranes are enough to leave open (before the end of the replacement process, it is important to close all the cranes again).
We unscrew the old filter using a conventional wrench. If the clamps are placed on the walls, remove them.
Remove the old seal left from the filter removed. We wind up a new isolent.
Using a wrenched wreck, a new filter to the wall. Make sure that the gaskets remain in their place.
Open water. We check whether there are leaks.
Replacing a coastal water filter is not always necessary. This system can be cleaned by implementing the following sequence of actions:
Water in the house overlaps.
Using the adjustable key, we unscrew the lid of the mud. If cleaning occurs quite rarely, some efforts will be required to remove the lid.
Give the grid and carry out washing, for this is used flowing water. It is recommended to use a toothbrush to clean, so you can easily remove all the contaminants even from the smallest mesh holes.
We install the grid in your place, we wind up a new isolate on the thread. It is also recommended to install a new gasket, placing it between the mud and the lid, so you can forget about leaks. Using the adjustable key, spin the lid.
Now you can turn on the crane and check whether the leaks appeared.
It is worth noting, the filter replacement is sometimes not such a simple task, as it may seem first. In order to avoid unpleasant situations, it is recommended to contact the specialists.
Biokit offers a wide selection of reverse osmosis systems, water filters and other equipment that can return water from under the tap its natural characteristics.
Specialists of our company are ready to help you:
connect the filtering system yourself;
deal with the process of selecting filters for water;
pick up replaceable materials;
eliminate malfunctions or solve problems with the involvement of installers;
find answers to your questions in the telephone mode.
Trust water purification systems from Biokit - Let your family be healthy!
