The master will show the selection interesting ideas On the use of grinder that will help expand the functionality of the tool and make it more convenient. See the selection of 5 options and choose what can be done based on your experience.
1. The screen shows the mounting saw. This is not factory production. Such homemade has two clamps - horizontal and vertical. Thanks to the duet of the presses, no detail jumps out from the place - be it corner or pipe. In addition, there is a movable limiter for serial cut parts of a certain length. Excellent device that is easy to assemble hands.
2. Grinder may not be positive, but no one has not demanded from it. Conference in reliability and practicality. The most interesting thing is that the manufacturer does not use the welding machine. In other words - no detail is welded. All tightly on the bolts, which makes it easier to assemble the design.
3. From the old table, you can make a home mini pail. Attention! In the fragment of this video, a flawed machine is shown or removed from it. protective casing. Questions except this and others, there are both gloves. See TB when working on a panel.
With the help of the power regulator, you can change the revolutions of this homemade. Bulgarian is attached under the table in three places. Thus, eliminating any disk vibration. But we note, it is just an idea, and not a ready-made unit. Making such a homemade, take care of the safety primarily. It is necessary to close the unused part of the disk. For convenience, expand the table and install the guides. 
3. Modest option for cutting molding products. This homemade with the presence of the guides can cut the metal under 90 degrees, 45 degrees. Removable guides themselves. What makes it easier to transport and storing the saw. This homemade uses at the same time two options for returning the cutting disk to its original position. This is a counterweight in the form of dumbbells and springs. You can use only one of them to choose from.
4. There is another idea - to do milling Machine From the Bulgarian. It can not only cut off on it, but also make samples. Cutting metal will not be cut, but a milling disc. Bulgarian is attached simply. It is spinning with his handle through the corner walking along the table. If the option seems simple, you can develop the idea and come up with something your own. 
5. If the pipes are cut into a large diameter, then faced the problem to cut metal into one dive, as the GEM gearbox always prevents it. Homemade will help solve the problem. In addition to the mounting or to the pendulum saw, the bed with furniture rollers helps to lean and fix the pipe. At the same time, making a small propyl, thanks to the rollers, it is easy to twist and cut off all over the diameter. 
zen.yandex.ru.
From the ushm, the craftsmen make various devices that expand the fleece functionality and simplify the work.
And make them quite easily. 
It is useful when you need to make many different segments.
The easiest option is to a metal base to weld the two guides from the rectangular pipe.
From the same pipe to make a handle to which the Bulgarian is consolidated. On the basis, you can make a guide from a corner for cutting blanks at a certain angle. 
Photo: Avto Class (YouTube.com) Some masters make such racks from bars and plywood. Construction is simple and reliable. 
It can be used for rust removal, paint removal from walls, polishing, etc.
Plus this homemade is that the surface is always processed at one angle and with the same effort, without leaving the deepening in the dentin. 
A simple device for smooth saws of wood and sheet metal.
For wood, specialized saw blades with three teeth are used (do not install discs from a conventional circular saw). 
It is made of metal plate and stud, which is attached to the hole in the center of the circle. 
Ribbon moves the wooden cylinder, inside which the nut for installation on the shaft of the grinder is glued.
The device itself consists of two square pipes different sizes. Inside a larger pipe inserted spring, with which the tape tension occurs. 
A bolt is fastened to the wooden base of the Bulgarian, the rear part is installed in the mount from the bar, additionally can be fixed by a clamp. Used to sharpen tools and grinding various surfaces. 
zen.yandex.ru.
There are insane ideas for the Bulgarian like using it as a lawn mower. You can also use it to build a quadcopter, cycling, pumping water and more useless, but extremely exciting cases. We will consider those options for using a grinder that is really useful and sometimes help to get out of the position with a lack of a specialized power tool.
1. It happens that it is necessary to smoothly cut the iron sheet. With this device, it is easy to do, even a ruler. 
2. It is not always at hand sharpened to refuel the bore. But with the help of the Bulgarian, it can also be done. 
Homemade cutting machine From the Bulgarian (USH), which can be done without any problems and install in the garage - this is a solution to problems in wood or metal for those who often hold this tool in their hands.
Adaptations from the Bulgarians, which can be made with their own hands are able to make it much easier to relieve this tool.
The main advantage of the Bulgarian is her mobility. But in some cases, when the processed item is not fixed, and it is not possible to hold it due to the lack of an extra pair of hands, natural vibration appears. Such a phenomenon can lead to sudden destruction of the work disk, What is fraught with injury when the fragments are divided.
If necessary, cut off the grinder several parts of the same length, and even strictly on perpendicular, it arises difficulty in controlling the disk passage and accounting for its thickness, to comply with the specific slices of the cut part.
In addition, there is always a danger of the occurrence of the opposite strike in the process of cutting, which can also lead to injury.
In order to eliminate these inconveniences in the work, both in the wood and for metal, you can use adaptations from the grinder, for example, a homemade stationary cutting machine from a grinder.
The main advantage of the cutting machine from the Bulgarian is his mobility
If available, the angular grinding machine will work as a tracing saw, which is much more convenient and safer.
There is a very simple way to create a device from the Bulgarian, which will be much simplified and will save force when working on a tree or metal. In order to make it homemade MachineThis will require only a few working hours and the simplest components:
The design assembly is a pipe, To which the plate with holes for fastening the grinder is welded, it is also a lever (handle) for raising and lowering.
The end of the pipe on which the ESM is installed is connected through the swivel shaft with a corner, which is fixed on the desktop or simply on the floor. In the same part, a spring is installed to facilitate the lifting of the lever.
The main complexity, with this variant of the bacal, is to properly fix the tool. The saw (disc) should be descended and climbing along the trajectory strictly perpendicular to the base (angle with a swivel shaft) and exclusively in the same plane (without backlash).
Read also.
A more complex variant of adaptation from the Bulgarian, which makes it possible to make accurate work. For its manufacture, you will need the following components:
Before starting work, you should draw up a plan scheme with parameters that are suitable for specific accommodation conditions and the type of work performed. It can be copied with an already ready-made adaptation from the Bulgarian available, or explore all the proposed options posted on the Internet and choose the most suitable.
First, it is necessary to make a frame that consists of two frames interconnected on a swivel shaft. Thus, they can develop as a book cover. A sheet metal or plywood sheet (chipboard) is fired on the lower frame. Upper frame must have fastening for fastening the grinder, which will reliably hold it in a stable position for any loads.
To fix the parts being processed, when working on a tree or metal, you must provide a fixing device. Such may well be the usual clamp. It should be welded to the bottom frame.
For easier lifting of the upper frame, as well as to autonomous fixation in the upper position, it is necessary to install a fairly powerful spring, which will be able to raise the weight of the upper structure (frame with a grinder).
For measurements and setting exact parameters, a ruler with a retractable limiter is suitable. This will allow you to be confident in the correctness of work.
In order for both hands to be free when the machine is turned on and off, it is recommended to install a foot pedal (switch). To do this, through a low-voltage relay (12V) power is done to the grinder. This measure is necessary to improve the security and convenience of control.
Angle grinding machine is a very universal tool. In case of acute need to make a milling machine from the grinder with their own hands will not be burdensome case, since The design is very simple and does not take up much space. At the same time, it is not regularly used for milling work on metal regularly, but as needed.
Necessary materials:
Each wizard always has its own workplace. As a rule, this is a table or workbench located in a room in which noisy works can be carried out (garage, shed, etc.). It is such a table that will be needed to fit, which will allow milling work on metal.
On the edge of the left side angle of the desktop, a curved plate for fastening the grinder is installed at the right angle. The principle is that the fixed tool must act as the edge of the table smoothly as the disc need for free rotation.
For this, the medium-sized disk is selected, and in the future without moving the grinding attachment, a larger or smaller diameter cannot be used.
After the Bulgarian is installed and fixed, the profile tube is installed. It should be cutting down a depth 2, 5 cm and 2 mm wide greater than the thickness of the working disk (1 mm on each side). The pipe is welded to a corner, which, in turn, is fastened on the table in front of the brandy mounting plate.
Installed fasteners should be arranged in this way To hang from the edge of the table, Bulgarian his disk went into the propyl profile pipe.
Thus, it turns out that when rotating, the disk is surrounded from three sides. profile pipe To the depth of 2, 5 cm. This allows you to work on the metal, holding the workpiece in the hands and laying it onto the stand (profile tube).
Of this kind homemade installation It can work and as a cutting saw, and in some emergency cases, it may well be replaced with a lathe.
But not for metal, but on a tree, if you provide for the presence of the cutter and the moving element of the billet fastening.
Since the speed of rotation of the disk is much larger than that of a conventional disk saw, then when hitting a solid, a reverse strike is possible.
Before you start, you need to make a work machine for several minutes in idle mode, in order to ensure that the disk when rotating has enough space and does not cling to any obstacles.
Greetings to all readers and site visitors!
I probably will not surprise anyone if I say that today Bulgarian is one of the most common tools among the masters of varying orientation.
The correct name of this tool is an angular grinding machine, in the people - Bulgarian.
In this article, I will tell you how to make a device for the grinder to the ambulance hand.
We will need a minimum of tool for work.
Also need material.
270 × 28 × 35 mm - 1 pc. Frame detail.
120 × 60 × 23 mm - 1 pc. Lever.
30 × 30 × 420 mm - 1 pc. The carcass amplifier.
300 × 120 × 2 mm - 1 pc. The basis of the device.
You can use a textolite plate at least 3 mm thick.
55 × 30 × 75 mm - 1 pc.
60 × 60 × 45 mm - 1 pc. Bulgarian fastening.
3 × 20 mm - 4 pcs.
3 × 35 mm - 2 pcs.
3.5 × 16 mm - 2 pcs.
Preparation of a platform from a duralie plate.
✓ Hold a plate size of 300 × 120 mm.
✓ Swells six holes Ø4 mm with a deepening under the hats of self-tapping screws. These holes are needed for mounting the corners, bar and handles.
✓ Durable corner 30 × 30 × 420 mm make an angle.
To do this, make a cutout in the form of an equilateral triangle in one of the shelves in order to bend it at a right angle of 90º.
✓ Read the handle (120 × 60 × 23 mm) with Bru (270 × 28 × 35 mm) using a screw 3 × 35 mm - 2 pcs.
✓Cedded M-shaped parts and a duralst plate collecting together.
Everything is attached by self-draws 3 × 20 mm - 4 pcs.
The base is ready.
Final assembly of adaptation for a grinder
✓Tery need to install metal corners 55 × 30 × 75 mm - 1 pc.
60 × 60 × 45 mm - 1 pc. On the resulting platform for fastening the grinder.
Note Corner 60 × 60 × 45 mm We must definitely bend a bit from 90º to 60º.
Otherwise, the Bulgarian does not fix.
Bulgarian is attached to the corners on the one hand with the help of its own handle, and on the other hand, using a bolt with a controlling M 8 × 20 mm.
The locking is necessary in order for the bolt not to unscrew the work on time.
The knob is not needed, because You keep it with your hand.
That's all - the cutting device with a baccoon is ready.
I think that many will have a reasonable question: "Why make such a device when there is a manual electric disk saw?"
I agree with such a formulation of the question, but this is if such an electron is often used, then you can also purchase. And when from the case of the case, it is better to have such a device.
By the way, such a device can be used not only, for example, for
Bulgarian is a useful and versatile tool. It is suitable for cutting metal, stone, tiles and, grinding surfaces. However, sometimes there are situations in which a stationary machine will be suitable for these works. It is good that using certain adaptations for the grinder, it can be turned into a cutting machine.
Search for a finished machine corresponding to your requests in stores will not be difficult. However, the likelihood of finding a construction that hard fixes the grinder and does not hang out during operation, since they are all made from Durally. For this reason, many prefer to produce various adaptations for the grinder with their own hands.
When performing construction and mounting work A large number of different tools are used. Most often used Bulgarian. The main task for which it is used: cutting metal; Treatment of building materials.
If you still use nozzles with this tool, you can expand the number of options for using it. In particular, by applying this tool with nozzles, you can perform high-quality grinding Boots of blanks. They will be cleaned of foreign inclusions. Bulgarian nozzles can be purchased in the store. But if you do not have a desire to pay money, then you can make them with your own hands.
In some cases, this tool is used as a stroborosis. With his help create grooves For laying pipes and electrical wires. To use a grinder in such quality, you will have to perform some manipulations and enlarge standard width Protective casing. In addition, it will be necessary to make a slab for support.
This tool can be used with one disk or immediately with several. If the Bulgarian is used with two disks, then it is necessary to make some changes to the attachment node of this tool. After that, the Bulgarian can be used in standard mode.
Often happens that during repair work And the need arises in the performance of the foundation of the parts, access to which is difficult. In such cases, the masters most often resort to the use of self-made adaptation for the grinder in the form of a special nozzle, thanks to which the disk of a small size can be carried out for the dimensions of the grinder.
In this case, the rotation will be transmitted with special belt transmission From the main drive. Using such a design, the cutting of materials cannot be produced. However, it is possible to remove without problems from the surface of the scale of scale. It often occurs on the surface of welded seams.
IN currently The market offers a large number of nozzles for such a tool like Bulgarian. Their use allows substantially expand application options This tool. If we talk about the most frequently used nozzles for the grinder, then the following can be allocated:
When there is a need to use a grinder for specific tasks, in this case, many masters make a choice in favor of finished nozzles. They can be purchased without any problems in a construction store.
The cost of devices is not very high, so everyone they can afford. With the search for these nozzles of difficulties does not occur. However, despite all this, many people are still solved on the manufacture of nozzles for the Bulgarian with their own hands.
If you decide to make nozzles for this tool yourself, then before proceeding to work, you must prepare the following tools:
Before you begin to work, it is necessary to cut the plate from the metal. After that, you need to make an angle out of it. To make a conceived, you must first make triangle-shaped In the shelf of the workpiece. And when it is done, the workpiece must be bent at right angles.
Next, in the design of the plate follows drill six holes. The diameter of each of them should be 4 mm. Subsequently, these holes will be installed in these holes. With their help, you can fix the handle, corners and timber. In all holes there must be special notes under the screws of the screws.
For a reliable fixing of the arch of the bar of several sleds. Fasteners used during this work must have dimensions of 3x35 mm. This will make it possible to get the part of the M-shaped form.
After that, all elements with a plate are compiled into a single design. The created tool device must be fixed using 3x20 mm screws.
So, the basis of the future design is made. Next, you will need to perform metal Corners Installation. You have in stock there should be several such elements. They must have the following dimensions:
Draw attention to the fact that the first corner should be dispersed up to 60 degrees. If this is not done, then to achieve your main goal - to fix on the grinder, the manufactured structure will not work. When the installation of metal corners will be completed, they are fixed directly to the tool itself.
To connect the tool and structural elements, a separate handle on one side is used, and bolts with nuts, on the other hand. The latter are necessary in order for the work during the work, unscrewing the design screw.
If you wish, you can abandon the installation of the nut on the handle, as it will stick to the master of the wizard when working. On this, the work on creating a design for cutting can be considered completed.
Often, the grinders are used with the bed. They are used mainly to make the wizard certain works on cutting materials and blanks with less physical effort.
For everyone, it is obvious that it is extremely difficult to keep a tool with a lot of weight, a few hours. Therefore, to facilitate your work when performing operation, many masters made special deviceswho call the beds. When the Bulgarian is equipped with such a device, then the cutting work can be performed by using only one hand.
To make the bed, first need make a wooden box. You can do only with one side on which the instrument will be fixed. All other walls can be removed, and instead of them to attach the legs of a special design.
But in order to achieve the effectiveness of the use of a grinder with such a device, some changes should be made to its design.
First of all you need to perform dismantling of the casing of Bulgarian. After that, you need to wear a disk to the tool. When this action is performed, it must be pressed to the side wall of the device.
It is necessary to put a mark where the gap for the hid or disk has been made. Its width should not be too big, otherwise foreign items when performing work can get inside the design.
If desired, the gap can increase. The need for this occurs in cases where it is necessary to replace the nozzles without performing the analysis of the entire design. Samples of wooden bars can be used as reference elements. After that, you can start performing work on sawing blanks.
When maintaining construction and installation work, an important adaptation for the Bulgarian is the transport. It is especially indispensable when working on the processing or cutting of metal profiles is performed.
Resorting to the use of such devices, you can easily calculate the corners of cutting blanks. And this positively affects the speed and quality of the work performed. In addition, such a device is suitable for cutting metal profiles.
Having made the transporter for the Bulgarian with their own hands, you will disappear by the need to purchase special tools that are quite often expensive and possess large dimensions. For industrial use, homemade transportation is not suitable, but for use at home it will be an excellent replacement for store fixtures.
The first thing to do is install guide corner, equipped with a special overlay, on the tile. Use a similar overlay in order to eliminate the slip of the fixed billet. Therefore, due to it, the displacement of the element will be excluded.
Then you need to close a blank to the shelves. After that, the user must set the cutting angle to him.
Next, you can move to the cutting material. When performing this actions, it is necessary to take into account that when picking it is necessary to put pressure on the disk slightly. You do not need serious physical efforts.
The homemade transporter for the Bulgarian has a design consisting of the following elements:
Note that it is difficult to make your own hands. Therefore, if you are inseparal to handle such a task, it is better purchase in the store Ready models of transportation.
Bulgarian is a fairly popular tool from builders and repair professionals. With it can be cut various materials and process blanks and details. However, sometimes performing specific operations. Therefore, experts acquire special nozzles for Bulgarian. They can easily find in stores.
The use of such devices allows you to expand the number of uses of this tool. However, it is not always necessary to buy them in construction stores. If you wish, you can make them with your own hands. To do this, you just need to have free time and know how to make the nozzles for the Bulgarian.
Bulgarian - a tool with a plump character. She cuts, and grinds, and cleaned, but it does it at such high speeds that sometimes it is in the hands of Hands! Therefore, it is not necessary to talk about the high accuracy of work. Rack for the Bulgarian - just what is needed for the taming of the plump!
Why do you invent a tripod for the Bulgarian if you can do everything with your own hands? It is possible to make something, that's just the quality of the cut, its evenness and accuracy will remain at a very low level. Well, in no way the master does not cope with the tool that the number of revolutions is greater than the human eye is capable of catching. Here for such cases and there is a tripod for the Bulgarian, with their own hands made or purchased in the nearest construction store.
The convenience of the device lies in the fact that they can be used if necessary, although many masters in order not to mess with the next installing tool to the tripod, buy for these goals a separate Bulgarian, good, models that are suitable for working on tripods are not so expensive. In any case, it is cheaper than buying the cutting machine. Most users note that the rack-acquired rack needs if not in full, then in partial refinement.
Models of Chinese origin are at all at all - mainly, they are made of sheet metal by stamping. Light parts from the tool vibration scatter over time who is where, and the design itself turns out too easy and unstable for such a machine. So it turns out - make a device for fastening a grinder much better with your own hands? Judging by the number of various drawings, tips, master classes that can be stumbled in the network, the answer will be affirmative!
Before proceeding with the review different designsIt should be noted that all of them are designed to work with grinders adapted for discs to a maximum of 125 mm. Already the 230th Bulgarian is fraught with a rack, since it often has to remove protective covers, besides, the operator behind the rack is against the rotation of the disk. Neglect the safety technique in the case of working with the corner grinding is very and very dangerous!
When designing the machine, use only high-strength materials for protective covers. Many for amenities use plexiglas so that the protective screen does not cover the overview, but the use of materials that can form fragments from impact, is strictly prohibited! It is better not to make housings from undergraduate materials, but to purchase finished products that will provide the best protection.
Consider the design of the grinding machine, which allows the operator to be on the side of the rotation of the disk - just in the zone where the abrasive fragments, in the event of its destruction, will not be able to fly. Most drawings are designed for the creation of metal machines, by welding different parts, however, the described bed for the grinder is made with their own hands from the wooden elements, which much speeds up the creation of the machine and makes the process possible, even if you do not have a welding machine.
You will need a wooden box or boards in order to put it out, hammer, manual or electric jigsaw, drill, fasteners (ties, bolts), door loops. If there is a good, strong wooden box, great enough so that you do not have to bend very low, you can save a lot of time by taking it as a basis. If you spoil the drawer is reluctant, get it like a similarity: it will be enough to make the side to which you later fasten the grinder, and the top of the machine, and the missing sides of the box are compensated by legs.
The protective casing and the handle with the grinder at this stage should be removed. We have to do in the top of the box of the gap for the cutting disk or other nozzle. To do this, put the disc on the grinder and lean the tool to the side wall, press the width and the length of the gap. It should not be too wide, so that when foreign items get into the disc.
This precaution will have to donate if there is a constant need to change the disk - with a narrow slit you will have to disassemble the entire design, which will take too much time.
For reliable fastening of the grinder to the wall of the box, two bars are screwed up - one supports the tool near the base, the second serves for the support of the grinder directly near the disk. A metallic eyelet is screwed to the upper bar, which replaces the handle. All that is needed is to spin the screw - if the device is a hole through the hole, you should not turn the screw deeper than the thread length. Additionally, along the entire length of the case, the tool should be fixed with screeds, for which we pre-schedule and drill the holes.
Grinding machine is practically ready! It remains enough to provide for the possibility of raising the processed blanks relative to the disk. To do this, you can put almost additive to the disc. wooden shieldwhich on the side is attached to the loop so that it can be removed if necessary. To fix the shield, you can make a cheek or lock. Complete the design with protective panels, and if there is no such possibility, then when working, be sure to wear a protective mask that closes the entire face. Try with the apparatus turned on not to be in the area of \u200b\u200bfragments of fragments.
To cut metal blanks from the tree will not work. There will be a thorough detail here. First of all, the platform that should turn out to be sufficiently heavy to absorb vibrations from the tool. Alternatively, the platform is fixed on the desktop bolts, which completely eliminates the movement of the machine during operation. To realize the simplest design, you will need sheet steel, metal corners, bolts, drill with metal drills, spring.
The second important element of the rack is a hinge handle to which the tool is attached. Options for its manufacture set - it is and simple design Of the two metal plates, interconnected, and use already ready-made solutions or details. For example, if you often have to work with grogs, you probably have been lying in the garage of the details from the tools that you use for in case of need. So, instead of a hinge, you can use a gearbox that should be unscrewed from the housing and fasten using a bracket and bolts to the platform.. A handle is attached to the spindle, and already on it and fix the grinder. The handle is recommended to do with the focus under the bottom of the grinder, as well as provide a return spring.
With the help of metal corners on the platform, you can do various limiters at your discretion, with which it will be convenient to fix the cutting blanks. Here already every owner itself and the master - someone builds additionally vice for greater accuracy, someone costs fitting on the eye. As in the case of a grinding machine, do not neglect the security, if your design does not provide for the ability to fasten the protective casing, always wear a protective mask when working.
