Many car owners in the garage are dusting old tires - throwing out them either lazy, or once, or they are intentionally stored in case "suddenly will be useful." Old auto strokes are most often used to create borders, decorative flower beds, equipment of sports and yard sites, or create original ornaments for the garden and yard. One of the decor variants are swans from old car tires. Make them with your own hands will be under the power of any craftsman, only tires and some kind of tires and a couple of hours of your time will be needed from materials.
Probably does not exist on the territory of countries former USSR A town in which there would be no garden or courtyard decor in the form of automotive tires. With the skillful performance, such crafts look aesthetically, original, their creation is rapid, simple and economical with the financial and temporary side. Decorative swan, and better composition from a pair of swans will give the highlight to your site and invariably will attract the attention of guests.
Did you know? The history of the emergence of automotive tires has almost 200 years - the first such invention was patented and submitted to the public in 1846.
Create original decoration It is preferably desirable for the garden, because in the process of cutting the rubber will be heated, highlighting chemical hazardous substances, weighing that from the room will not be easy. If you work in the garage, it is advisable to wear a respirator.
Of the tools you will need such:
Important!Tires are desirable to choose "bald" and with nylon cord amplification, and not metallic - it will greatly simplify the process of working with them, and will also save on possible injury.
To begin with, consider the features of applying the markup, because without it cut the beautiful swan hardly it will turn out. First, it is necessary to draw two lines parallel to the inner tire opening, exactly half of the product - it will be wings. On the outer edges, the distance from the beginning and to the end of these lines will be equal to the length of the neck and head. The head will rest in the tail.
Main sizes of swan parts:
When all materials are prepared, you can proceed to the process of creating a garden decoration:
Important! In the process of cutting around the pattern, it is necessary to work in parallel, with small areas of 5-10 cm, immediately cutting out both sides of the swan.
In order for the decor to look more organically in the garden composition, you can additionally make a simple laying for swan from the same tires. Hats of large bolts are well suited for imitating eyes, which can then be painted in black.
Many car owners in the garage are dusting old tires - throwing out them either lazy, or once, or they are intentionally stored in case "suddenly will be useful." Old auto strokes are most often used to create borders, decorative flower beds, equipment of sports and yard sites, or create original ornaments for the garden and yard. One of the decor variants are swans from old car tires. Make them with your own hands will be under the power of any craftsman, only tires and some kind of tires and a couple of hours of your time will be needed from materials.
Probably does not exist in the territory of the countries of the former USSR town, in which there would be no garden or courtyard decor in the form of automotive tires. With the skillful performance, such crafts look aesthetically, original, their creation is rapid, simple and economical with the financial and temporary side. Decorative swan, and better composition from a pair of swans will give the highlight to your site and invariably will attract the attention of guests.
Decorate your home by crafts from lagenarium and cones. Did you know? The history of the emergence of automotive tires has almost 200 years - the first such invention was patented and submitted to the public in 1846.
Create original decoration for the garden is preferably on the street, because in the process of cutting the rubber will be heated, highlighting chemical hazardous substances, weathered which will be difficult out of the room. If you work in the garage, it is advisable to wear a respirator.
Of the tools you will need such:
Required materials include:
Important!Tires are desirable to choose "bald" and with nylon cord amplification, and not metallic - it will greatly simplify the process of working with them, and will also save on possible injury.
To begin with, consider the features of applying the markup, because without it cut the beautiful swan hardly it will turn out. First, it is necessary to draw two lines parallel to the inner tire opening, exactly half of the product - it will be wings. On the outer edges, the distance from the beginning and to the end of these lines will be equal to the length of the neck and head. The head will rest in the tail.
Main sizes of swan parts:
Garden sculptures will help to decorate the territory of the country area, interesting decision May also become decorative waterfallwhich can be done with your own hands.
When all materials are prepared, you can proceed to the process of creating a garden decoration:
Important! In the process of cutting around the pattern, it is necessary to work in parallel, with small areas of 5-10 cm, immediately cutting out both sides of the swan. In order for the decor to look more organically in the garden composition, you can additionally make a simple laying for swan from the same tires. Hats of large bolts are well suited for imitating eyes, which can then be painted in black.
When choosing a place to locate garden jewelry, it is necessary to be guided not only by its taste, but also take into account some factors, such as the illumination of the place and the falling of precipitation. Despite the paint layer, which will slightly protect the tires from the external influence, this is not enough to protect the products from deformation and cracking, which inevitably occur with rubber left in the sun. Also will negatively affect the fall in water. Therefore, it is optimally placed rubber swans In the priestly segment of the garden or under a canopy, so that they do not fall into the lunch sun and rain. Low temperatures Also negatively affect the condition of the products, because for the winter they are recommended to enter the garage.
Did you know? The largest and heavy tires are created for dump trucks (BELAZ) - the weight of the tire reaches 5 tons, and the diameter is about 4 m. The swan decor looks harmoniously near the garden pond or a waterfall, but if not, the products can be placed near the flower beds. Worn car tires can be given a second life by creating an original garden decor from them. In general, this is a great budget decision to decorate the site, creating that, you can easily spend your leisure.
D. any master class will not only breathe the second life in old tires, but also to decorate your garden plot. Today we will make kashpo from old tires with their own hands.
1. We take a large sharp knife and, constantly wasting it with water, make symmetrical cutouts on a 2/3 (240 degrees) along the side ring, as shown in the figure. The protector and side part are cut at a distance of 1/3. In the most sides, using a triangular cutout, we separate the side part.
2. We have such a cut piece of the tire.
3. Soak it.
4. Cut the beak from trimming the side part.
5. Lower tires cut along the length. The incision must be a little more than the size of the beak.
6. We insert the beak and with the help of the clamp squeeze the halves.
7. Drill drill the hole and with the help of two washers, nuts and bolts, we tighten the heads of the head.
8. To make your head already, cut off part of the tire on both sides. It should turn out like this:
9. On the main side of the tires are placed chalk and cut out the tail.
10. This species has our workpiece. It remains to paint it.
11. From the iron strips, we make a clamp, with which we are tightened by the side parts of the porridge. If there was no iron strip at hand, you can use a solid rope.
12. Now proceed to painting the parrot. Use blue, yellow, black and white paint.
13. Color the parrot inside and outside. Side rings stain with black paint. If there are no black paint, you can leave them unpainted.
14. Coloring carefully head, we try to achieve maximum similarity with the original. Black stripes and eyes make a black contour.
15. The finished porridge from the tire should be suspended with a robust rope or wire to the horizontal design. And inside can be placed a vase with a beautiful plant.
Thanks Oleg Vashchenko for the provided master class!
To do this take old tire - The older it will be, the better, since the erased protector is easier to cover with a flat layer of paint and give our handicap a more natural look.
The paint and a sharp knife will also be required, some are also used for cutting rubber Lobzik and Bulgarian - but when they are used, certain skills are needed, and it is also necessary to consider that when the tire is heated, it can start melting.
Before embarking on the cutting of the swan their tires, it is necessary to apply the contours for it, for which you will cut the items. You can think of your swan pattern, the main flew of which is the neck with your head and wings. We offer you the following scheme, which is relatively simple, but may further be supplemented with decorative details or additional cuts, slots, gear edges.
By making the necessary cuts on the bus, it is necessary to rinse well and desirable to degrease, and then proceed to painting - then it will laugh longer and will endure any weather.
After that, it is necessary to bring the wings of the swans, giving them the final form, you can also cut the gear edges of the wings and the tail so that your swan becomes very believable.
Also before painting it is necessary to fix the neck of the swan and give it the desired bending with the help of thick wire, which you disguise the paint.
And the final stage in the manufacture of a swan remains coloring his head and beak, you can also use other materials, for example, using the foam swan cut-cut in the form of a foam head, you can get a pretty cute swan, more similar to the present.
Well now your garden, the flower garden will decorate a wonderful swan. If you have a pond, then undoubtedly swan will become an excellent addition to the design and decoration of your reservoir and recreation area near him. And also, of course, the swan from the tire can become an excellent flowerumba - for this, it is enough to place kashpo with flowers in his center.
Often old tires after operation are ejected or sent to the garage, like an unnecessary trash. After all, finding them the use in everyday life is not so easy. But do not forget about the garden-park interior, more precisely about his decoration. With the help of fantasy, you can easily turn the old tires in a fence, a bench or a flower leaf on the playground. Separately, it is worth talking about creating fairy-tale characters from simple tires on the example of the swan.
Initially, the workflow is taken care of the correct selection of material. Cutting easily will be easily bald tire. Consequently, than "greasy" material, the better. Easy the whole process will help a longitudinal drawing on the product released.
Tires of a certain species have a breaker. A similar tire is bad to be separated. In addition to the whole of the region, the future figures will be sharp, hanging around the cut. What will lead to injury, both in the work and the operation of the character. Prevent the problem will help the selection of tires for working with a nylon edging.
The tire that was selected for the workflow is thoroughly cleaned from any contamination, wash and dried. Pure material is able to provide a pleasant work in all respects.
There is nothing surprising or unique in the list of needed tools.
To the number of necessary items to create a fabulous character include:
No need to forget about the grinder and the cutting disk.
As additional materials will be required:
The whole process requires patience, because it takes a significant period of time and is considered rather complicated. The whole process to create a billet for the swan is better to perform in the fresh air. And for this it is better to choose a wonderful sunny day. We swell the smell from the combustion of rubber when cutting or drilling will be difficult out of the room.
Work in a similar case will be made on a tire with a width of 16.5 cm, and the measurement of its circle is 1.8 meters. As for the classification of the tire, it is primarily as R13.
The labeling should be started with the application of several lines that help divide the working plane in half. This will be the neck of the future birds.
After that, on the protector segment, the tires are drawn with a certain sequence head, beak and the neck of the character. Better if old Material For work there will be an axial line that is well noticeable. With its absence, it is easy to fix minor defects chalk.
So, from the initial line, which is symmetric the axis, draw the beak. Its length should be 0.09 meters, while the parts width is only 0.03 meters. The beak should smoothly move into the head. Its length is 0.1 meters, and the width is 0.07 meters.
Everyone has already become clear that at the end of the head begins the neck. It expands slightly to the body. Initially, the item has a width of 0.05 m, by completion its value is already 0.1 m. Finish the markings of the bird neck is needed on the feature that divides the tire into two parts.
The last element of the melt of objects will be the tail. His outlined partially. The fork of the details is the line that came out after cutting the beak. The last step of working with the details will be the execution of two equal lines, which are located in parallel. At the same time, the distance between them should be 0.08 m, and the length of the elements themselves is 0.3 m.
This stage, as a rule, takes a lot of strength. Work on cutting material should be carried out carefully, slowly, patiently. It will not be superfluous that this item work must be produced in workers mittens from dense material. After all, the maximum protection of the hands of hands does not hurt anyone.
The means of protection in this case should not be neglected. All cutting elements produce from neck to the head directly.
You can perform this action in several different ways. It all depends on the tire density and its worn. Spoiled and very wiped material can be cut simple knife shoemaker. But the fat protector is separated by a grinder. In the latter case, the whole process will be held in smoke clubs and with an unpleasant aroma of pale rubber.
If there is an electrolovka with good power it is better to use it. Of course after doing the first holes in the material.
Previously acquired experience masters suggests that the paddle saws should have frequently located teeth. Which are directed up. So the whole process will be much easier. No need to perform work tool that is exposed to a greater speed. In this case, the speed on the contrary should be reduced twice.
To apply the jigsaw millet in the required place, make an incision with a baccoon. You can still easily drill on the end of the neck with a ten millimeter drill. The work will be more accessible if all the turning point of the markup will have the same drilled holes.
You do not need to cut at first one of the parties, and then only another. This is mistake. Since work with the jigsion will become more difficult in this case, because the strongest tool vibration will arise. Cutting all elements should be carried out in parallel. Operate need small sites at once. The length of one segment is no more than 5 cm. It will be easier to carry out the cutting, if you climb the tire itself from the inside on the cutting of the board. The segment itself can be moved if necessary.
At the end of cutting all the edges of the details that turned out, should be cut. If the protector accompanied the cord from the metal, then sharpen the wire from steel, which sticks out, Bulgarian will help. With a nylon court, the oculture is produced by an ordinary knife.
To obtain after cutting wings from the side parts of the tire, or rather the acquisition of the details of the proper scope, the cutting tire is turned on the wrong side. This process is simple - the element is turned with hands using foot support for the base of the item.
The end result: swing wing swings. But at the same time, the head and neck of the figures lie on the ground. They are still needed to bend it necessary, pre-strengthening. For this, at the very beginning of working with the character and the rod of steel was harvested.
First you need along the axis along, symmetrically to her, drill holes. They should be located pairwise. The diameter of each no more than 3 mm. They start drilling them from the central part of the head and to the point with the beginning of the poultry poultry. The distance between the recesses should be at least 0.15 m.
In the work done, the desired amount of soft wire brackets do. These brackets will become elements that will keep the rod from steel. It will give stiffness design.
Begin to lay the rod below. The protruding edges of the bracket are tightened around the main part. The characteristic bending of the neck can now be given, cutting off the extra parts. The mechanical part of all work is completed.
The finished figure at this stage looks not very attractive. Above it external species You need to still work. It will not be superfluous to double-check the presence of sharp edges on the material. This will eliminate the receipt of wounds and scratches with small researchers in the future.
You can paint the bird in white, as the swan believes. But this is not strict rules. After all, this is a fabulous character. The paint should be rack. It looks good at the beak of red, the eye of the figure can be done using round-haired bolts.
Installing the finished bird can pass on the hemp, the post or just on the surface of the earth. For the resistance of the swan, the earth is sprinkled. The ideal option It will be the creation of the base of the figure of another tire. You can paint it into a fundamentally different color.
For the first swan from the tires in the country area, you can build a girlfriend from another unnecessary material. Nobody will stand before such a decor. And the time spent on work, pay off positive emotions of friends and loved ones.
For many Russians, the country garden is not only a place where vegetables and fruits grow, but also a seating area with soul and body. Decorative ponds, garden dwarfs, flower beds with flowers, paths and other ways to decorate the garden There are a huge amount. Recently, the popularity of crafts from waste, such as plastic bottles And old car tires. In order to give the second life to serve their things, there are weights of advantages. Step-by-step instructions for learning how to cut on his own beautiful swan from the tire, will help you make such a craft!
To work, you need to choose the most old tireThe more thinned and what is called bald. The more rubber is worn, the easier it will work with it. If there is a choice, it is better to give preference to a tire with a nylon or byproke cord, and not with steel. To do this, on the tire there should be no labeling "Steel". It is difficult to cut the latter, and they are also attempting both during operation and with further use: such a bird is better not to put on the playground to avoid cuts in children.
First you need to draw on a tire "pattern" of the future swan. In the middle, celebrate the point and draw the beak from it, smoothly turning into the head and the neck of the bird. When working with a R13 tire, having a circle length of 1.8 m, the dimensions are approximately the following: the length of the beak is 8-9 cm, the head is 9-10 and a width of 7-8 cm. The neck at the beginning has a width of 4-5 cm and closer to the body It is thickened to 8-10 cm. Its length is about 75-80 centimeters.
The swan body should remain non-worn, and it is not necessary to cut it: the wings and neck with the head are connected on this part.
After the drawing of the swan from the wheel begins the cutting process. Bulgarian cut quickly, but from this rubber heats up and there is a strong smell of Gary and Sopot. Therefore, many masters prefer to do with the help of the same grinder, a drill or chisel of the label for the jigsaw blades, and continue to drink it right. It is convenient to use a reverse tooth blade at low speed. So the material will heat up less, there will be no soot, and the control over the process is better due to the low speed of work.
It will be right not to cut a completely one side, and then another, but to make small cuts from two sides one by one. So much more convenient to work, the rubber is not so strung out, besides, the probability that it will be symmetrically increases.
Next you need to turn the workpiece. It is short, but quite hard physically. To do this, it must be put the cut part to the ground, press the foot and pull up the resulting wings. As a result, it should be approximately as in the photo.
After that, the neck shape should be fixed. To do this, it is necessary to do in pairs of holes at a distance of 15 cm from each other and insert a soft wire brackets in them. With their help to attach the rod or steel plate to the neck of the bird. Next, the detail bend to it remind the neck of the swan.
After cutting and giving a swan, it will only be left to install the figure on the selected area and reapsert it. Beautiful will do not make one bird, but immediately a couple. Body paint white paint, and beak - red. Draw your eyes or form them from buttons, stones, rubber pieces.
You can also hold a stand from another tire lying on the side. Artificial reservoir or imitation, for example, from the stones will look very much by the way.
In addition to the swan, you can make other crafts with your hands from the tires. For this you need only a little imagination and time.
