Old car disk, if desired, the ability to make a small grill for the garden. And putting the grille on it, you can cook not only kebabs, but use as a grill.
Consider from different sides the idea of \u200b\u200bthe mangaal from car divisions.
Pros of such a venture:
Disadvantages:
To make a brand from car drives, you will need:
Tool:
We will look at the basic option that can be supplemented or recycled at your discretion.
Clean the drive from rust and old paint.. If you do it first, it will facilitate work.
Make a brazier from the wheels will take the day. And it turns out almost for nothing. His quality I. appearance depend on your efforts.
Very little left until the country's period, and the owners of land plots will spend a lot of time on them. Food cooked in the fresh air is much more tastier. Therefore, in this article, we will consider how you can make the design for kebabs from old car drives as you can make your own hands. Such a building has great advantages that can be operated for a long time as a mangala.
It should also be noted that such equipment will be safe and very convenient. Manufacturing should not cause complications, so every person can cope with the task. It is simply possible to cook not only kebabs, but also to establish the cauldron.
For the manufacture of metal mangala, it is recommended to use old wheels from the "Zhiguli" car. At the same time, they should be made not from an aluminum alloy, but from whole steel. If you have no disc in the garage, you can contact any tire service. If they are not given free of charge, then you need to pay a symbolic amount.
For the manufacture of the design, it is necessary to prepare the following tools and materials:
Cut partition on one of the disks. To do this, you can make notches using a grinding machine, after which itching it with a heavy hammer. If there is a gas cutter, it is more convenient to use it.
Then the discs need to be ached to the perimeter with a welding machine. Thus, the partition of the second disk will serve the bottom of the metal tank.
To use a manbon for cooking in Kazan, you need to make a small door. In this case, you do not need to remove the dish to throw the wooden fuel. This stage of manufacture is the most difficult.
To do this, it is necessary to note the rectangle, the lower part of which should be at the height of several centimeters from the bottom. In the middle of the door there will be seam left by the welding machine.
Cut the rectangle with a grinder, then treat all the edges to get rid of burrs. From the side of the bolt heads. On the cut part of the fight nuts. Thus, we made homemade loops. On the other hand, the cut fragment you need to make a hole and screw the bolt. He will act as a handle.
At the next stage, you need to brew a bottom of the future mangaal with a metal sheet so that the corners do not fall. Just need to leave not big holesTo strengthen the craving. Some experts recommend installing a grid from thick wire at the bottom.
After that prepare 3 profile pipe, up to 80 cm high. However, it's all individually, as it all depends on the growth of a person who will be cooking. Metal pipes to weld to the bottom of the design at equal distances. As a result, the brazier will be reliably standing on the surface.
For safety and comfortable use of the design, you need to make handles. To do this, you need to visually divide the disk in half, and from the opposite sides, in several centimeters from the top, you need to fight two nuts. Then to turn the coil wire in them.
To improve the appearance of the made mangala, it needs to be calcined, after which it is covered with a dark heat-resistant paint. The design is light enough and mobile, so you can take it not only on country cottage area, but also on vacation in nature.
Since old wheel drives have the same sizes, the development of a schema or drawing is not required. Everything is quite simple, as it was possible to understand from the above-described design manual instructions. It is only necessary to decide on the height of the legs to be comfortable to cook.
Below from the video, you can find out how to make a metal brand from one car disk. All work takes no more than one hour, subject to availability essential materials and welding machine.
If you show creative fantasyYou can make a beautiful and functional brand. The photo shows the results of the masters.
Choosing optimal option for independent manufacture Mangala, largely focus on the cost of materials. Old wheel drives are suitable for such considerations, since they are not only worth almost nothing, but also require space for useless storage. In addition, their form is very convenient for the placement of skewers.
With all the simplicity of the design, grinding of wheel drives from the machine are multifunctional fixtures and can replace a number of cooking devices:
In addition, the metal sheet laid over the mangala turns the device into the classic cooking surface.
Homemade brazing has the following advantages:
At the same time, there are some drawbacks:
Certain difficulties may occur during transportation of ineffective and not able to develop devices.
For self-making, those schemes where minimum disks are required are most suitable.
Before starting assembly, it is necessary to ensure the supply of materials and a set of tools for work. The following will be needed from the tools:
If options are considered how to make a brass structure, then the welding machine may also be needed.
As materials will be needed:
For the manufacture of flat hobs A metal sheet with the lengths of the parties exceeds the diameter of the disk will be required.
All work on the manufacture of mangaal is shared by their own hands on a series of stages.
IMPORTANT. In the manufacture of legs should correlate the cross section of the profile pipe and the full mass of the manga. The legs must withstand both the weight of the mangal itself and the mass of fuel, as well as the dishes along with the prepared dishes.
With the embodiments of the legs, you can familiarize yourself with the photo of already ready-made projects.
If it is planned to manufacture a mangaal of a more complex design of two or more disks, the following points should be taken into account when working:
It will be convenient if you equip the flopper door. As a door, a cut piece of the disk is optimally suited.
For loops, you can use either door loops or made by yourself. In the latter case, two nuts are welded along the side facet of the door. The door is applied in place and on the housing of the mangala are placed spaces for the welding of nuts - the response of the loops. As axes for loops, bolts of the corresponding nut diameter are used.
IMPORTANT. If you do not plan to organize stationary mangala, on the sides of the case, the handles should be accessed in advance. It is easiest to make them from segments of a large diameter wire or profile pipe.
In order for the brand from stamped discs to be used as a cooking surface, its upper part should be prepared in advance to accommodate dishes. For this weld two segments metal pipe. The distance between the pipes is selected, respectively, the diameter of the dishes.
Painting the finished barbell follows only refractory paint. Use the usual not only meaningless, but also dangerous to health. Particles of burning paintwork materials They will settle on the food prepared food.
A grill of wheeled wheels is a practical and inexpensive solution. However, it should be understood that cooking with the use of open fire is always a dangerous event. Installing a brazier and use it to take into account all fire safety measures.
Present to your attention an interesting idea For the manufacture of mangal from the car disk. The author of the idea argues that the use of the disk is justified by the fact that it is ideal because it has thick metal walls. Thanks to this, the brazier will not quickly be lit from hot coal.
So, for the manufacture of a manga from a car disk, we will need:
- car drive;
- 40 cm square mesh;
- three metal rods with threads at 8 at the end;
- metal square leaf measuring 250 per 250 mm and a thickness of 4-5 mm;
- welding machine.
Made brazed, stove, barbecue. Skolna from car disks - an example of how to re-use spent materials for useful and the desired design. These of the wheeled disks are made simply enough, they can be made with their own hands in the garage or in the domestic workshop. Although the design is simplicity, such a product can be used for many tasks.