Buy gsm thermostat zont h-1v - It means to get in the property a compact thermostat with its own SIM card of any operator, allowing you to control the climate in the room from any phone (satellite, mobile or fixed-line), tablet or PC. Most boilers have terminals closed with a jumper (corresponds to the on-board boiler) to connect a room thermostat. It is to these terminals that zont-h-1v modules are connected: this jumper is removed and the contacts of the ZONT H relay are connected to its place.
The microde company manufactures the ZONT H-1V thermostat model, almost identical to the functionality of the GSM Climate Zont H-1 thermostat, which is distinguished by different buildings and some technical features:
- The relay in H-1V holds 220V, and in H-1 it is designed for 120V;
- ZONT H-1V has a 220V-\u003e 5B adapter to convert the high-voltage signal of the boiler an alarm (in Vaillant) to a low-voltage ZONT to enter;
- the backup power battery in the H-1V module built-in, and in H-1 is missing in the basic configuration and can be purchased separately;
- The firmware in these modules is exactly the same, and the schemes are almost too.
- attached to DIN rail
ZONT H1V will provide economical fuel consumption spent by the heating boiler, allows you to remotely set the temperature in the house and control the serviceability of the heating boiler, as well as remotely manage its work!
Agree that manual control of the heating devices is quite troublesome, and almost impossible is almost impossible. With the ZONT H 1V block, the remote control of the heating system is not only possible, and is extremely simple and convenient! No matter how far from home you are not, just calling or send a team from a mobile phone or via the Internet to change the heating boiler mode and provide a comfortable temperature in the house. Convenient, isn't it?
Additional features of the device make it possible not only to save the cost of heating and monitor the operation of the heating boiler, but also follow the security of the object! The user can connect additional sensors, such as movement, opening, water leaks, gas leaks, fire and smoke sensors, etc. Information is transmitted through mobile channels and Internet.
Supports various, predefined temperature modes:
Economy - economical fixed temperature.
Comfort is a comfortable fixed temperature (usually a few degrees above economical).
Schedule - maintain a given temperature on schedule.
Disabled - Anti-Zarzania Mode
Accident - Thermostat operation mode with a faulty temperature sensor.
The module will only call the owner's phone or the trusted numbers defined by it, warning it about all changes or emergencies. Accordingly, and receive ZONT H-1V commands can only from the owner or from "their" phones. Unauthorized access is absolutely excluded - even if someone scored an error number, the device will ask for a password that only knows the owner and, for example, other family members or proxies. In addition to SMS management, the ability to control via voice menu is implemented.
In fact, the GSM Zont H-1V module performs the role of your personal assistant - called him, gave a team, for example, to heat the fire in advance, and the whole family, in the end, will arrive in warm and cozy house. Or vice versa: Forgot in the morning, leaving for work, to reduce power - no question, you can do it right from work, via the Internet.
Unlike competitors, the temperature cannot be controlled from the front panel, and all observation and management operations are performed using either a personal computer or mobile devices: smartphone or tablet. This allows the owner to control the situation where it is not, while the cost of equipment is significantly reduced.
The Zont-H1V unit works even when the cellular disappearance is disappeared by performing, for example, a predetermined weekly schedule.
It is possible to use control commands in the form of SMS text and even using the voice menu.
Used simple, functional and convenient graphical interface via a web browser or mobile application. All data is stored on the server and at any time you can see convenient and visual schedules of the system, informational messages or make the necessary settings.
Weather-dependent automation - Energy efficient heating control, taking into account changes street temperatures (The function is available for modules with a firmware version 122: 74 and above)
The thermostat measures the temperature in the room and turns on or turns off the output relay, controlling the operation of the boiler in the heating mode so that the indoor temperature corresponds to the specified value.
Controls the temperature in the house and on the street, the supply voltage, the technical condition of the boiler and signals when an accident or shutdown of the supply voltage. With the deviation of the values \u200b\u200bfrom the specified, it informs the owner by any predetermined method: call, SMS message or alert via the Internet.
To use the Internet service, you do not need to install additional software, the work is carried out using any modern web browser. Internet access is accessed through a personal page on the zont-online.ru server.
From the personal account on the Internet service zont-online.ru, you must specify the values \u200b\u200bof the desired temperature inside the room, as well as threshold levels to generate alarm messages when the temperature is deviated to the critical (emergency) value.
The unit analyzes the temperature indoor temperature using its own remote temperature sensor. Depending on the measurements made, it turns on or off the output relay that controls the operation of the boiler in the heating mode so that the temperature inside the room corresponds to the value of the specified operation mode.
If the boiler malfunction occurs, the system will immediately notify the owner about this event, which will avoid trouble.
Thermal sensors (wired)
Connects to 4 and 6 thermostat contacts in accordance with the proposed scheme. At the same time, up to 10 pcs can be connected. The remoteness of the latter in the plume is not more than 100 m. Long branches from the main loop can lead to the inoperability of all sensors.
Cote control output
Contacts 1, 2 and 3 thermostat are designed to connect to a heating boiler. Contact №1 - General (O), Contact number 2 Normally closed (NZ) and contact number 3 (HP) - normally open. The device connects to the boiler contacts intended for connecting a room thermostat.
GSM antenna
Connects to a separate input and is located in the room in such a way as to ensure the maximum sustainable reception of the GSM signal.
Main Food + 12V
From the 220V network via the power supply (220 / 12B network adapter) from the delivery kit.
Backup power + 3.7V
From the built-in Li-Ion battery.
Login 1. Analog entrance - contact number 5.
Designed for connecting: or security sensors; or signal "Crack accident"; or room thermostat
Login 2. Digital input - contact number 8.
Designed for connecting: or security sensors; or signal "Crack accident"; or room thermostat; Or the OpenmentHerm interface and a radio module ML-489.
Important!
You can not simultaneously connect signals from an external room thermostat or signals "Accident Cup"
You can simultaneously connect 2 OpenTherm interface and Radiomodul ML-489
Remote control of the work of the boiler can be carried out:
- SMS commands;
- when dialing to the SIM card number using the voice menu;
- via the Internet (web-interface and mobile applications for Android and for iOS database devices).
Convenient and simple web-interface with features:
- display of the current state of the boiler and temperature indoors;
- boiler management;
- temperature monitoring (inside, outside the room, coolant) for any selected period of time;
- programming work boiler on schedule;
- Alerts about the triggering of additional sensors.
Different events alerts:
- with the deviation of the measured temperature from the specified threshold values;
- about the cape of the boiler (subject to the connection of the thermostat for the emergency outlet of the boiler);
- about the malfunction of the thermal sensor and the transition of the thermostat in the emergency mode of operation;
- about the disappearance or restoration of power supply, while it is necessary to have a backup battery;
The event log
- diary measured temperatures for any period without limitation period;
- Date and time of detection of the boiler crash;
- date and time of changing the mode of operation of the boiler and thermostat;
- a list of executed control commands via voice menu transmitted by SMS, software updates;
- Date and time of disappearing or restoring power supply.
Signaling on the state of additional sensors connected to the "alarm" input of the thermostat;
Memory of events:
- indications of the temperature sensor;
- dates and time of the cauldron of the boiler;
- changes in operating modes;
- voice menu commands
- SMS commands;
- Updates software (BY);
- Turns / power off.
Update The current version of the block firmware without shutdown and dismantle from the user's personal account.
Zont H-1V Supplies Set
Basic block: 1 pc.
External GSM antenna: 1 pc.
Temperature sensor (digital, wired): 1 pc.
Power supply (network adapter) 220V / 12V: 1 pc.
Converter Signal Alarm Boiler 220 / 5V: 1 pc.
Operating Instructions: 1 pc.
Thermostat packaging 
Article: ML13213.
Manufacturer: MICROLINE (by request Evan)
Power supply: 10-28V
Maximum current consumed: 150 mA
Number of inputs: 2
Number of outputs (type - Dry contact, closure / opening): 1
Type of connected wired thermal sensors: DS 18S20
Type of connected radio drivers: ML-703
The total number of simultaneously connected thermal sensors (wired and radio): 10
The maximum allowable loop length with thermal sensors: 100 m
Maximum current through relays: 1000 mA
Maximum voltage of switched contacts relay: ~ 220 V, \u003d 24 V
Voice interface: yes
Web interface: yes
Interface 1-Wire: yes
Temperature range of work: from -30 to +55 ° C
GSM-modem frequency ranges: 800, 900, 1800, 1900 mhz
Data Transmission Channel: GPRS
GSM Antenna: External
Internal non-volatile memory: yes
Backup Food: Built-in Li-Ion Battery 103450-RSV-LD 2000 MH
Output time: no more than 50 seconds
Medium service life: 7 years
Overall dimensions, mm: 90 x 50 x 55
Mass, no more: 0,200 kg
Case: Plastic on Din Rake
Additional compatible equipment ZONT: ML-489, ML-703, ZONT HOME, OpenTherm interface, Astra-9, Astra 512, Astra C, Io 102-16 / 2, Astra 361, ML-711, ML-712
The function of diagnostics of heating installations in automatic mode allows the user to solve almost all problems without contacting the service. For Gas boilers Vaillant Error F20 - a rare phenomenon. Understanding what reasons she is called, it is easy to identify a problem and eliminate on their own.
Recommendations for eliminating F20 Vaillant error, found on forums, thematic sites, different. It appears when the boiler overheating, and the reasons for this several. The nuance is that other codes are indicated in the instructions: F0 ( heat At the feed), F22 (sharp drop in the pressure of the coolant) and a number of others.
Not everyone understands the difference between the Vaillant boiler sensors. The devices installed on a straight line and returns track the current temperature. The thermostat of overheating is triggered by the value of T˃ 95 0 s at the output of the heat exchanger and turns off heating installation By alarm signal with an F20 error. Therefore, with him and you need to understand.
Reset pressing a button on the Vaillant control panel. Imported boilers are sensitive to the supply voltage, and when network is instability, there are failures with an indication of any error. If it is false, easily reset.
Button 8
"Elimination of failures" to reset certain failures
Bring the thermostat to the working position. In the boilers Vaillant "shall" manually, pressing the rod (painted in red). If the F20 error is caused by a failure in the pump or a different reason, it will disappear. To access the overheating thermostat, you need to learn the front panel - in most VAILLANT models, the protective device (fuse) is set at the output of the heat exchanger, under the NTC sensor.
Location Sensor NTC Copper Wilant
Step 3. - diagnostics of signal chains. Defects are determined visually: the lines of the line, the insulation melting, the closure - the causes of the F20 error and the emergency stop of the Vaillant boiler. The reliability of contacts is checked, the absence of oxides.
Step 4. - Testing the overheating sensor. Determine the health is easy to multimeter, measuring resistance. In the initial state, the operating device contacts are closed, R \u003d 0. The protective thermostat is not repairable - changes.
The last reason causing the F20 error is the Vaillant boiler electronic board. It forms a malfunction code over a signal from the overheating sensor. Independently to identify a defect without schemes, experience, the corresponding devices will not work. If the measures taken to eliminate the F20 error failure, you need to contact service center. After replacing the board, the boiler work will be restored.
Many buyers of boilers Evan Warmos QX have decided to use the remote control and GSM control device and control the EVAN module. In passport GSM module It is indicated that the GSM modem has a special entry of the "Cable Accident", which must be connected to the output of the boiler accident.
However, as it turned out as a result of a request to the manufacturer, Warmos boilers do not have the output of the "Crack". This is explained by the fact that the electronics of the boiler was developed earlier than the GSM modem Evan.
According to the numerous requests of the Customer Factory, the technical specialists of the company have developed a Warmos QX and GSM Module Evan Module Coupling Unit. The compact device is made in an inapproprous embodiment and is a digital pulse signal converter of the EUVAN boiler indication board.
The output stage of the device controls the relay module contact group. A pair of normally open contacts is connected to the input of the GSM module and "minus" power supply. When blocking the boiler, the relays are closed and low potential will arrive at the accident.
The mounting of the pairing unit is made using the mounting glue, the location is next to the Warmos QX boiler indication board. The protection of the block from the possible effects of the coolant is not fulfilled - we recommend performing yourself.
The main complexity for the installer represents the connection of the input of the pairing unit to 11 output of the indication board processor. The density of the circuit board on this site is high enough, so we recommend using a miniature soldering iron. The three remaining connections perform quite simple - the places of the bundles are shown in the figure.
Warmos QX and GSM Module Evan Module Coupling Blocks are at the stage of experienced production by limited series. In the first half of 2015, the pairing blocks in the case variant will be available. Pre-orders for the pairing unit are accepted by email. [Email Protected] or through.
2017-03-22 Evgeny Fomenko
During the connection, operation and maintenance of heating gas boiler Vaillant may arise some faults. Models in which installed electrical system Controls with the screen, make it possible to understand what specifically does not work in this situation.
To understand what to do in various cases, consider the widespread codes of errors of the Gas boiler Vailant, and what needs to be taken with their occurrence. If several errors occurred at once, then they are displayed alternately approximately 2 seconds.
The designation of icons can begin with the letter F (error) or S (state). Specifications and codes that are inherent in each specific model are spelled out in the instruction manual.
Error F5 means the rupture of the external sensor of the exhaust gases. Possible reasons There may be incorrect operation of the exhaust gases sensor, the plug is taken out or damaged cable, the spare resistor is incorrectly installed. The code is relevant only for the hinged model of Vailant Atmo.
If the display shows alternately, the water temperature and the error 5er (or ser) is reminder - it is a reminder that it's time to spend time maintenance Devices.
The user himself can set the frequency of how often this reminder pops up. The value is set at the D.0 paragraph D.084 within 0 to 3000 hours at a 10-hour interval (the number 300 corresponds to 3000 hours). To completely disable this feature, enter the "----" symbol instead of the numeric value.
F15 error shows a short circuit of the external sensor for exhaust gases. Provisitively arisen with a sensor fork housing, a short circuit inside the harness with wires or the sensor itself is faulty. It is shown only in wall-mounted boilers Vaillant ATMO.
The error F20 (F20) reveals that a protective disabling of the device occurred due to the fact that the safety limiter was triggered by the STB temperature limiter. It works when the maximum temperature is exceeded.
This may occur due to the fact that the contacts of the "masses" of the wiring harness with the case is incorrect, the NTC breakdown of the reverse or feed line (weak contact). Possible breaks through the ignition wire, electrode or ignition plug.
F21 error means emergency shutdown of the GFA flame control automaton.
Error F22 (F22) shows the triggering of the protective disconnection due to insufficient amount of water. The reasons for this malfunction of the pump cable or toggle with an insufficient amount of water, the pump does not work or blocked, or it has too small power.
F23 error reveals emergency shutdown due to too much temperature level drops from sensors located on the feed and discharge lines.
Error F24 signals an emergency shutdown when the temperature is too sharp. This means the availability of air in the device, reduced pump performance, its locking or very low pressure in heating system. A gravitational type valve can be connected or blocked.
The error F26 means that the flow of the gas valve of the stepper motor is not determined due to the breakage of the gas reinforcement. It is possible that the gas reinforcement servomotor is not connected or polnean, the connector is incorrectly delivered in a fee or bursting in the wiring harness.
The error F28 (F28) shows that the equipment did not turn on, a malfunction was revealed when the device starts, the ignition attempts are unsuccessful.
There are a number of options:
Electrode ignition Kotlp Error F 29 (F29) expresses that the flame burner sweeps during operation and further attempts to ignite unsuccessful. It may be temporarily stopped supplying fuel, the ignition of the ignition of the ignition transformer or the incorrect grounding of the equipment.
The F33 error (F33) reflects that the instrument for measuring pressure force is not included. After turning off the fan, the pressure relay does not disconnect the contact. Relevant for the Wilant TURBO TURKE TURKE PRO.
The S33 error indicates that the device is blocked and translated into a state of 20-minute waiting, the mode of protection of the heat exchanger from freezing was activated. The reason is that the contacts of the relay of the air-gas tract are not connected. This state may appear in two-circuit boiler Wilant 242 turbo.
Gas boiler Vaillant Turbotec Pro 242
Error F36 (F36) - Tipping sensor traction recognized the output of combustion products. Shows that too weak thrust. Most likely, the chimney or closed ventilation is closed. The elimination of this problem is to clean the chimney, turn off the active exhaust over the stove and opening the window.
Error F 37 (F37) means the deviation of the fan rotation speed (too fast or slow). Perhaps Paul Pressure Sensor.
The F38 error indicates that the fan has failed and requires replacement.
F53 error shows incorrect combustion settings.
Possible reasons:
F61 error indicates an error in managing gas valves. It may be damaged by the supply of a cable harness and a closure occurred, a malfunction of gas fittings or an electronic board.
Error F62 - delaying gas reinforcement time. It can work if there is an extraneous light in there (the control electrode does not show the flame attenuation).
The F71 error shows the temperature sensor failure in the feed line. It is probably faulty or is at a large distance from the feed line.
Error F72 appears when the reverse or feed line temperature sensor fails. It can be faulty or highly large temperature difference in direct or reverse NTC sensors.
The F75 error (F75) means that there is no pressure hopping during the power on. There may be oxygen in the heating system or the pump or the water sensor incorrectly works. In order to correct the situation as quickly as possible, the adjustable bypass is checked, the expansion capacity to the reverse line is connected.
Gas boiler pump
The server error is the same as the code 5er (the letter "S" and digit "5") is equally displayed on the electronic display. After the problem is eliminated, errors are reset after pressing the "Reset" button or turning on and off the boiler from the network.
If the diode is blinking a diode, then or it is faulty, or combustion products are not completely outlined, but enter the room. Instructions for repair in this case are as follows: First, you should clean the chimney, then check the quality of the ventilation.
After that, you can replace the reverse thrust sensor. Initially, when installing, it is important to comply with all safety requirements. Quite often clogs gas-burnerThe soot is postponed on it. It should be cleaned regularly to fully control the flame level.
