Vacuum valves
Vacuum valve or aerator sewer applied in internal sewage systems to obstacle to the room unpleasant odors, harmful gases and vapors from the system, as well as for discharge of pressure in the system. The vacuum valve 110 (aerator 110) is installed on top of the vertical risers in the sewage system in attic rooms, toilets, bathrooms, etc., where the uninterrupted flow of fresh air will be provided to the valve.
Also, the vacuum valve is used for the local aeration of the shell, bidet, toilet bowls, where the high flow rate of the waste fluid can lead to the creation of air defrustion (sucking water from the siphon hydraulic assembly), in this case, as a rule, a vacuum valve 50 is used.
Plug
Designed to close the unreleased flaring compounds of the sewer pipeline.
Umbrellas
The umbrella sewage ventilated is designed to protect the sewer rims derived on the roof of the building.
Cross
Single-bed crosspiece is designed to connect to the pipeline of additional branches in the same plane. Two-plane crosses are designed to connect to the pipeline of additional branches in two planes.
Two-tempeablum couplings
Double-standing coupling is used for installation of non-pressure sewer pipemaintenance internal systems Sewage of buildings and structures various destination. The coupling has a two-stroke design and is designed to perform pipe connections on both sides, thanks to the jumper on the inner surface of the coupling.
Check valve
The inverse sewer valve is installed in the input places into the common sewer system to prevent reverse stream. wastewater With the possibility of using forced lock.
Taps
Used to change the direction of pipe gasket during the installation. Thanks to the sewer removal, you can turn the pipe to any side. This is especially in demand when complex pipeline systems are mounted and it is necessary to hit an angle or an architectural protrusion.
Taps 110 with 50 exit
Used to create taps and bends, as well as connecting additional elements and plumbing devices of sewage communications.
Compensation nozzles
Used to compensate for building tolerances.
Transitions to cast iron
Applied to transition from the termination polypropylene pipe On a smooth end cast-iron pipe. For hermetic compound, a special rubber cuff is necessary.
Eccentric transitions
Designed for the reduction of the flow and compound of the sewer tube / larger diameter fitting with a smooth end of a pipe / fitting of a smaller diameter.
Attaching to the toilet
Attaching to the toilet is designed to connect the toilet to the sewage system. Basically applied with a horizontal attachment method.
Revision
Designed to clean the sewer riser.
Tryes
Designed to connect to pipeline D110, D50, D40 and D32 additional branch at various angles
Khomuta
Used to fix the elements of the system, the distance between the clamps should be: for horizontal lines - 10 diameters of the pipe paved, for vertical lines (for risers) - 1000-2000 mm
PP PP compensatory Du 110 mm sewer PVC internal one-toastrous groove PP D 110 mm for internal sewage
F.asconia for connecting sewage PVC. pipe and shaped parts of non-bodied connections. Thrust board in the coupling design provides proper installation Pipes and fittings. The shaped parts of PVC provide a dense hermetic connection of sewer pipes. Curses have a high-quality rubber seal, resistant to aggressive media.
Nozzle compensation for internal sewage - Gray polypropylene sewer fitting. It is designed to repair the main sewage network in both residential and non-residential buildings and premises.
Sleeping nozzle compensation It has a long service life (at least fifty years). Standard diameters of this fitting coincide with standard diameters of gray sewer pipes and make up 5 and 11 centimeters.
Company " Pipe Plast"Offers compensatory PP nozzles at competitive prices in Moscow. They are used in the original pipelines of internal networks of the sewers of administrative, industrial and residential buildings and structures.
The main characteristics of the pipes:
Products correspond to domestic GOST and international technical standards. Delivery of products can be carried out in any region of Russia.
Compensatory pipes From polypropylene PP is necessary to compensate for building tolerances, simplifying assembly and assembly work. It is recommended to use at the bottom of the risers in the technical premises. The presence of a nozzle makes it possible to avoid the deformation and destruction of pipelines, makes it possible to remove damaged network elements without its parsing.
Thanks to the fusey design, the nozzles are simply installed. They are equipped with a sealing rubber ring, which provides high tightness and reliability of the connection. Additional qualities: corrosion resistance, aggressive environments. It may function normally, both at high and at low temperatures.
Often, in the process of replacement of the pipeline, it is necessary to face the diameter of one end of the highway is 110 mm, and the cross-section of another is greater or less. And how to replace the sewer riser? A compensator is useful - an excellent transition device, just intended for connecting elements with a difference in cross section.
By definition, the compensator is a device for compensating for linear lengthening of the pipe system. Each material has individual indicators of linear extensions, so the compensator is not needed for each pipe line. The relevance of the element increases in the case of the presence of a sewer system, pumped into a screed, wall. By appearance The element is a corrugated nozzle, equipped with both sides by flanges connected.
Important! The use of flanges is shown for pipes with a cross section of 63-110 mm, a thread compensator is available for pipes to 63 mm, as well as an element equipped with a rubber corrugated seal and a precipitant nut.
Sewage compensator plastic shown for repair / replacement PVC pipe Without dismantling the whole system. Introducing a piece of curved shape, the compensator has a cross section the same with the elements of the highway and is inserted by cutting out a piece and sealing the compensator of the solder lamp.
Tip! Compensators are mounted only on sewage designs or hot water taps.
Often the installation of an item is required to repair a bath or toilet room, when the flooring drops require lifting or lowering the crossbar onto the setting of the wastewater angle into the sewer.
Polypropylene elements have almost universally replaced old metal sewer risers. Due to the unconditional advantages, plastic is becoming increasingly popular. However, in order to get a really high-quality result of the insertion and install the compensator correctly, some simple factors must be taken into account:
Important! It is very reasonable to provide increased strength to the thick walls of pipes, for which the weld method of the installation is applied. Welding is also indispensable if the sewage pipeline is intended to be used in the conditions of increased temperature effects.
Scheme of working in a plastic riser:
And advice: to connect the pipeline whose items are made different materials A system of fittings equipped with a polymer coupling and tubular carvings is used. Now you do not have to guess why you need a nozzle and what to do with PVC pipeline, if it has been completed, the compensator will allow you to quickly and without any special work and time costs to fix the breakdown without disassembled the entire system.
