Swans for the garden with their own hands from plastic bottles will add grace and beauty to any palisade. Today there are many ways to decorate a garden, but the most unusual decorations can be made at home. Such decoration does not require large expenses, but you can use your imagination to revive the exterior. And rarely, who will refuse a small flock of beautiful swans in their own garden.
There are several ways to make such swans, they differ only appearance and the time used to create such masterpieces.
The first method just does not take much time, but the result will certainly delight the eye.
To make a swan for a garden, you will need the following materials and tools:
A 5 liter bottle is taken. It is necessary to mark the lines with a marker, along which it will need to be cut in two, the upper part is removed. Only the neck remains, which is necessary to fix the neck. The hose, which plays the role of the neck, must be threaded through the neck and secured with wire to the base. Next, you need to tackle the "feathers". Blanks are cut out of white bottles (more often they come from under milk), get rid of the neck and bottom. The cut blanks need to be held over the candle from the outside, it is advisable to cut a small fringe on the sides of the blanks for a more realistic look. Then you need to collect 2 feathers and wire them together.
In the design of the neck, bottles with a cut-off bottom are also used, according to the number of bottles used, you can choose the length of the neck. Now it's time to start creating the beak.
In the place where the hose and the last bottle end, you need to make holes and connect everything with a wire. Close the base of the beak with a lid. The beak itself will be made from the cap most commonly used for chemical bottles. It is necessary to cut the cover in the shape of "M", then paint and install the beak. If desired, you can plant flowers for the garden in a flowerpot, and then an ordinary flower bed will become a work of art.
There is 1 more way to create a swan for the garden. In this case, we use unusual solutions... So, you will need the following materials:
At the beginning of work, it is necessary to cut off the inner rings from the tire, and to indicate the tail, one side is cut out triangular special tools. We cut the tire in front for convenience, the edges are bolted together. To create a neck, you need to screw the wire to the tire, and leave quite a bit of material below in order to fix the swan in the ground in consequence.
The wing is assembled from feathers, made in the same way as in the first version, but this time the "fringe" is optional. All prepared feathers are screwed into 2 mesh sections, which will be the "skeleton" of the wings.
It is necessary to fill in several rows with feathers and on the inside of the net, so that in finished version no frame was visible.
It is advisable to take a larger mesh to make the wings look more spectacular. But the head is cut out of polystyrene, the beak and eyes are painted. The head is placed on the wire base after the self-tapping hose has been used to create volume in the neck.
The body, like the head, is painted, and the wings are installed with self-tapping screws or wire as soon as the workpiece is dry. The swan is ready to decorate the landscape.
The latter option for garden decoration is more time consuming, but the result is worth the time. For a swan planter, you will need the following:
First you need to repeat the already familiar steps with a 5 liter bottle - cut off the top, but leave a neck for the neck. Pour wet sand into the bottle, round the sides. Insert a rod in the shape of a “two” into the lid.
Put 5 cm of putty on the polyethylene, place a bottle on this layer, smooth the excess putty up the base with a spatula soaked in water. Next is the neck. Form a roller of putty and apply to the base of the rod and the lid. Smear the irregularities with a damp brush. Next, treat the entire surface of the bottle in the same way.
Until the putty has grabbed, you need to tackle the wings.
Press the mesh on both sides of the body at a slight angle. Supporting it from the inside, it is worth starting to apply putty, imitating the wings. Next, it is worth sticking around the neck in the same way and forming the head. At the end, wrap it with wet bandages. In this case, you need to fix the neck so that it does not fall under the weight.
Leave for a while and take care of the tail. A small piece of mesh is placed between the wings, pressing into the filler layer. Next, the tail is formed in the same way as the wings - a roller of putty is applied to the mesh, and layers are added, then errors are removed with a damp brush.
The next step is to apply 1 more layer of putty on the neck and head. When everything is over, you need to walk with a damp brush and finally remove the irregularities. It is required to leave the swan in the sun for 2 days for final drying. And as soon as the workpiece is ready, it is necessary to sand, paint, shape the beak, eyes and paint with varnish. And flowers should be planted in the container in the center of the figure, and the swan is ready for the garden.
There are several ways to create the most beautiful figures of swans for the garden from available tools. And which of the options to choose depends on your own imagination and desire, since there is nothing difficult in this. And let each garden find its own "swan".
The swan has always been a symbol of beauty, grace and grace. Making a swan from plastic bottles with your own hands is not difficult. Although you need to show perseverance, patience and spend a little time, then a beautiful swan made from simple used plastic bottles will be a great decoration for a garden or summer cottage.
This article will present a master class on crafts, two techniques for making a swan with detailed instructions, which are supported by photos and videos.
Here are some photos of how the swan should look like:
First, it is important to choose a place in the garden or in the country in which the swan will stand. This original bird is used as a tub for flowers or other plants. The name of this craft is the swan flowerpot. A stunningly effective and functional thing.
For crafts, you will need materials such as:
It is necessary to cut the bottle in half, bend the wire and make it look like a number two, make a hole in the bottle cork and insert the wire. Strengthen the structure with a special glue for ceramics, and to make the product stronger inside, cover it with stones or broken bricks. Fill the hole with wet sand.
How it works? Under the pressure of the sand, the bottle should become more rounded and take the shape of the bird's body.
The workplace for working on the craft should be covered with cellophane. At the next stage of work, it is necessary to make a putty solution. To make the swan easier to sculpt, you need to make the solution thicker. In order to make the bottom of the product, the first layer of putty must be spread directly onto the cellophane.
Place the bottle on top of the solution and gently smooth out the layers with a spatula.
The next step is to blind the bird's neck. To do this, you need to start coating the wire with putty. Start from the bottom and do it with wet hands.
In a similar way, coat the entire bottle with a spatula, with a thick layer of two centimeters.
To make the wings of a bird, you need to bend the mesh into the shape of a wing, attach the bottle to the side and press down, fix it with putty. Wait for the solution to set.
When the putty has grabbed, coat the bird's wing with the solution with your hands.
While the wings are drying, you need to smear the bird's neck.
During the working process, wrap with a wet white bandage.
It is required to form the tail of the bird. To do this, bend a part of the mesh at an angle of 40 degrees and hold it with a solution. Then hold your head and leave the product to dry for 30 minutes.
From the bottom of the tail, make a roundness at the bottom of the tail.
Make the top of the tail in several steps.
Top view of the tail.
Side view of the ponytail.
When the swan blank is ready to dry, you need to plaster it, paint it with white paint and varnish it.
The beautiful swan is ready!
For crafts, you will need the following materials:
First you need to prepare the bottles. Remove the neck, plugs, rings, peel off the labels. Next, you need to cut the bottles, but before cutting, draw clear lines along which to cut.
Cut a half-liter bottle, remove the neck and cork. Make cuts to the cone of the bottle. Make the first cut along the molded seam. Next, make a beak, melt the ends of the clothespin and pin two holes with an awl. Tape together two halves of the clothespin. Make the body of a swan with a 5 liter bottle.
Next, you need to assemble the product. Bend the thick wire in two and pass it through the wire in the bird's head. Put a synthetic winterizer in the head and string the plugs on the wire alternately with 6-petal parts.
This is how the neck should be:
To strengthen the body, you need to pass the neck part of the wire through the bottom of a five-liter bottle and bring it out through the hole in the lid. To stabilize the product, fill the bottle with stones. Make a tail from the ends of the line. Cut and reinforce the feathers with synthetic thread.
The craft of the majestic swan is ready!
Easy videos on how to make a beautiful swan from bottles.
Before making a swan from plastic bottles, you should prepare all the material necessary for manufacturing:
We prepare the necessary materials
In addition, a set of the following tools will be involved in the manufacturing process:
Despite the fact that a do-it-yourself swan from plastic bottles is easy enough, nevertheless, you must carefully follow the entire sequence of actions. The process of manufacturing a plastic structure takes place in several stages.
All elements that are required for manufacturing must be prepared very carefully and carefully.
The step is to carefully remove the caps and rings from the bottle necks and remove all stickers and labels.
We cut the bottle along the outlined lines
To make a straight cut, it is necessary to apply a preliminary marking.
The bottom line of the marking should be one centimeter away from the uppermost corrugated part and run parallel to it around the circumference of the entire bottle. The top line should extend two centimeters down from the bottleneck and run parallel to the circumference of the entire bottle.
Both parallel marks are connected by a third straight line. Then the most accurate cut of the plastic is made in accordance with the markings made. The result should be three details.
To make the neck, it is necessary to cut the neck part of the blanks to the thread into six identical fragments. The taper is cut into eight pieces.
All the corners formed as a result of the cut must be rounded off, and three paired holes must be made at the base of the resulting "petals".
A neck with a cork should be cut off from a half-liter bottle. Further, parallel cuts are made in the cylindrical part of the bottle until the transition to the tapered part. The reference for the first cut is the casting seam, and all subsequent cuts are in increments of five millimeters.
Straighten the ends of the swan beak clothespin
In order for the clothespin-beak to lie as tightly and evenly as possible, it is necessary to slightly melt its ends and pierce it with an awl through a pair of holes.
Through the holes of the clothespin attached to the bottle neck, it is required to make similar holes in the plastic. In addition, it is necessary to make holes for the buttons-eyes, choosing the most optimal place.
For making the body of a swan, a five-liter bottle is ideal, in the bottom and lid of which you should make a pair of holes to secure the wire neck frame. A small "window" is cut out in the sidewall of the bottle, which will allow the hand to pass freely inside the bottle.
Finished items must be assembled in a specific sequence.
We fix the eyes and insert the beak. Fill the resulting voids with foam
For attaching the eyes, buttons and a piece of thin wire are used, which is twisted inside the bottle with pliers. Using synthetic threads, a beak-pin is sewn, from which a metal ring has been removed.
To fasten the two halves of the clothespin, you need to use tape. The free space in the beak is filled with a piece of foam and isolon, on top of which double-sided tape and a piece of red cloth are glued.
We string the prepared six-petal parts around the neck
A strong and thick wire bent in half must be passed through the wire attachment in the swan's head. A synthetic winterizer is laid inside the head, and plugs are strung on the wire, which alternate with six petal parts.
The fringe made on the head should be tightened with fishing line on the neck.
Initially, the neck wire is passed through the bottom of a five liter bottle and then exits from the holes in the cap. The wire is guided by hand through the cut "window".
To stabilize the position of the finished swan, fill the bottle with small stones that will give the body weight. The ends of the wire are fixed at the exit from the cover in the form of a tail. Over the frame of the entire body, elastic tights are pulled in a double layer.
Sew on feathers
The cut out "petals" of feathers must be fixed on the body, starting from the tail section. Each subsequent row of feathers should slightly overlap the previous one, which allows you to hide the attachment points.
Strong synthetic threads are used for fastening. The plumage of the ends is carried out by attaching single plastic "petals".
About making a swan from plastic bottles with your own hands, see the video:
Want to decorate your country cottage area? Why not use the simplest and most affordable material - plastic bottles? Today, with the help of this raw material, various figurines of animals and plants are created. Distinguished by durability and wear resistance, such crafts do not need care, they perfectly tolerate any weather and will delight your eyes at any time of the year. The topic of this article is - swans from plastic bottles for the garden with your own hands. In it we will discuss how to make such a decor as quickly as possible and what is needed for this.
Swans from plastic bottles for the garden Swans are always very beautiful and romantic. But we offer you not only to enjoy plastic swans but also think about how to make them functional. For example, some people use a ready-made swan figurine as a flowerpot. This design fits perfectly into landscape design your site. The best part is that you don't have to be a master and own a special tool to build it. Such a product will be within the power of even beginners.
You will need the simplest materials: large plastic bottles of 5 liters - 2 pcs., Wire, metal mesh for the wings and putty. Usually, all of these materials remain after renovation or construction work.
The main stages of work to create swans from plastic bottles:
Stage 1. First you need to cut a hole in the bottle to create a flower bed.
Stage 2. To give the bottle a rounded shape, it is recommended to cover it with sand so as to form a circle. This flower bed will also be the body of the swan, so it should be slightly oval.
Stage 3.
Stage 4. Preparation of the base. To do this, you need to displace a certain amount of putty, lay it out on a plastic wrap with a layer of 5 cm and put a bottle with a hole made on top. Leave to dry for a while. As soon as the putty dries, it will turn into an original swan stand. To make it easier to work with the putty, it is necessary to periodically moisten the spatula with a small amount of water.
Stage 5. Creation of a graceful swan neck. To make the neck look attractive and preserve for a long time, you need to roll up small rollers of putty and press it into a metal rod. A large piece will fall off immediately, so the most The best decision- create a neck from small pieces. After the next piece, the neck is wrapped with a bandage. It is also important not to forget about naturalness, because in a real swan, closer to the body, the neck begins to thicken. You will have to do the same.
Stage 6.
Stage 7.
The swan figurine is ready. Now you need to give it time to dry completely, taking it to a place protected from rain and sunlight. Once the product is dry, it can be cleaned with a fine mesh to create a beautiful, flat surface... The putty is primed before painting. What paint is better to paint a swan? Any base can be suitable for this, but it is more practical to use enamel paint. It is convenient for her to draw eyes, beak and feathers. After that, the entire structure is opened with varnish to fix the result.
Swans from plastic bottles DIY garden- original, beautiful decor that will delight your eye and decorate landscape plot... We hope our tips will help transform yours by adding your own creation.
